Use and Care Manual

ManualsBrandsSnap Safe ManualsKitchen24-Gun Fire-Resistant Digital/Mechanical Lock Gun Safe, Black

ASSEMBLING YOUR SNAPSAFE

CLOSET VAULT

1. Unpack and lay out all parts.

2. Thread DOOR HANDLE SPOKES (Part #11) onto the hub on DOOR (Part #12).

3. Install a fresh high-quality 9V battery in the Entry Keypad. (See pgs 8 and 9).

4. Important – Remove temporary door hinge bolts from door hinges.

5. Enter the factory combination code and open the DOOR, then lift it off the

DOOR FRAME (Part #6) and set aside.

6. Assemble Top, Bottom and Sides (Parts #1 through #4) rst. Then Kwik-Lock the entire

assembly onto the BACK (Part #5).

7. For additional help watch our “Live Action Assembly Video” on the “Features”

page at www.snapsafe.com.

Notes:

1. Each part is marked with an assembly number, orientation and instructions.

2. Each part’s orientation e.g. TOP, BOTTOM, FRONT, etc. matches its orientation in

the assembled vault. LEFT and RIGHT are as you face the front of the vault.

3. For easier assembly of the Kwik-Locks, remove the FIRESHIELD blankets from the TOP,

BOTTOM and SIDEWALLS. Stuff them back into place before interior assembly.

4.Screw on Kwik-Locks loosely at rst. Once all Exterior Panels are aligned and seated,

tighten the Kwik-Locks. Tightening with a tool is NOT necessary.

5.The INTERIOR SIDE PANELS are designed to t snuggly. Insert them through the

door opening bottom-to-top and then slide into nal position front-to-back.

6. Insert the INTERIOR BOTTOM PANEL through the door opening between the front

and back shelf strips and then drop into position front-to-back.

BOLTING DOWN YOUR VAULT

We recommend bolting your vault to the oor using two ¼” wedge anchor

concrete bolts through the predrilled holes in the BOTTOM of the vault.

DOUBLE SAFEGUARDING VALUABLE PAPERS

Your SnapSafe has a re protection rating of 2300ºF for one-hour. However,

we recommend that if you are going to be putting important papers in the vault, you

rst put it in a re resistant document box, and then put it in the vault.

YOUR COMBINATION CODE

• Your factory preset combination code is 1-2-3-4-5-6.

• It is recorded in a small envelope wired to the door handle of your vault.

Store this combination in a location other than your vault.

#12

Part #1 – LEFT SIDE

Part #2 – TOP

Part #3 – RIGHT SIDE

Part #4 – BOTTOM

Part #5 – BACK

Part #6 – DOOR FRAME

Part #7 – TOP INTERIOR PANEL*

Part #8 – LEFT INTERIOR PANEL*

Part #9 – RIGHT INTERIOR PANEL*

Part #10 – BOTTOM INTERIOR PANEL*

Part #11 – DOOR HANDLE SPOKES

Part #12 – DOOR

Part #15 – SHELF HARDWARE *

Part #18 – UPPER SHELF*

Part #19 – KWIK-LOCK HARDWARE*

Part #20 – GUN RACK*

Parts followed by an * are not shown

OPENING AND CLOSING

Opening:

1. Enter the 6-digit combination code.

2. Rotate 3-spoke handle clockwise into the open position and pull door open.

3. The Entry Keypad relocks in 4 seconds after a valid code has been entered.

4. The Entry Keypad will return to “standby” status with a long beep sound

if there is no operation in 10 seconds after the system has been activated.

5. If you enter an incorrect combination 4-times in a row, the lock will shut

down for 5-minutes.

Closing:

1. Close vault door.

2. Rotate 3-spoke handle counter-clockwise to the

closed position until you hear bolts engage.