Data Sheet

IT Networks
TEST FOR HIGHEST NETWORK SPEEDS
WITH YOUR QUALIFIER
The new NetXpert XG verifies, if cabling channels support
maximum transmission rates of up to 10Gbit/s, irrespective of
cable categories, patch panels, or outlets installed. NetXpert XG
provides a precise statement by automatically performing three
individual tests which are combined into an overall test result.
By performing a sequence of various tests the NetXpert XG verifies
error-free data transmission up to 10Gbit/s. Determination of
Signal-to-noise ratio (SNR) followed by a Bit Error Rate Test (BERT)
and delay skew test qualify Gigabit transmission. Delay skew
indicates the signal time delay between the wire pairs used.
Excessive delay can result in a serious degradation of transmission
performance, making it impossible for the receiver to interpret the
data stream correctly. Delay skew, just as the signal-to-noise ratio, are
considered to be crucial parameters for a reliable data transmission.
New standards defining data rates up to 10Gbit/s are big
challenge for latest generation qualifiers. Particularly cabling
for wireless access points has to support ever increasing
data rates. In order to verify if the cabling installed is able to
support the increased data rates, operators need to perform
adequate testing before commissioning the network, to avoid
any unpleasant surprises.
NetXpert XG enables you to meet the new challenges now!
The generation of “Ethernet Speed Certification”
ACTIVE NETWORK MANAGEMENT
• All network tests via copper, fiber optics and WLAN possible
• Supports IPv4 and IPv6
• Detection of duplicate IP addresses in the network
• Discover your network and see the connected network devices
• Identifies defective PoE switches with a PoE load test
• DHCP test
• Ping lists can be defined and saved for later use
• LLDP/CDP detection and analysis
• Identifies VLANs present in your network
• Data transfer from the tester to the PC using USB stick
TROUBLESHOOTING OF ACTIVE PoE/ PoE+/++
NETWORKS
For active PoE network troubleshooting, NetXpert XG additionally
offers a comprehensive tool set. This includes load tests for voltage
drop to verify stability of PoE supplies, identification of the devices
connected to the network, and detection of availability of priority
devices.
NetXpert XG offers sufficient internal storage even for large
projects and, if required, generates complete standards-based test
reports containing all the necessary information.
PERFORM CABLE TESTS
• Tests data cabling for IEEE 802.3 compliance at data rates
of up to 10Gbit/s
• Bit Error Rate Test (BERT)
• Signal-to-noise ratio (SNR)
• Measures delay skew
• Combined length measurement performing TDR and
capacitance measurements for highly accurate test results and
easier troubleshooting even of shorts
• Full-color wire map shows opens, shorts, miswires, and split
pairs in a clear and easy to understand way
• Saves test results and generates standards-based measurement
reports providing “Pass/Fail”
INCLUDING PORTS FOR FIBER OPTIC MEASUREMENTS
The NetXpert offers full flexibility regardless of whether you are
measuring fiber or copper cabling. Using its available SFP/SFP+
ports, various active fiber tests such as protocol detection (CDP/
LLDP), network ping test and network discovery can be performed.
In the area of passive tests, qualification of fiber optic cabling will
be possible by connecting one main unit at each end.
Extensive accessories turn NetXpert XG into the ultimate multi -
tool – from locating individual cables with the built-in tone generator
or the Remote Identifiers, to generating test documentation and
in-service troubleshooting of PoE networks.
GET FASTER RESULTS
The simple one touch autotest can be initiated either from
the main unit or from the Active Remote, saving time spent for
walking between outlets and reducing the overall working time.
When troubleshooting, all cable tests can be performed individually
to minimize fault-finding time.
WELL-EQUIPPED FOR THE CHALLENGES
OF THE FUTURE
NetXpert XG ensures a future-proof start into the new era of
high-speed qualification. The NetXpert series offers simple firm-
ware upgrades, and a license system allows for later upgrades
to add new features. There are 3 options (NetXpert 1G, NetXpert
2.5/5G and NetXpert XG). The purchase of an upgrade license
always extends the functionality of the device one step upwards.
All wear parts (e.g. RJ45 jack) can easily and conveniently
be replaced.
RJ45
Charger
Status LEDs
Micro-USB
SFP and SFP+
RJ45
Charger
Micro-USB
MAIN UNIT PORTS
ACTIVE REMOTE UNIT PORTS
To perform a network discovery test,
the main device must be connected
to a switch.
USER-FRIENDLY OPERATION
Continuity test results of all 8 wires and the shielding are
displayed in wire map format in full color, while showing cable
faults such as opens, shorts, miswires, and split pairs in a clear
and easy to understand way. NetXpert determines the cable
length and the distance to faults performing full TDR (Time
Domain Reflectometer) measurement in combination with a
capacitance measurement for increased accuracy.
The large high-resolution touch screen display facilitates work
not only in daylight but also in poor lighting conditions, while
the 7" touch screen provides sufficient space to ensure excellent
readability of the displayed test results.
The NetXpert XG generates detailed or
summarized result-reports in PDF- or CSV-
format with your company logo. The reports can
be exported from your device via a USB stick.
itnetworks.softing.com/XG