Safety Instructions & Operator's Manual for 21” STEEL DECK WALK MOWERS SERIES 19 Models 2167519BFC (7800284) P2167519BFC (7800285) P2187519BVFC (7800286) RP2167519BDVFC (7800287) NOTE: Specifications are correct at time of printing and are subject to change without notice. * Actual sustained engine power will likely be lower due to operating limitations and environmental factors. Please refer to ‘Engine Power Rating Information’ for further details. Manual No. 7102323 (I.R.
Thank You for purchasing this quality-built Snapper product. We’re pleased that you placed your confidence in the Snapper brand. When operated and maintained according to the instructions in this manual, your Snapper product will provide many years of dependable service. This manual contains safety information to make you aware of the hazards and risks associated with the machine and how to avoid them.
Operator Safety Table of Contents Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Important Operator Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Features and Controls Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operator Safety ! Important Operator Safety Instructions WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine.
! Important Operator Safety Instructions (Continued) 6. DO NOT fill fuel containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place the containers on the ground away from the vehicle before filling. 7. Remove gas-powered equipment from the vehicle or trailer and refuel it on the ground. If this is not possible, then refuel equipment using a portable container, rather than a gasoline dispenser nozzle. 8. DO NOT start gas powered equipment in enclosed vehicles or trailers.
Features and Controls IMPORTANT The figures and illustrations in this manual are provided for reference only and may differ from your specific model. Contact your Snapper dealer if you have questions. Features and Controls G J I K H B A F D C E Features and Controls A. B. C. D. E. 4 Oil Fill Cap and Dipstick Fuel Filler Cap Recycling Cover Rear Height Adjustment Latch (2) Front Height Adjustment Latch (2) F. G. H. I. J. K.
Operation Pre-Start Check List Starting and Operation Make the following checks and perform the service required before each start-up. 1. Check the guards, deflectors, grass bag, adapter, and covers to make sure all are in place and securely tightened. 2. Check the blade control (A, Figure 1), wheel drive control (B), and ground speed control (C) to insure they work freely. Engine and Blade (Briggs Quantum and Intek Series Engines) A B 1. Move the engine speed control to the fast (‘Rabbit’) position.
Operation (Continued) Starting and Operation (Continued) Engine and Blade (Briggs DOV Series Engines) 1. Move the engine speed control past the fast (‘Rabbit’) detent to the ‘Choke’ position. 2. Pull the blade control (A, Figure 4) against the handle. 3. Pull the rope start handle (B) to crank the engine. 4. After the engine starts, allow a brief warm-up until the engine runs smooth before beginning mower operation. NOTE: To stop the engine (and blade), release the blade control. Stopping 1.
Operation (Continued) ! ! WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Cutting Height Adjustment 1. Pull the height adjusting latch (A, Figure 7) outward and move to the desired cutting height.
Operation (Continued) ! ! WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Operation Installing the Discharge Deflector 1. Remove the recycling cover. Refer to the Section entitled “Recycling Operation”. 2.
Operation (Continued) ! WARNING ! DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Installing the Grass Bag (Door Type Bag) 1. Install the grass bag adapter. Refer to the Section entitled “Installing the Grass Bag Adapter”. 2.
Maintenance Maintenance - Introduction Check Grease Level in Transmission To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention the model and serial number. ! ! WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug.
Maintenance (Continued) ! WARNING ! DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury. Check Transmission Poly-V Belt 1.
Maintenance (Continued) ! ! WARNING A B DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.
Maintenance (Continued) ! ! WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. G A B D C E F Blade Sharpening (Continued) 4. Sharpen the blade on a grinding wheel at an angle of 22 to 28 degrees (B, Figure 21). DO NOT sharpen the blade beyond the original cutting edge (A).
Maintenance (Continued) ! ! WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Drive Spring Repair/Replacement If the drive spring (A, Figure 24) is loose, reconnect. If the spring is broken, replace with a new spring.
Maintenance (Continued) ! WARNING ! A DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. B Driven Disc Adjustment (Continued) 2. Remove the driven disc spring (A, Figure 26) from the driven disc assembly (B).
Maintenance (Continued) ! WARNING ! DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Driven Disc Replacement (Continued) 2. Using needle nose pliers, unhook the drive spring (A, Figure 29) and slide the driven disc assembly off the hex shaft. 3.
Maintenance (Continued) ! ! WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Replacing the Bearing On the Pulley End Of the Hex Shaft To replace the bearing on the pulley end of the hex shaft, proceed as follows: 1.
Maintenance (Continued) ! WARNING ! DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. A B C Engine Drive Belt Replacement (Stretch Type Belts - Continued) D Maintenance IMPORTANT: Drain the fuel tank before tipping the mower.
Service Schedule ITEM SERVICE PERFORMED REF.
Troubleshooting PROBLEM PROBABLE CAUSE Engine Will Not Start Using 1. Fuel tank empty. Recoil Starter 2. Engine needs choking or priming. 3. Spark plug wire disconnected. Engine Stalls or Stops After 1. Blade control is released or is not being held Running securely against handle. 2. Fuel tank empty. 3. Engine air pre-cleaner and or air cleaner dirty. 4. Spark plug defective or gap set improperly. Engine Loses Power Excessive Vibration Troubleshooting 3. Place spark plug wire onto spark plug. 1.
2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original purchaser’s residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
Notes 22 www.snapper.
23
Notes 24 www.snapper.
Notes 25
21” STEEL DECK WALK MOWERS SERIES 19 Product Specifications Deck Size 21 in Height of Cut 1.25 - 4 in Transmission Type (Self-Propelled Models) Gear Ground Speed (Self-Propelled Models) 1 - 4 mph Engine Power - Briggs Quantum / DOV 6.75 ft-lbs (gross) Engine Power - Briggs Intek 8.75 ft-lbs (gross) Engine Displacement - Briggs DOV 160 cc Engine Displacement - Briggs Quantum / Intek 190 cc Fuel Tank Capacity - Briggs (all) 1.
