Safety Instructions & Operator’s Manual for YARD CRUISER HYDRO DRIVE SERIES 1 & 2 MODELS YZ13331BE YZ13381BE YZ145332BE YZ145382BE MODEL NUMBER EXPLANATION Y Z 13 33 1 B MODEL DESIGNATION DRIVE SYSTEM TYPE ENGINE HORSE POWER CUTTING WIDTH Y – Yard Cruiser Z – Zero Turning Radius 13 - 13.0 HP Engine 145 - 14.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine.
IMPORTANT SAFETY INSTRUCTIONS PREPARATION OPERATION (Continued From Previous Page) 4. Handle fuel with extra care. Fuels are flammable and vapors are explosive. Use only an approved fuel container. Never remove fuel cap or add fuel with engine running. Add fuel outdoors only with engine stopped and cool. Clean spilled fuel from machine. DO NOT smoke. 5. Practice operation of machine with BLADE OFF to learn controls and develop skills. 6.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS.......................................................... 2-3 TABLE OF CONTENTS ...................................................................................... 4 SECTION 1 - FAMILIARIZATION ....................................................................... 5 SECTION 2 - OPERATING INSTRUCTIONS................................................... 6-9 Pre-start Checklist ...................................................................................
Section 1 - FAMILIARIZATION ENGINE SPEED CONTROL JOYSTICK CONTROL HANDLE KEY SWITCH BLADE SWITCH OPERATOR’S SEAT BRAKE RELEASE BUTTON FUEL TANK LEFT CONSOLE VIEW RIGHT CONSOLE VIEW PARKING BRAKE DECK DISCHARGE FRAME COVER DECK LIFT HANDLE FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operator’s of the SNAPPER YARD CRUISER.
Section 2 - OPERATING INSTRUCTIONS 2.1.5. Clean exterior surfaces of cutting deck and engine of any accumulation of dirt, grass, oil, etc. Keep engine air intake screen and cooling fins clear at all times. 2.1.6. Add fuel to tank of the YARD CRUISER outside where fumes can safely dissipate. Make sure fuel filler cap is tight and vent is open after refueling. See Figure 2.3. Refer to engine owner’s manual for fuel specifications. 2.
Section 2 - OPERATING INSTRUCTIONS IMPORTANT: To roll the machine without the engine running, pressure within the hydraulic pumps must be released. Tilt seat up and move control lever down to release pressure. NOTE: Control lever must be in the “UP” position to drive machine. See Figure 2.4.
Section 2 - OPERATING INSTRUCTIONS 2.2.3. MOWER BLADE 1. With engine running, move engine speed control to the Rabbit or “fast” position. 2. Pull the blade switch out into the “ON” position to engage the mower blades. See Figure 2.7. WARNING Before leaving the Riding Mower, push blade switch in to the “OFF” position to STOP blade, move joystick to neutral and engage the parking brake. Turn key switch to the OFF position. Remove key. DISENGAGE PARKING BRAKE 2.3.2. WHEEL DRIVE 1.
Section 2 - OPERATING INSTRUCTIONS 2.3.5. CUTTING HEIGHT ADJUSTMENT This machine has seven different cutting height positions. IMPORTANT: When positioning the cutting deck into a higher cutting position, pull up on the deck lift handle only, it is not necessary to pull up on the release lever at the same time. Use the release lever when moving deck cutting height to a lower cutting position. WARNING Never park the YARD CRUISER on an incline or embankment. 1. Grasp both handles together to disengage latch.
Section 3 - MAINTENANCE 3.2.2. CHECK MOWER BLADE 1. Make sure fuel cap is on tight. Turn fuel shut off valve (If equipped) to the “CLOSED” position. Start engine and allow it to run until engine runs out of fuel. Close vent on fuel filler cap. See Figure 2.3, Page 6. 2. Apply parking brake. 3. Turn key to “OFF” position and remove key from ignition switch. 3.1 INTRODUCTION To retain the quality of the YARD CRUISER, use genuine SNAPPER replacement parts only.
Section 3 - MAINTENANCE 3.3 AFTER EVERY 25 OPERATING HOURS 3.3.1. ENGINE 1. Engine Cooling System The engine cooling system consists of an engine shroud and engine fins. These should be kept clean and free of debris as needed or cleaned. 2. Engine Oil Change engine oil. See Section on CHANGE ENGINE OIL. Refer to engine owner’s manual for oil specifications. 3. Oil Filter Change engine oil filter. Refer to engine owner’s manual for filter specifications. 4.
Section 3 - MAINTENANCE 2. Front Caster Wheel Pivot Shaft The front frame cover will not have to be removed to lubricate the pivot shaft. The access hole is at the rear of the front structure underneath frame cover. a. The pivot shaft grease fitting can be accessed through a hole at the rear of the front structure. Lubricate pivot shaft with three shots of general purpose grease from grease gun. See Figure 3.6. 3.3.2. MOWER COMPONENTS (Continued) 5. Mower Blade Spindle - Lubrication a.
Section 3 - MAINTENANCE 3.4 ANNUALLY (END OF EACH SEASON) Perform all maintenance as described in the maintenance schedule. 3.4.1. Engine Service engine according to engine owner’s manual. 3.4.2. Air Filter Refer to engine instructions. owner’s manual for service 3.4.3. Oil Filter Refer to engine instructions. owner’s manual for service 3.4.4. Engine Oil Refer to engine instructions. owner’s manual for service 3.
Section 4 - ADJUSTMENTS & REPAIR 4.2 ENGINE ADJUSTMENTS & REPAIR Refer to the engine owner’s manual for those adjustments and/or repairs that can be made by the owner. WARNING Before attempting any adjustments or repairs, STOP the engine, remove the key, remove the spark plug wire(s) from the spark plug(s) and secure wire(s) away from plug(s). 4.3 MOWER DECK & COMPONENT ADJUSTMENTS The following mower deck and component adjustments and repairs can be made by the owner.
Section 4 - ADJUSTMENTS & REPAIR 4.3.2. MOWER DRIVE BELT REPLACEMENT Inspect mower drive belt. Replace belt if signs of excessive wear and/or damage are present. BELT REPLACEMENTS Engine to Hydro Pumps (All Models) Part No. 4-1823 Engine to Electric Clutch (All Models) Part No. 2-9117 Electric Clutch to Mower (33” Decks) Part No. 3-5389 Electric Clutch to Mower (38” Decks) Part No.
Section 4 - ADJUSTMENTS & REPAIR WARNING JACKSCREWS Before attempting any adjustments or repairs, STOP the engine, remove the key, remove the spark plug wire(s) from the spark plug(s) and secure wire(s) away from plug(s). 4.3.6. ADJUSTING MOWER BLADE The straightness of the mower blade(s) is essential for smooth, even mowing. Adjust blade straightness as follows. NOTE: Follow Steps 1 thru 4 for all deck sizes. 1. Make sure fuel cap is on tight.
Section 4 - ADJUSTMENTS & REPAIR WARNING Before attempting any adjustments or repairs, STOP the engine, remove the key, remove the spark plug wire(s) from the spark plug(s) and secure wire(s) away from plug(s). 4.3.7. MOWER DECK ADJUSTMENT (LEVELNESS) Side-To-Side (33” & 38” Decks) Before making deck leveling adjustments, check the tire pressure. Check tires and add or release air as needed to bring pressure to 12 psi in front and 12 psi in rear tires.
Section 4 - ADJUSTMENTS & REPAIR WARNING Before attempting any adjustments or repairs, STOP the engine, remove the key, remove the spark plug wire(s) from the spark plug(s) and secure wire(s) away from plug(s). 4.3.8. MOWER DECK ADJUSTMENT (LEVELNESS) Front to Rear Deck Pitch (33” Deck) With the YARD CRUISER on a smooth, level surface, rotate blade until blade tips are at front and rear of deck. Measure the distance from blade tips to floor.
Section 4 - ADJUSTMENTS & REPAIR 4.4.2. BLADE SHARPENING 1. Make sure fuel cap is on tight. Turn fuel shut off valve (If equipped) to the “CLOSED” position. Start engine and allow it to run until engine runs out of fuel. Close vent on fuel filler cap. See Figure 2.3, Page 6. 2. Remove key from ignition switch. 3. Remove spark plug wire(s) and secure away from spark plug(s). 4. Carefully stand YARD CRUISER on rear bumper. 5. Remove blade(s). See Figure 4.15. 6. Inspect condition of blade. Refer to Figure 4.
Section 4 - ADJUSTMENTS & REPAIR WARNING WARNING Before attempting any adjustments or repairs, STOP the engine, remove the key, remove the spark plug wire(s) from the spark plug(s) and secure wire(s) away from plug(s). Never attempt to service or charge the battery while it is installed on the YARD CRUISER. Shield the positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal which could cause sparks.
Section 4 - ADJUSTMENTS & REPAIR IMPORTANT: 3/16” above cell plates is the recommended level. However do not try to measure this dimension. Never place anything in battery other than specified electrolyte. 4.5.5. BATTERY TESTING There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the simplest and most commonly used. An unloaded test is made on a battery without discharging current.
TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Starter Will Not Crank 1. Battery dead. Engine 2. Blown fuse. 3. Electrical connections loose or corroded. 4. Defective ignition switch. 5. Blade engagement switch in the “ON” position. 6. Park brake not engaged. 7. Faulty parking brake, blade or ignition switch. 8. Faulty engine starter. 9. Faulty starter solenoid 1. Service battery. 2. Replace fuse. 3. Clean and check connections for good contact. 4. Contact authorized SNAPPER dealer. 5.
TROUBLESHOOTING PROBLEM Excessive Vibration PROBABLE CAUSE CORRECTIVE ACTION 1. Damaged, out of balance or bent mower blades. 2. Loose blade components. 3. Loose or missing air lift (if equipped). 4. Lumpy or frayed belt 5. Bent Idler, stationary or spindle pulley Rider Will Not Move Or 1. Joystick in the neutral “N” position. 2. Roll release lever is in “ROLL” position. Loss Of Traction 3. Low transmission hydraulic oil level. 4. Parking Brake engaged. 5.
SERVICE SCHEDULE SERVICE PERFORMED ITEM Engine Oil REF. Check Oil Level Page 6 Initial Oil Change Page 10 Periodic Oil Change Page 11 Initial Oil Change EACH USE X 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON X X* Air Pre-Cleaner Clean Sponge Element Engine Manual & Page 10 Engine Manual & Page 10 Engine Manual. Air Cleaner Clean or Replace Engine Manual. Spark Plug Replace Engine Manual. X Fuel Filter Replace Engine Manual.
3 YEAR LIMITED WARRANTY For three (3) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
PRIMARY MAINTENANCE 26
PRIMARY MAINTENANCE 27
PRIMARY MAINTENANCE 28
PRIMARY MAINTENANCE 29
SERVICE NOTES ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ________________________
SERVICE NOTES ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ________________________
Safety Instructions & Operator’s Manual for YARD CRUISER HYDRO DRIVE SERIES 1 & 2 WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. COPYRIGHT © 1999 SNAPPER INC. ALL RIGHTS RESERVED (REV. 2, 3/13/00) 32 MANUAL No.
