USER GUIDE
Safety Information Please read the following safety information carefully. The information is provided to prevent potential injury or damage. Classification (Degree of Danger) Warning Failure to follow these safety warnings could lead to a serious injury or death. Caution Failure to follow these cautions could lead to an injury or cause loss of property. Warning Do not disassemble, repair, or modify the product. Do not operate the product while driving.
Safety Information Use only the supplied power cable and windscreen bracket. Do not expose the device to liquids. Do not modify the supplied power cable and/or windscreen bracket. Do not install the product in an area which is susceptible to moisture or dust. Do not install product where it will obstruct your field of vision. Do not install the device an an area which may affect the safe operation of the vehicle controls or safety equipment e.g area where Air Bags may be deployed.
Safety Information Caution SanDisk 4GB Do not use a sharp object to operate the buttons. SanDisk SanDisk 4GB 4GB SanDisk 4GB Do not attach any stickers or paint on the device or memory card. SanDisk 4GB Do not drop device. This can damage the product or lead to a product breakdown. Do not place the device near a magnet or areas of high magnetic fields.
기 Safety Information Preserving Data on the SD Memory Card Please pay attention to following장소에 information minimize possibility본 of losing recording data. 기기를 사용할 포장을 평평한 내려놓고 장소에 벗겨낸 바닥이나 본 후다음 사용할 기기를 평평한 내려놓고 바닥이나 본to다음 사용할 기기를the장소에 내려놓고 다음 기기를 내려놓고 다음 The manufacturer is not responsible for missing data or defects caused by the user’s mishandling. 을아야 부속품이 있는지 경우 제품을 확인해 빠져있을 만약 구입한 보아야 경우 합니다. 제품을 빠져있을 만약 구입한 경우 구입한 경우 제품을 구입한 • 합니다.
Safety Information GPS Usage Please pay attention to following information to properly understand the GPS system. • If the product has not been turned on for a long time (over 3 days) or if the vehicle is in motion, it may take longer for the device to establish a GPS connection. • The GPS reception can be weakened by heavy rain. • The GPS reception can be affected when travelling through a tunnel or into an area with numerous high rise buildings.
TABLE OF CONTENTS Product Features Product and Accessories Part Name and Description DVR-1 Installation and Setup 8 19 Software Installation 19 Operating the Classic Viewer 20 Player Controls 23 11 Playback Buttons 24 11 Configuration Menu 25 SD Memory Card Folder Details 26 Firmware Upgrade 27 10 12 Caution before installation 12 Installation of the Recorder 13 Operational Instructions Classic Viewer Software Product Specification and Certification 16 Recording Modes 16 Tabl
Product Features 0.3 Mega Pixel High Quality Sensor Acceleration Information Retention • Uses a 0.3 mega pixel high quality image sensor to provide clear and vivid images. • It saves vibration information from the frontrear and left-right of the car at the moment of an accident, extreme acceleration, breaking or turning. Multiple Recording Modes (Continuous, Event and Manual Recording) GPS • It continuously records 30 frames per second at a 120º angle within the driving direction at high quality.
Product Features Easy viewing of recorded images by a designated player Audio Input • It records driving images and audio data simultaneously by using an internal microphone. • Recorded images in SD memory card can be viewed by a designated player on a computer. Video Output Day/Night Recognition • It provides Real-time image output which can be displayed through a navigation unit or external AV device. • It provides a high quality image created by precise technology even in low light situations.
Product and Accessories 구성품 확인하기 확인하기 성품 확인하기 구성품 확인하기 제품을 구입하셨을 때 먼저 포장을 벗겨낸 후 평평한 바닥이나 사용할 장소에 본 기기를 내려놓고 다음 Please make the following components are included when you 본 unpack the본 product. If 내려놓고 any of 제품을 the following items are 하셨을 때 먼저 포장을 벗겨낸 후 평평한 사용할 장소에 기기를 내려놓고 다음 을 구입하셨을 때 sure 먼저 포장을 벗겨낸 후바닥이나 평평한 바닥이나 사용할 장소에 기기를 다음 과제품을 같은 부속품이 모두 들어 있는지 확인해 보아야 합니다. 만약 부속품이 빠져있을 경우 구입한 구입하셨을 때 먼저 포장을 벗겨낸 후 평평한 바닥이나 사용할 장소에 본 기기를 내려놓고 다음 missing, contact your local dealer.
1.
2. Installation and Setup 2-1 Caution before installation Parts • Make sure all components are included before starting installation. (See Page 10: Product and Accessories) • If you find any components are missing, contact your dealer. Installation Preparation Please adhere closely to the following instructions as the installation angle/position can affect the recording. 1 2 3 Position the bracket in a central area of the windshield.
2. Installation and Setup 2-2 Installation of the Recorder Check location and installation conditions of the recorder. If you have not already done so then please refer to Cautions before installation. (See Page 2: Safety Information) Remember that a120º angle can be recorded with the recorder installed at the top, bottom or center of the windshield. 1 Clean the windshield with dry fabric where the holder will be positioned. 2 Remove the protective film from the double-sided tape.
2. Installation and Setup <2-2 Installation of the Recorder> ETK 4GB SanD isk 4GB 4 SD Memory card preparation - Make sure the side with letters is facing upwards. 5 Insert the SD Memory card into the card slot of the recorder. - Make sure SD memory card is properly seated in slot. 6 Connect the power cable to the power input on the recorder. 8 Place the recorder onto the bracket.
2. Installation and Setup <2-2 Installation of the Recorder> 10 Connect the other end of the power cable to the car power out. An alarm sound will be activated if the SD Memory card is not inserted correctly. A hardware cable is also supplied with the device, this allows the unit to be connected directly to the vehicle wiring. Connections: Red (with fuse Blue Positive supply Negative or vehicle chassis. If in doubt please consult an Auto Electrician before connecting this device to the vehicle wiring.
3. Operational Instructions 3-1 Recording Modes REC REC CAMERA RECREC RECREC MIC CAMERA MIC 4 Connecting Power - A blue light flashes on the LED when the power is connected. Manual Recording - The user can manually start recording by pressing REC button for an emergency or a situation which needs to be recorded. CAMERA RECREC MIC CAMERA MIC 1 REC CAMERA 2 5 MIC MIC MIC MIC Starting Recording - When the light is solid blue the device is ready for continuous recording.
3.
3. Operational Instructions 3-3 Removing the SD Memory Card Please use the following steps to remove the SD Memory Card. Failure to do so may cause permanent damage to the data. 1 2 3 4 Turn off your car and remove the power cable from the unit. Wait until the LED on the body turns off (The LED will turn off slowly). It may take 5~10 seconds. Gently push SD memory card inward and it will trigger a release. Remove the SD memory card.
4. Classic Viewer Software 4-1 Software Installation The user can playback recorded video through the video player with a compatible computer. Windows XP, Vista and 7. C S-MM MC/R SD/M USB 2.0 isk SanD 4GB 1 Connect the SD memory card to a computer. -C ombine the SD memory card with USB gender and connect the USB gender to a computer. 2 3 Double-click snooper.exe on the SD memory card or download the latest program from the download menu at www.snooperneo.co.
4. Classic Viewer Software 4-2 Operating the Classic Viewer 1 Running the software - Double-click the Snooper icon from the desktop or. (File name : Snooper Viewer.exe ) 2 The player software screen will then appear. 20 3 Opening a recording video file - Click the USB button and select a saved recording on SD memory card. Select the time folders within the “xxxx_EVENT” or “xxxx_REC” folders.
4. Classic Viewer Software <4-2. Operating the Classic Viewer> 4 5 Video Display - The first video from the selected folder will be displayed on the screen. 21 Playing the Video - Press to begin the video.
4. Classic Viewer Software <4-2. Operating the Classic Viewer> Google Map Control Control Top, Bottom Z 1. Axis X: Red 2. Axis Y: Yellow 3. Axis Z: Green Description Street View Use to enlarge, reduce the map size REC BUIL LS-I MIC X Front, Rear 6 General map View Y Left, Right Satellite map view 7 File List - Press to display the file list. Select any file within the list to begin playing. (The files are created in intervals of 30 seconds.
4.
4.
4. Classic Viewer Software 4-5 Configuration Menu The user can change the settings for the recorder in the configuration menu. Press this button and the configuration window will open. Drive : Select the drive location of the SD memory card. Video Quality : Set the recording quality for the device. Video Frame Rate : Set the recording frame rate for the device. Sound Volume : Set the volume for audio recording. Shock Sensitivity : Set sensitivity of the G-sensor. Speed Unit : Select speed unit type.
4. Classic Viewer Software 4-6 SD Memory Card Folder Details Folder Name Description This folder holds the data for the various event recordings. “[Model Name]_EVENT” Data format - EVS_”Time” : Sensor Recording Files - EVK_”Time” : Manual Recording Files This folder holds the data for the continuous recording. “[Model Name]_REC” Data format - REC_”Time” : Continuous Recording Files This folder holds the configuration details of the device. “setting” “UPDATE” Configuration File List - setDST.
4. Classic Viewer Software 4-7 Firmware Upgrade 1 2 3 4 Connect SD memory card to a computer. Create a folder named “Update” on SD memory card. Copy the firmware(file name: "[Model Name]"_Date.BIN) into the “UPDATE” folder. (File name example : B2000_201112.BIN ) Connect SD memory card to the unit body and power on. The upgrade will be completed as indicated by LED color changing; blue(blink) red violet blue(blink) and single buzzer sound confirms completion.
5.
5. Product Specification and Certification 5-2 Certificates • CE : Industrial Safety, Europe • FCC : Federal Communications Commission, U.
6. FAQ : Frequently Asked Questions If your product does not work properly, please check the followings points before contacting your nearest service center. Symptoms Data is not stored properly onto the SD memory card. The device does not recognize the memory card. Solution • Remove and reinsert the SD memory card. • Then try formatting SD memory card. • Then try replacing the old SD memory card to a new one.
www.snooper.co.uk A wholly owned subsidiary of Cobra Electronics UK Ltd Like us at snooperuk Follow us @ snooperuk Performance Products Ltd, Cleaver House, Sarus Court, Manor Park, Runcorn WA7 1UL.
