OPERATOR’S MANUAL Coronet / 2400 / RE 200 Series 13HP Hydro Riders 30” Mower Decks Mfg. No. 1694610 1694612 1694613 1694614 1694615 1694616 1695508 1695509 2690244 2690246 2690247 2690248 2690249 2690250 2690800 2690801 Mfg. No.
THIS PAGE INTENTIONALLY BLANK (FOR PLACEMENT ONLY - DO NOT PRINT) 2
Table of Contents Safety Rules & Information.................................4 Identification Numbers........................................9 Safety Decals .....................................................10 Features & Controls ..........................................12 Troubleshooting, Adjustments & Service .......25 Troubleshooting the Rider.....................................25 Troubleshooting the Mower ..................................26 Seat Adjustment.........................................
Safety Rules & Information Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety. Power equipment is only as safe as the operator. If it is misused, or not properly maintained, it can be dangerous! Remember, you are responsible for your safety and that of those around you. Use common sense, and think through what you are doing.
Safety Rules and Information Slope Operation You could be seriously injured or even killed if you use this unit on too steep an incline. Using the unit on a slope that is too steep or where you don’t have adequate traction can cause you to lose control or roll over. A good rule of thumb is to not operate on any slope you cannot back up (in 2-wheel drive mode). You should not operate on inclines with a slope greater than a 3.5 foot rise over a 20 foot length.
Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing deck is capable of amputating hands and feet and throwing objects. The triangle in text signifies important cautions or warnings which must be followed. GENERAL OPERATION 16. Use extra care when loading or unloading the unit into a trailer or truck. 17.
Safety Rules and Information SLOPE OPERATION WARNING Slopes are a major factor related to loss-of-control and tipover accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not operate on it. Control of a walk-behind or ride-on machine sliding on a slope will not be regained by the application of the brake.
Safety Rules & Information SERVICE AND MAINTENANCE Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition. 2. Use only approved gasoline containers. 3. Never remove the gas cap or add fuel with the engine running. Allow the engine to cool before refueling. 4. Never fuel the machine indoors. 5. Never store the machine or fuel container where there is an open flame, spark, or pilot light such as near a water heater or other appliance. 6.
Identification Numbers Identification Numbers SA Product Identification Tag Model / Modéle / Model M xxxxxxxxxx PL Serial / Sèrie / Serie North American / CE Models xxxxxxxx E Briggs & Stratton Power Products Group, L.L.C. Milwaukee, WI 53201 USA Tractor ID Tag Part No. xxxxxxx SA M xxxxxxxxxxxxxxx Serial No.
Safety Decals SAFETY DECALS All DANGER, WARNING, CAUTION and instructional messages on your rider and mower should be carefully read and obeyed. Personal bodily injury can result when these instructions are not followed. The information is for your safety and it is important! The safety decals below are on your rider and mower. This unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing.
Safety Icons SAFETY ICONS Danger: Machine Rollover. Warning: Read Operator’s Manual. Do not use this machine on slopes greater than 10°. Read and understand the Operator’s Manual before using this machine. Danger: Thrown Objects. Danger: Dismemberment. This machine is capable of throwing objects and debris. Keep bystanders away. This machine can amputate limbs. Keep bystanders and children away when engine is running. Warning: Remove Key Before Servicing. Danger: Dismemberment.
Features & Controls + - Figure 1. Controls CONTROL FUNCTIONS The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see OPERATING THE TRACTOR section. Throttle Control Throttle/Choke Control (Single Lever Models) (Twin Lever Models) The throttle/choke lever controls engine speed and choke.
Features & Controls Fuel Tank Mower Height of Cut Adjustment To remove the cap, turn counterclockwise. The cutting height adjustment knob controls the mower cutting height. The cutting height is infinitely adjustable between 1” and 3-3/4.” PTO Switch The PTO (Power Take-Off) switch engages and disengages attachments that use the PTO. To engage the PTO, pull UP on the switch. Push DOWN to disengage. Note that the operator must be seated firmly in the tractor seat for the PTO to function.
Operating the Rider GENERAL OPERATING SAFETY SAFETY INTERLOCK SYSTEM Be sure to read all information in the SAFETY RULES AND INFORMATION section before attempting to operate this unit. Become familiar with all of the controls and how to stop the unit. This unit is equipped with safety interlock switches and other safety devices. These safety systems are present for your safety, do not attempt to bypass safety switches, and never tamper with safety devices. Check their operation regularly.
Operating the Rider BRAKE PEDAL OPERATION 1. See Figure 2. Depressing the pedal from position A to B disengages the transmission drive and also returns the transmission control lever to neutral (from forward speeds). Fully depressing the pedal to position B applies the rider brake. 2. See Figure 2. Parking brake is applied at pedal position B when parking brake control knob (C) is pulled up with pedal fully depressed. C + - STARTING THE ENGINE 1. Seat yourself on the rider seat in the operating position.
Operating the Rider SELECTING GROUND & ENGINE SPEED B Ground speed is selected by releasing the clutch/brake pedal (D, Figure 4) and moving the control lever (C, Figure 4) to the appropriate speed selection. If the terrain is rough, hilly or sloping, use first or second gear. If the grass is wet or over 3” (76 mm) high, use full engine speed (with slow ground speed) so the mower will have enough power to cut the grass. A D C + 1.
Operating the Rider WARNING The engine will shut off if the reverse ground speed pedal is depressed while the PTO is on and the RMO has not been activated. The operator should always turn the PTO off prior to driving across on roads, paths or any area that maybe used by other vehicles. Sudden loss of drive could create a hazard WARNING Mowing in reverse can be hazardous to bystanders. Tragic accidents can occur if the operator is not alert to the presence of children.
Operating the Rider *2396 Figure 7. Mower Removal/Installation (34” mower shown) A. Idler Pulley Arm D. Lift Cable B. Idler Pulley E. Lift Hook C. PTO (Electric Clutch) Pulley F. Rear Trailing Arms WARNING Stop engine and remove key. Do not engage PTO until mower is completely removed or installed and operator is seated. MOWER REMOVAL AND INSTALLATION NOTE: Perform mower installation on a hard, level surface such as a concrete floor.
Operating the Rider STORAGE WARNING • Battery life will be increased if it is removed, put in a cool, dry place and fully charged about once a month. If the battery is left in the unit, disconnect the negative cable. Never store the unit (with fuel) in an enclosed, poorly ventilated structure. Fuel vapors can travel to an ignition source (such as a furnace, water heater, etc.) and cause an explosion. Before starting the unit after it has been stored: • Check all fluid levels.
Regular Maintenance MAINTENANCE SCHEDULE & PROCEDURES The following schedule should be followed for normal care of your rider and mower.
Regular Maintenance C B D A E F Figure 10. Engine Compartment A. Fuel Tank B. Ignition Switch C. Battery D. Throttle / Choke Cable E. PTO Switch (Electric Clutch) F. Air Filter G. Oil Fill / Dipstick H. Fuel Filter I. Oil Drain G I H RAISING THE SEAT DECK To gain access to the engine compartment, simply tilt the seat deck forward.
Regular Maintenance LUBRICATION Lubricate the rider and mower as shown in Figures 11 16. When a grease gun is shown, wipe the fitting clean, apply two or three shots of lithium base automotive grease, and wipe off excess grease. When an oil can is shown, wipe the area clean, apply a few drops of oil (SAE 30), then wipe up drips or spills. *2388B Figure 14. Rider Lubrication Points - Rear Half (Gear Model Shown) Figure 11. Brake Pedal Pivot Point *2390 Figure 12.
Regular Maintenance BATTERY MAINTENANCE WARNING B When removing or installing battery cables, disconnect the negative cable FIRST and reconnect it LAST. If not done in this order, the positive terminal can be shorted to the frame by a tool. C Cleaning the Battery and Cables Service Interval: Every 100 Hours 1. Disconnect the cables from the battery, negative cable first (A, Figure 17). A 2. Remove the battery hold-down (C) and battery. Figure 17. Battery A. Negative Battery Terminal & Cable B.
Regular Maintenance SERVICING THE MOWER BLADES WARNING For your personal safety, do not handle the sharp mower blades with bare hands. Careless or improper handling of blades may result in serious injury. 1. Remove mower from the rider. 2. Blades should be sharp and free of nicks and dents. If not, sharpen blades as described in following steps. 3. To remove blade for sharpening, use wooden block to hold blade while removing the blade mounting capscrew (Figure 19). LOOSEN Figure 19.
Troubleshooting Adjustments & Service TROUBLESHOOTING WARNING While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. To avoid serious injury, perform maintenance on the tractor or mower only when the engine is stopped and the parking brake engaged. The troubleshooting guide below lists the most common problems, their causes and remedies.
Troubleshooting, Adjustments & Service Troubleshooting the Rider (Continued) PROBLEM CAUSE REMEDY Engine runs, but rider will not drive. 1. Ground speed control lever in neutral. 2. Transmission release lever in “push” position. 3. Belt is broken. 4. Drive belt slips. 5. Brake is not fully released. 1. Clutch is out of adjustment. 2. Pulleys or belt greasy or oily. 3. Belt stretched or worn. 4. Idler pulley pivot bracket “frozen” in declutched position. 1. Brake is incorrectly adjusted. 2.
Troubleshooting, Adjustments & Service WARNING To avoid serious injury, perform adjustments only with engine stopped, key removed and rider on level ground. A SEAT ADJUSTMENT Use the lever on the front of the seat (A, Figure 22) on to adjust the seat forward or rearward for best rider comfort. Figure 22. Seat Adjustment A. Seat Adjustment Lever *2401 Capscrews STEERING GEAR ADJUSTMENT If there is excessive slack in the steering system, the steering gear can be re-indexed to the steering shaft. 1.
Troubleshooting, Adjustments & Service BRAKE ADJUSTMENT 1-5/8” - 1-3/4” Brake Adjustment 1. Release the parking brake. 2. Brake arm (C, Figure 25) should be touching stop (B). 3. Remove cotter pin (D) and loosen the castle nut (A). Place a 0.015” feeler gauge (E) gap between the brake disc (F) and the brake puck (G). a. To decrease gap, insert feeler gauge in gap and turn nut (A) clockwise until resistance is felt on the feeler gauge. To increase gap, turn nut (A) counterclockwise and recheck gap. b.
Troubleshooting, Adjustments & Service MOWER ADJUSTMENTS WARNING If the cut is uneven, the mower may need leveling. Unequal or improper tire pressure may also cause an uneven cut. Make sure tire pressure is correct as specified in Checking Tire Pressure. To achieve proper mower levelling, perform Side-To-Side Leveling, Front-To-Back Leveling and Transport Height Adjustment procedures, in order, as follows. Before checking mower, shut off PTO and engine. Allow all moving parts to stop.
Troubleshooting, Adjustments & Service *2399 Figure 28. Leveling The Mower Side-to-Side A. Nut B. Eccentric Nut C. Rear Rollers Front-To-Back Leveling *2397 1. Make sure mower is level side-to-side and that rear rollers are on the ground. 2. Position blade(s) front-to-back. Measure the distance from the ground to front tip of blade(s), and from ground to rear tip of blade(s). On 30” mower, the front tip should be level to 1/8” (3 mm) higher than rear tip.
Troubleshooting, Adjustments & Service Transport Height Adjustment Transport height should be adjusted so that rear mower rollers are 1/8” - 1/4” (3-6 mm) above ground when mower lift lever is in transport position. To adjust, perform both mower leveling procedures first, then do the following procedure. See Figure 30. 1. Park rider on a flat level surface. 2.
Troubleshooting, Adjustments & Service *2391 To avoid damaging belts, DO NOT PRY BELTS OVER PULLEYS. RIDER DRIVE BELT REPLACEMENT Replacement of the rider drive belt requires removal of the transmission and carrier frame. Should the drive belt ever fail, contact your dealer for replacement. MOWER BELT REPLACEMENT - 30” See Figure 31. Figure 31 Belt Pattern - 30” Mower A. Idler Pulley Arm D. Front Idler Pulley B. Idler Pulley E. PTO Pulley C. Center Arbor Pulley (Electric Clutch) 1.
Specifications NOTE: Specifications are correct at time of printing and are subject to change without notice. * The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060 RPM; horsepower values are derived at 3600 RPM.
Parts & Accessories REPLACEMENT PARTS TECHNICAL MANUALS Replacement parts are available from your authorized dealer. Always use genuine Simplicity/Snapper service Parts. Additional copies of this manual are available, as well as fully illustrated parts lists. These manuals show all of the product’s components in exploded views (3D illustrations which show the relationship of parts and how they go together) as well as part numbers and quantities used.
www.simplicitymfg.com www.snapper.com Briggs & Stratton Power Products Group, L.L.C. Copyright © 2008 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved www.BRIGGSandSTRATTON.com www.MasseyLawn.
