BTM4KC Manual BTM4KC KwikBlue4c Class 1 BC04 Bluetooth Module with 20-pin connector ( 8520-00145 ) Manual 8 Mbit Memory, UART Interface Bluetooth 2.0 + EDR Revision 0.1 July 29, 2008 July 29, 2008 Document#: AboCom CONFIDENTIAL Page 1 Revision 0.
BTM4KC Manual Reproduction of the contents of this manual without the permission of AboCom System is expressly prohibited. Please be aware that the product described in this manual may change without notice. This manual has been prepared with the greatest care regarding its contents. However, in the event that it contains omissions, errors or any other misinformation, please feel free to direct comments to: http://www.abocom.com.tw/for the details.
BTM4KC Manual Copyright and Trademarks The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Socket Communications is under license. July 29, 2008 Document#: AboCom CONFIDENTIAL Page 3 Revision 0.
BTM4KC Manual Table of Contents 1.1 Purpose and Scope of Document ................................................................................................. 5 1.2 Product Overview ....................................................................................................................... 5 2. Standard Operating Conditions........................................................................................................ 5 3. Features List .............................................
BTM4KC Manual 1. General 1.1 Purpose and Scope of Document This document describes a radio device incorporating Bluetooth® wireless technology known as a Bluetooth Class 1 BC04 module. The Bluetooth module complies with the “Specification of the Bluetooth System,” version 2.0 + EDR. This document describes the General design guideline for the Bluetooth module. 1.
BTM4KC Manual 3. Features List Features Values Power Level Basic Rate : +12 dBm Max. EDR rate : -2 dBm Max. Program Memory 8 Mbits (512k x 16 bits) Flash RAM 32k bytes x 16 bits Reference Oscillator Built-in Sub Clock Oscillator Built-in Audio Interface PCM A-Law, µ-Law (CVSD) Serial Data Interface UART (BCSP of H:4) Physical Dimension 14mm X 39mm Physical Connection Board-to-board connector – 20PIN 10X2-0.5mm (Panasonic AXK6F20347YG) 3.
BTM4KC Manual 3.2 Hardware Pin-assign Please reference the following pin-assignment for your application development. July 29, 2008 Document#: AboCom CONFIDENTIAL Page 7 Revision 0.
BTM4KC Manual 3.3 RESET Sequence RESET is asserted by module itself, the external reset circuit is not required. 3.4 UART (Universal Asynchronous Receiver Transmitter) UART_TX, UART_RX, UART_RTS, UART_CTS form a conventional asynchronous data serial port. The interface is designed to operate correctly when connected to other UART devices such as the NS16550A. The signaling levels are 0V and VCC.
BTM4KC Manual 4. Software Specifications The Bluetooth module contains the Bluetooth protocol stack (firmware) HCI (Host Controller Interface) compliant with the “Specification of the Bluetooth System,” version 2.0+EDR. 4.1 Software Architecture The following figure shows typical implementation example of Bluetooth protocol stack using the Bluetooth module. As shown in this figure, a Bluetooth protocol stack over HCI is required to complete the full Bluetooth functionality.
BTM4KC Manual 5. Application Note 5.1 Layout guideline 5.1.1 please follow the footprint of module. 5.1.2 Don’t put coppor foil or any trace under the antenna area. 5.1.3 Add a power de-coupling circuit for 3.3V and PA3.3V. 5.1.4 Suggest to take coppor foil or any trace away from the near side with our module. 5.2 Power source 5.2.1 Suggest to use a LDO regulator to convert your power into 3.3V for our module. July 29, 2008 Document#: AboCom CONFIDENTIAL Page 10 Revision 0.
BTM4KC Manual Appendix 1 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
BTM4KC Manual Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Appendix 2 Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules.
