Operator`s manual
2
14. Maintain tools with care – Keep cutting edges sharp
and clean for best performance and to reduce the
risk of injury. Follow instructions for lubricating and
changing accessories. Inspect the trimmer periodically
and replace if damaged. Repair the trimmer only at an
authorized service facility. Keep handles dry, clean,
and free from oil and grease.
15. Checked for damaged parts – Before continuing to
use the trimmer, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for the alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any
other condition that may affect the trimmer’s operation.
A guard or other part that is damaged should be
properly repaired or replaced by an authorized service
center unless indicated elsewhere in this manual.
c) ADDITIONAL SAFETY INSTRUCTIONS FOR GRASS
TRIMMER/EDGER
1. Keep guards in place and in working order.
2. Keep hands and feet away from the cutting area.
mCAUTION!
The safety guard is critical to the safety of the operator and the
safety of people standing within a safe distance of the trimmer.
The safety guard keeps the trimmer in good working order and
must always be in place during operation.
• Do not try to stop the cutting device (nylon line) with your
hands. Always let it come to a stop by itself.
mWARNING! After switching off the tool, the cutting device
continues to rotate for a few seconds.
• Only use the original type of nylon line. Do not under any
circumstances use metal line instead of nylon line.
• Do not use the tool to cut grass which is not on the ground.
For example, do not cut grass growing on walls or rocks.
• Do not switch on the tool in an enclosed or poorly ventilated
space or in the presence of ammable and/or explosive
substances such as liquids, gases and powders.
• Only cut during broad daylight or with adequate articial
light.
• Check that all grass cuttings and dirt have been removed
from the ventilation vents.
• Do not cross roads or gravel paths while the tool is still
running.
• When the tool is not in use, store it in a dry place and out of
reach of children.
• After use, disconnect the tool from the power supply and
check for damage. If you have the slightest doubt about the
condition of the tool, contact an authorized service center.
• Only use the tool according to the instructions given in this
manual.
• Check regularly that the screws are tight.
• Do not try to repair the tool or access internal parts.
Contact an authorized service center.
Extension Cords
• Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough
to carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss of
power and overheating. Table 1 shows the correct size
to use depending on cord length and nameplate Ampere
rating. If in doubt, use the next heavier gauge. The smaller
the gauge number, the heavier the cord.
• Ground Fault Circuit Interrupter (GFCI) protection should
be provided on the circuits or outlets to be used for this
electric trimmer. Receptacles are available with built-in
GFCI protection and may be used for this measure of
safety.
• Use only UL listed extension cords. Inspect the extension
cord before use and never use damaged or altered
extension cords. Follow the extension cord manufacturer’s
safety instructions.
• To prevent the appliance cord from disconnecting from the
extension cord during operation, use the plug-receptacle
retaining straps provided or make a knot with the two cords
as shown in Table 2.
Table 1. Minimum Recommended Extension Cord Gauge
(AWG) Chart
Table 2. Method of securing Extension Cord
25
18
18
16
14
50
16
16
16
12
100
16
14
14
150
14
12
12
Volts
120V
0 – 6
6 – 10
10 – 12
12 – 16
Total length of cord in feet
AWG
(Extension Cord Gauge)
Not Recommended
Ampere Rating
(B) Connect plug and receptacle
Cord set Appliance cord
(A) Tie cord as shown