Replacement Part List

ManualsBrandsSnow Joe ManualsOutdoor Power EquipmentReplacement Auger/Snow Impeller for 322/322P Snow Shovels

SAVE THESE INSTRUCTIONS

OPERATOR’S MANUAL

Form No. 7322P-880E

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

Any electrical appliance can be dangerous if used incorrectly.

Some of the safety precautions given in this manual apply

generally to many appliances. Other warnings are specic to

the use of this snow thrower.

General Safety WARNINGS!

You and any other operator of this snow thrower must read,

understand and follow these instructions in their entirety, and

should re-read them at the start of each snow season. Failure

to follow these instructions may result in ELECTRIC SHOCK,

FIRE and/or serious PERSONAL INJURY.

Notice the personal safety alert symbol

m used in this

manual to draw your attention to a WARNING given along

with the particular operating instruction. This means that

the operation requires special ATTENTION, CAUTION, and

AWARENESS.

1. Keep children, pets, and others away from the work

area: Be aware that the normal noise of the machine

when turned on may make it difcult for you to hear

approaching people.

2. Use the electric cord and extension cord safely:

A. Keep cord away from heat sources and sharp objects.

B. Prevent oil or other uids from spilling onto snow

thrower or cord.

C. Never carry the snow thrower by cord or yank it to

disconnect from electrical outlet. Keep cord away from

heat, oil, and sharp edges.

D. Replace or properly repair damaged cords. If cord

is damaged in any manner while plugged in, pull

extension cord from wall receptacle.

E. Extension Cord: WARNING – Only use a UL rated

extension cord for OUTDOOR, all-weather use

(usually orange color). To prevent the disconnection

of the snow thrower from the extension cord during

operation, make a knot as shown on page 5; see

WARNING box on page 5 for more cord information.

3. Wear proper clothing: Wearing rubber boots offers

additional protection from electric shock when operating

this snow thrower. Do not wear loose clothing that may

become caught in the machine.

4. Moving parts present risks: Keep hands away from

moving parts. Guards must be properly placed to protect

operator. Shut off and disconnect cord before touching

any parts other than the handles and switch.

5. Hand-held operating position: Operating this

snowthrower in the hand held position is unsafe.

6. Surfaces: This snow thrower is intended for use on paved

surfaces. The unit should not be used on gravel or stone

surfaces.

7. Unintentional operation: Do not carry plugged-in snow

thrower with nger on switch. Be sure that the switch is off

when plugging in.

8. Body position: Be aware of your footing and body

positioning to maintain proper balance at all times; watch

for uneven surfaces and don’t overreach.

9. Excessive force: The snow thrower was designed to

respond at a certain rate for various snow conditions for

optimum safety and performance. Don’t force it; keep

pressure constant.

10. Hitting an object: If the snow thrower accidentally strikes

an object, rst stop; remove key then plug. Inspect for

damage; repair or replace part before using the snow

thrower again.

11. When work is completed: Disconnect from the power

source when not in use, when changing accessories, and

before performing any maintenance function.

12. Store safely: Store indoors in a dry area between uses.

Store in a locked area, where children and unauthorized

people cannot gain access.

13. Maintain for safety and longevity: See instructions in

this operator’s manual for proper maintenance. Use only

those replacement parts made for your model.

14. The use of any other accessory or attachment might

increase the risk of injury.

A Division of Snow Joe, LLC

Snow Thrower

Model No. 322P

Snow Thrower

Summary of content (8 pages)

PAGE 1
Snow Thrower Model No. 322P Form No. 7322P-880E OPERATOR’S MANUAL A Division of Snow Joe, LLC 4. Moving parts present risks: Keep hands away from moving parts. Guards must be properly placed to protect operator. Shut off and disconnect cord before touching any parts other than the handles and switch. 5. Hand-held operating position: Operating this snowthrower in the hand held position is unsafe. 6. Surfaces: This snow thrower is intended for use on paved surfaces.
PAGE 2
Safety and Instruction Decals m Safety decals and instructions are easily visible to the operator and are located near areas of potential danger. Lost or damaged decals should be replaced. TO OPERATE INSERT KEY DEPRESS BAR W A R N I N G ! ¡ADVERTENCIA! MISE EN GARDE! Electric shock can cause serious injury or death. To avoid electric shock: REMOVE SHIPPING PIN ABOVE BEFORE REMOVING THIS LABEL AND ATTEMPTING TO SEPARATE TUBES. DO NOT USE SNOW THROWER IF WIRE INSULATION INSIDE OF TUBE IS DAMAGED.
PAGE 3
2. Slide the lower tube (B) into the upper tube (A) (Figure 2). Assembly m CAUTION Note: Before you connect the tubes, you may find it easier to remove the slack in the wire. Slightly pull the wire from the bottom of the lower tube (B) before you join the tubes together. m Inspect wiring, which, if damaged during shipping, may cause serious bodily injury during equipment use. If any damage is seen or suspected, do not assemble.
PAGE 4
Power Base Assembly 3. After sliding lower tube (B) inside the upper tube (A), line up the screw holes on each tube (Figure 3). 1. Position the power base (G) beneath the handle support (H) as shown in Figure 5-2. A H Figure 5-1 C F G B D Figure 3 A. Upper tube B. Lower tube C. Slotted screw D. Countersunk nut Figure 5-2 I 4. Locate in the Parts Bag the slotted screw (C) and the countersunk nut (D).
PAGE 5
To prevent the snow thrower cord and extension cord from disconnecting during use, tie the extension cord into a loose knot around the lower bar (K) of the handle as shown in next step (Figure 7, Item O). Operation NOTE: It is best to remove snow before it becomes packed down. m WARNING 2. Plug the extension cord into a wall outlet. Insert the key (L) into the slot in front of the hand-grip (M) (Figure 7). m M L Electric shock may cause SEVERE INJURY or DEATH.
PAGE 6
Maintenance Operating Procedures 1. Turn on the snow thrower switch: With key inserted, squeeze on/off switch to power on. Position the appliance so that the blade makes level contact with the ground, by titling it slightly forward (away from you). When starting in deep snow, see suggestion below. m m WARNING Risk of Serious Bodily Injury: 2. Begin to push the snow thrower forward: Do not rush.
PAGE 7
Note: You may need to pull out the rotor using both hands. Please wear gloves to prevent injury. 2. Using an open end wrench, loosen the nut between the body and the rotor (counterclockwise). Hold the loosened nut and turn the outer body bolt counterclockwise. Remove nut, bolt, and washers (Figure 9). 4. Install the new rotor reversing the above steps. Storage CAUTION: Store electrical appliances in a locked area away from children and unauthorized users. C 1.
PAGE 8
A Two-Year Full Warranty for residential use in the United States and Canada General Conditions: Snow Joe, LLC warrants this product to the original purchaser for two years against defects in material or workmanship when used for normal residential purposes. Snow Joe, LLC will repair any defect in material or workmanship, and repair or replace any defective part, subject to the conditions, limitations, and exclusions set forth herein.