socketmobile.com SERIES 700 DURASCANTM Bluetooth Barcode Scanner Model D750 www.socketmobile.
TABLE OF CONTENTS Application Mode (MFi-SPP) Setup for Apple® iOS 22 Application Mode (SPP) • Android 17 • Windows PC 20 • Windows (Peripherals) 20 Basic Mode (HID) • Android 13 • Windows PC 14 • Windows (Peripherals) 15 Battery Charger & Battery Warning 40-44 Bluetooth Connection 25 Bluetooth Connection Modes 11 Bluetooth Unpairing 24 Command Barcodes 26 Helpful Resources 34
TABLE OF CONTENTS Optional Charging Accessories 8 Package Contents 4 Powering on/off 9 Product Information 5 Product Specifications 33 Safety, Compliance & Warranty 35-46 Scanning Barcodes 10 Status Indicators 30
PACKAGE CONTENTS DuraScan D750 Lanyard AC adapter* & USB to DC plug cable *Use the plug that is regionally appropriate Thank you for choosing Socket Mobile! Let’s get started! © 2010-2016 Socket Mobile, Inc. All rights reserved. Socket, the Socket logo, and SocketScan are registered trademarks or trademarks of Socket Mobile, Inc. The Bluetooth word mark and logo are registered trademarks of the Bluetooth SIG, Inc. USA, and any use by Socket Mobile, Inc. is under license.
PRODUCT INFORMATION Scanner head Green/Red LED Product label Bluetooth LED (Blue) Battery LED (Green/Yellow/Red) Trigger button Power button* Direct Current Lanyard Pins for charging cradle *Also used for keyboard Pop-up in Basic Mode (HID) only 5
SCANNER SETUP 1. Attach the Lanyard (optional) Detach the string loop of the tether from the lanyard. Then feed the string loop through the slot. Pull tight so the string loop is secure, reattach the string loop to the tether from the Lanyard.
CHARGE THE BATTERY 6 Hours The scanner must be fully charged before first use. Please allow 6 hours uninterrupted charging for the initial battery charge. For the Scanner, lift the rubber flap to access the power connector. • Red LED = Charging • Green LED = Fully charged Important: Charging from a computer USB port is not reliable and not recommended. Battery warning: Do not remove the pre-installed battery. The DuraScan contains a rechargable lithium-ion battery.
OPTIONAL CHARGING ACCESSORIES Charging with Cradle or QX Stand is optional (available separately). Charging Cradle QX Stand Battery charger warning: Only use the dedicated charger provided for this unit. See more battery charger warnings at pg.
POWERING ON/OFF Power button Powering On: Powering Off/ Disconnecting: Press and hold down the small power button until the LED turns blue and the scanner beeps twice (low-high). Press and hold down the small power button until the scanner beeps twice (high-low). The scanner can power off automatically if it is not connected within 5 minutes and it is connected within 2 hours of inactivity.
SCANNING BARCODES 1D Barcode Aim the scan beam straight across the entire barcode. 2D Barcode Aim at the center. Trigger button Scanning Barcodes 1. Hold the scanner a few inches from the barcode. 2. Aim, press and hold the trigger button. By default, the scanner will beep, vibrate, and the LED will flash green to confirm successful scan. Caution: Do not stare directly into the LED beam.
BLUETOOTH CONNECTION MODES Connect your scanner using one of the following Bluetooth connection modes: Bluetooth Connection Profiles Bluetooth Mode Basic Mode (HID) (Default)* Human Interface Device Profile Description • “NO” software installation needed • Connects to most devices • Good for barcodes containing small amounts of data • Scanner appears like a keyboard to host device Application Mode • Software installation required (SPP) • More efficient and reliable data communications for barcodes contain
BLUETOOTH CONNECTION MODES Operating System Connection Options Devices Bluetooth HID Support Bluetooth SPP Support Bluetooth Apple Serial Specific (MFi Mode) Android Android 2.1 & later Yes Yes N/A Apple iOS iPod, iPhone, & iPad Yes N/A Yes Windows Mobile Windows Mobile 6.x Yes Yes N/A Windows PC Windows 7, 8, 10 Yes Yes N/A Mac OS Mac OS X 10.4 to 10.
BASIC MODE Android: Connect Android Device in Basic Mode (HID) 1. Power on the scanner. Make sure the scanner is discoverable (unpaired). 2. Touch Home | Menu | Settings | Wireless & Networks | Bluetooth settings 3. Make sure the device has Bluetooth “On” and scan for devices. 4. In the list of found devices, select Socket scanner [xxxxxx]. Tap Pair. 5. The scanner will connect to the Android device. 6. The scanner will beep once after it has connected and is ready to scan barcodes.
BASIC MODE Apple: Connect Apple iOS Device or Mac OS Device Basic Mode (HID) In this mode the scanner works and behaves just like a keyboard. Therefore, scanner will work with Safari, Notes, and any other applications that supports an active cursor. 1. Power on the scanner. Make sure the scanner is discoverable (unpaired). 2. Start a Bluetooth device search. • iOS: Tap Settings | General | Bluetooth. Turn on Bluetooth. A Bluetooth device search will begin.
BASIC MODE Windows: Connect Windows PC Power on the Scanner. Make sure the Scanner is discoverable (unpaired). 1. Use your computer’s Bluetooth Settings to connect to the Scanner. 2. Open Devices and Printers and select “Add a device”. 3. In the device list, select Socket Scanner [xxxxxx]. Click Next. 4. If a passkey is requested, enter 0000 (four zeroes). Click OK. Or Pair Now. 5. Follow the remaining screens to complete the wizard.
WINDOWS BASIC MODE (PERIPHERALS) Windows: Connect Windows PC as a Basic Mode (HID) Peripheral 1. Power on the Scanner and scan this barcode. The Scanner will beep 3 times. 2. Turn on Bluetooth on your PDA or PC and start a device search. Make sure it is discoverable. 3. Select Socket Scanner. If prompted for a passkey, enter 0000 (four zeroes). If prompted to select services, select Input Device. 4. After the Scanner connects and is ready to scan barcodes, it will beep once.
APPLICATION MODE (SPP) Connect Android or Windows Mobile Device: Highly recommended, allows two-way communications with Android, Windows and Mobile Devices. SocketScan 10 software installation required. 1. Power on the Scanner and scan this barcode. The Scanner will beep 3 times. Make sure the Scanner is discoverable (unpaired). 2. Turn Bluetooth on for your device. Go to Settings > Bluetooth. A Bluetooth Devices search will begin. 3. Tap Socket Scanner[xxxxxx] in the list of Devices found.
APPLICATION MODE (SPP) Connect Android device in Application Mode (SPP) using EZ Pair 1. Go to Google Play Store, search for “SocketScan 10”. 2. Download & install. Follow the on screen instructions. Note: If prompted, allow the app to access your Bluetooth settings / USB storage / SD card / Coarse location. 3. Make sure Bluetooth is turned on. 4. Open SocketScan 10 application. 5. When prompted to set SocketScan 10 as the keyboard language, tap Back . 6.
APPLICATION MODE (SPP) Connect Android device in Application Mode (SPP) 15. Select [On screen] button. 16. On the next screen, tap on the 7Qi or 7Xi button that is appropriate for your scanner button. 17. Scan the barcode on the screen. The Scanner will beep 3 times. 18. When notified of a pairing request, swipe the notification icon down then tap Pairing request. 19. On the next screen, tap Pair. 20. The Scanner will beep once to indicate connected state and is ready to scan barcodes.
WINDOWS PC - APPLICATION MODE Connect Windows PC in Application Mode (SPP) Note: Make sure you have administrative privileges. 1. Download the latest SocketScan 10 software from Socket Mobile’s support web page. 2. Follow the on-screen instructions to install the software. 3. In SocketScan 10 Settings, select an incoming Bluetooth serial COM port. Note: If there is none please click Ports to create at least one new incoming COM port in Bluetooth settings. 4. Click Finish.
WINDOWS PC - APPLICATION MODE To pair the Scanner with the PC using EZ Pair: 1. Power on the Scanner. Make sure the Scanner is available to be connected to Bluetooth (unpaired). 2. Launch SocketScan 10 and click on the SocketScan 10 icon in the task tray. In the pop-up menu, click Socket EZ Pair. 3. Scan the barcode on the screen to switch set your scanner in Application Mode (SPP). The Scanner will beep 3 times. 4. Click 2D Scanner accordingly. 5. Scan the barcode that appears on the screen. 6.
APPLICATION MODE (MFI-SPP) Connect Apple iOS device in MFi Mode Please check with your scanner application vendor or visit www.socketmobile.com/appstore to confirm your Scanner-enabled application supports the Scanner. If you are using the Scanner with an Apple iOS device and a Scanner-enabled Application that does not provide instructions how to connect with the Scanner, please use the following steps. 1. Power on the Scanner. Make sure the Scanner is discoverable (unpaired). 2.
APPLICATION MODE (MFI-SPP) Note: The characters in brackets are the last 6 characters of the Bluetooth Adress. The full Bluetooth address is printed on the Product label. 5. Launch your Scanner-enabled Application. The Scanner will beep once indicating that it is connected to the appropriate application. Now you are ready to scan barcodes.
BLUETOOTH UNPAIRING Note: This procedure will put the Scanner in discoverable mode. Step 1: Unpairing the Scanner: Delete the Bluetooth Pairing If the Scanner is paired with a device, unpair it before trying to connect to a different device. 1. Power on the Scanner. 2. Press the trigger button then then power button and hold. 3. After you hear 3 beeps, release both buttons. The Scanner will unpair and automatically power off. The next time you power on the Scanner, it will be discoverable.
BLUETOOTH CONNECTION Automatic Reconnections Each time you power on the Scanner, it will automatically try to connect to the last device it was connected to. • Make sure the device is in range with Bluetooth On. • If using Basic Mode (HID), pressing the trigger button will force or trigger the connection. • If using Application Mode (SPP), make sure the Scanner-enabled Application is active.
COMMAND BARCODES Scan command barcode(s) to quickly configure the Scanner. Make sure the Scanner is not connected to a device before scanning a command barcode! See page 21 for unpairing instructions. For a complete set of command barcodes, download the Command Barcodes Sheet: http://www.socketmobile.com/support/downloads The web link is also provided in the below QR Code. To open the web page, scan this QR Code using a QR Code Reader App in your iOS device.
COMMAND BARCODES (CONTINUED) Important! Make sure the Scanner is not connected to a host computer or device before scanning a command barcode! Bluetooth Connection Modes Basic Mode (HID-Keyboard) (default) Configures the Scanner to Human Interface Device (HID) mode as a Keyboard class device Application Mode (SPP) Changes the Scanner to Serial Port Profile (SPP) mode Application Mode (MFi-SPP) Changes the Scanner to MFi mode for Apple iOS Devices 27
COMMAND BARCODES (CONTINUED) Important! Make sure the Scanner is not connected to a host computer or device before scanning a command barcode! Beep Settings Beep after scanner Decodes Data ON (default) Enables Scanner to beep to indicate successful scans. Beep after scanner Decodes Data OFF Disables Scanner from beeping to indicate successful scans.
COMMAND BARCODES (CONTINUED) Vibrate Settings Vibrate “ON” (default) Enables scanner to vibrate to indicate successful scans. Vibrate “OFF” Disables scanner from vibrating to indicate successful scans. Factory Default Factory Reset Revert all settings to factory defaults. The scanner will power off after scanning this barcode.
STATUS INDICATORS Status LED Activity Meaning Bluetooth 1 Blue blink every second Bluetooth is On but not connected 1 Blue blink every 3 seconds Scanner is connected to device Good Read Green Constant (while scanning) Data successfully scanned Battery Status Red Blinking (while scanning and no AC power) 20% or less battery capacity remaining Red Constant (while AC power) Battery is charging Off (no light) (while AC power) Battery is fully charged Off (no light) (while no AC power) Scanner
STATUS INDICATORS (CONTINUED) Beep Pattern Meaning Low-high tone Power On. High-low tone Power Off. 1 low beep Keyboard Pop-up Enable. 1 beep Scanner connected to device and ready to scan barcodes. 1 beep with Green LED blink Data successfully scanned. 2 beeps, same tone Scanner disconnected from device. 1 long beep Scanner tried multiple times unsuccessfully to connect to the last device it paired with. After 5 minutes the Scanner will power off.
STATUS INDICATORS (CONTINUED) Vibrate Meaning Vibrate Power On or data successfully scanned. Command Barcodes are available on pages 23-25 to modify the LED, beep, and vibrate settings. If you are using a Scanner-enabled Application, typically the application provides settings for LED, beep, and vibrate settings. Bluetooth Mode Sequence Time after powering on Scanner Bluetooth mode 0-5 minutes Discoverable and connectable 5 minutes If a connection is not made the Scanner will power off.
PRODUCT SPECIFICATIONS Specifications D750 Dimensions (L x W x H) 5.2” x 1.5” x 1.6” (132.2 x 37.1 x 40.1 mm) Total Mass 3.8 oz (108 g) Antimicrobial Antimicrobial additive in all external surfaces Operating Temp -4 to +122°F (-20 to + 50°C) Battery Life Per full charge Standby: over 30 hours Active scanning: 14,000 & 70,000 scans* *Depends on scanning situation Charge Time 6 hours fully charged Bluetooth Version Bluetooth v2.
HELPFUL RESOURCES Technical Support & Product Registration: http://support.socketmobile.com Phone: 800-279-1390 +1-510-933-3020 (worldwide) Warranty Checker: http://www.socketmobile.com/support/warranty-checker Socket Mobile Developer Program: Learn more at: http://www.socketmobile.com/developers The User’s Guide (full installation and usage instructions) and Command Barcodes (Advanced Scanner Configurations) can be download at: http://www.socketmobile.
SAFETY AND HANDLING INFORMATION WARNING: Failure to follow these safety instructions could result in fire or other injury or damage to the DuraScan D700 Series Barcode Scanners or other property. Carrying and Handling the DuraScan Barcode Scanners: The Socket Mobile barcode scanner contains sensitive components. Do not drop, disassemble, open, crush, bend, deform, puncture, shred, microwave, incinerate, paint, or insert foreign objects into this unit. Do not attempt to disassemble the product.
BLUETOOTH DEVICE UNITED STATES FCC ID: LUBD750 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
BLUETOOTH DEVICE UNITED STATES FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
BLUETOOTH DEVICE CANADA IC ID: 2925A-D750 This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
BLUETOOTH DEVICE EUROPE CE Marking & European Union Compliance Products intended for sale within the European Union are marked with a CE Mark, which indicates compliance to applicable Directives and European Normes (EN), as follows. Amendments to these Directivces or ENs are included: Normes (EN), as follows: Applicable Directives: Bluetooth Products: R&TTE Directive 1999/95EC, Low Voltage Directives 73/23/EEC and 2006/95/EC, EMC Directive 2004/108/EC.
BATTERY CHARGER BATTERY CHARGER: Charging: CAUTION: Only use the dedicated charger provided for this unit. The provided battery charger may become warm during normal use. Always allow adequate ventilation around the battery charger and use care when handling. Unplug the Charger if any of the following conditions exist: • The Charger is exposed to rain, liquid, or excessive moisture. • The Charger case has become damaged. • You suspect the Charger needs service or repair.
BATTERY WARNING STATEMENTS This device contains a rechargeable Lithium-Ion battery. Stop charging DuraScan Barcode Scanners if charging isn’t completed within the normal specified time (approx. 6 hours). Stop charging the battery if the DuraScan Barcode Scanner case becomes abnormally hot, or shows signs of odor, discoloration, deformation, or abnormal conditions is detected during use, charge, or storage.
BATTERY WARNING STATEMENTS • Dispose of used batteries in accordance with the prevailing community regulations that apply to the disposal of batteries. • Never expose this product or the battery to any liquids. • Do not shock the battery by dropping it or throwing it. If this unit shows any type of damage, such as bulging, swelling or disfigurement, discontinue use and promptly dispose. Product Disposal Your device should not be placed in municipal waste.
LASER AND LED DEVICES Caution: DO NOT STARE DIRECTLY INTO THE LED BEAM. LED DEVICE: The DuraScan D700 and D750 contain a LED-type scan engine. For the Class 1 LED version of this engine, the following applies: • Complies with IEC 60825-1:2001-08, and EN 60825-1:1994 + A1 + A2 • LED output is in the 630-670nm range (visible red). • Class 1 LED devices are not considered to be hazardous when used for their intended purpose.
REGULATORY COMPLIANCE CE MARKING AND EUROPEAN UNION COMPLIANCE Testing for compliance to CE requirements was performed by an independent laboratory. The unit under test was found compliant with all the applicable Directives, 2004/108/EC and 2006/95/EC. WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT The WEEE directive places an obligation on all EU-based manufacturers and importers to take-back electronic products at the end of their useful life.
LIMITED WARRANTY Socket Mobile Incorporated (Socket) warrants this product against defects in material and workmanship, under normal use and service, for one (1) year from the date of purchase. Product must be purchased new from a Socket Authorized Distributor or Reseller. Used products and products purchased through non-authorized channels are not eligible for this warranty support. Warranty benefits are in addition to rights provided under local consumer laws.
Extend Your Warranty... Receive Priority Service and Personal Care. You have 60 Days from purchase date to enroll in a SocketCare Service Program! For detailed information visit: http://www.socketmobile.
