Thatcher Owner's Manual

ManualsBrandsSnapper ManualsLawn and Garden Equipment1695066

L-1782-BH-01

OWNER'S MANUAL

MODEL:

1695066

Important: This manual contains information for the safety of

persons and property. Read it carefully before assembly and

operation of the equipment!

Assembly

Installation

Operation

Repair Parts

THATCHER

Summary of content (11 pages)

PAGE 1
OWNER'S MANUAL T H AT C H E R MODE L : 1695066 Assembly Installation Operation Repair Parts Important: This manual contains information for the safety of persons and property.
PAGE 2
. L-1782-BH-01
PAGE 3
HARDWARE REFERENCE Tools Required for Assembly: * 7/16" wrench * 1/2" wrench * Flat Head Screwdriver * Hammer * Pair pliers 3.
PAGE 4
Parts Reference Parts List 4. L-1782-BH-01 REF. NO. PART NO. QTY.
PAGE 5
EXPLODED REFERENCE 19 23 32 31 17 28 27 27 26 28 28 26 27 27 22 26 12 33 25 26 26 27 25 14 29 13 26 28 20 11 29 2 1 27 16 28 20 27 5 10 8 6 11 9 4 2 15 28 27 10 4 28 30 5 7 8 30 27 6 7 3 30 30 6 5.
PAGE 6
Step 1. 25 25 2 2 2 25 Hex Lock Nut Qty. 4 1/4" x 2-1/2", Carriage Bolt Qty. 4 26 Step 2. 26 28 4 4 28 27 26 5/16" x 1", Carriage Bolt Qty. 2 6. L-1782-BH-01 27 4 Reinforcing Washer Qty. 2 27 Hex Nut Qty. 4 28 5/16" Lock Washer Qty.
PAGE 7
Step 3. 26 4 26 5/16" x 1", Carriage Bolt Qty. 8 Step 4. ! 27 Hex Nut Qty. 8 4 28 28 Reinforcing Washer Qty. 8 27 5/16" Lock Washer Qty. 8 WARNING: Failure to install safety wires can result in personal injury if a tine should disengage from tine tray. 15 7.
PAGE 8
Step 5. 27 28 26 28 27 27 Hex Nut Qty. 4 26 28 5/16" x 1", Carriage Bolt Qty. 2 5/16" Lock Washer Qty. 2 Step 6. 7 30 6 Push Nut Qty. 2 3 6 30 1/2" Flat Washer Qty. 4 8.
PAGE 9
Step 7. 10 5 5 Locking collar 8 Qty. 2 10 8 5/16", Set Screw Qty. 2 10 1/2", Nylon Bearing Qty. 4 27 Step 8. 22 26 27 Hex Nut Qty. 4 28 5/16" Lock Washer Qty. 2 28 27 20 26 5/16" x 1", Carriage Bolt Qty. 2 A 11/32" diameter hole needs to be drilled in right side of your tractor frame above front tire. Layout and drill the hole 3" from front of and center of frame lip. Step 9. 3" 9.
PAGE 10
Assembly Lift Lock bracket assembly to tractor under frame where the hole was drilled in previous step. Step 10. 26 27 28 Hex Nut Qty. 1 26 5/16" x 1", Carriage Bolt Qty. 1 5/16" Lock Washer Qty. 1 28 27 Step 11. 27 26 Hex Nut Qty. 2 5/16" x 1", Carriage Bolt Qty. 2 28 5/16" Lock Washer Qty. 2 1 29 5/16" Flat Washer Qty. 3 Hairpin Cotter Qty. 1 27 28 26 13 Lift Pin Qty. 1 13 29 1 10.
PAGE 11
Remove existing mower deck mounting pin from front of tractor. Assemble the Large or Small rod depending on whether tractor is a Simplicity or Snapper. Secure using retaining ring previously removed. Step 12. 32 31 Adjustment For most lawns, adjust the thatcher as follows: 1. Select a smooth flat surface such as a driveway, sidewalk, garage floor, etc. Attach the thatcher to the tractor according to the mounting instructions. Be sure both gauge wheels are directly under the wheel support. 2.