Installation Instructions

2
How to Use:
E-Fitting and Snaplocs: Figure 1; When installing the E-Fitting strap end into a Snaploc
simply pull back on the leaver and insert shown end into Snaploc. Figure 2; Insert rest of
fitting fully into the Snaploc. Figure 3; Release leaver and click securely in place. Make
sure the E-Fitting strap end is as shown in Figure 3 fully secured in its place before use.
Always make sure nothing is close to or touching the E-Fitting release lever when in use
as this may cause strap to release.
1 2 3
Cam E-Strap: Figure 1; When using the Cam Buckle strap, feed strap through cam
buckle as instructed on side of cam. Figure 2; Connect both ends of strap securely to
Snaplocs. Figure 3; Pull on end of strap until strap is securely tightened. Figure 4; To
loosen strap push down on lever end of cam buckle and loosen as needed. Always make
sure nothing is close to or touching the E-Fitting release lever when in use as this may
cause strap to release. Figure 5; If your strap has a hook & loop fastener use it for
fastening excess end of strap and for storage.
1 2 3
4 5
Ring: Figure 1; When securing the Ring to a Snaploc follow the same instructions used
for the E-Fitting and Snaplocs as listed herein. Figure 2; The Ring attachment is useful for
fastening ropes, hooks and other items.
1 2
Link: Figure 1-2; The Link strap coupling connects two or more E-Straps together.
Follow the same instructions used for the E-Fitting and Snaplocs as listed herein. This
attachment is useful for extending the length of any E-Strap to fit around larger cargo
1 2
Ratchet E-Strap: Figure 1; Connect both ends of strap securely to Snaplocs. Figure 2;
Feed end of strap through ratchet receiver as shown and pull through ratchet until almost
snug on your cargo. Figure 3; Begin moving ratchet handle up and down until cargo is
secure and there is a minimum of two revolutions of strap wrapped around the center
pivot. Be sure not to over-tighten strap as this may cause damage to connection points or
cargo. Figure 4; To release, pull back on the ratchets release lever and open handle 180
degrees and pull on strap until loose. Figure 5; If your strap has a hook & loop fastener
use it for fastening excess end of strap and for storage. Depending on amount of use and
weathering, mechanisms may become restricted. A very small amount of lubrication may
be applied only on the mechanical metal parts at the location causing the restriction.
1 2 3
4 5
Hook: When installing the removable Hook on your straps, there are two options; Figure
1-2-3; For the Fixed Method slip the Hook into the E-Fitting loop at end of strap. Figure
4; For the Adjustable Method slip the hook over the strap at any location until fully in
place. The Hook can also be put on the strap in a forward or reverse position. Hooks can
be used to secure cargo with or without using the E-Fitting or Snaplocs. The bonded
protective coating on the hook is subject to scratching and rubbing off with use and is not
covered under warranty. Damaging vinyl coating will not affect the integrity of the hook.
1 2 3 4
Other great Snap-Loc products "The Snap-Loc Cargo Dolly System"...
Snap-Loc Dolly E-Strap Connection Add-On Push Add-On Panel Connector
Warranty
All Snaplocs (a.k.a. Loc-Downs), Straps and system Accessories are warranted to be
free from defects in material and workmanship for a period of 90 days (warranty period)
from date of purchase, or if you placed a special order with us from date of receipt of
product. Some items may have up to a 1 year warranty depending on store of purchase
(check with Snap-Loc or store of purchase). During the warranty period Snap-Loc will, at
its option, repair or replace without charge any part of our product found to be defective in
material or workmanship (shipping cost may be subject to charge). This warranty does not
extend to any product which has been subject to misuse, abuse, negligence, accident,
alteration, improper installation, over tightening, superseding recommended weight limits,
scratches, discoloring, or unauthorized repair. If product becomes structurally damaged
immediately discontinue use. In no way will Snap-Loc Cargo Control Systems, LLC
(Snap-Loc) be liable for special, direct, indirect or consequential damages, loss of vehicle,
cargo, profits, personal injury, death or the like for any reason. Please contact our
customer service department or the store of purchase for more details. The literature
included with this product has been written for your safety. If you do not accept the terms
and conditions herein do not use this product and return it within 7 days after purchase. By
keeping this product you are agreeing to these terms and conditions. If returning products,
return them to the store of purchase within the warranty period. No returns will be
accepted after the warranty period unless special provisions have been made with the store
of purchase (see store of purchase for further details). If you purchased your product
directly from Snap-Loc please contact the Snap-Loc Customer Service Department for a
Return Merchandise Authorization (RMA) number and return shipping instructions.
Products returned to Snap-Loc without an RMA number will not be accepted. After receipt
of an RMA number, the defective product must be returned to Snap-Loc within 30 days of
the RMA approval of it will result in loss of refund or replacement.
SNAP-LOC CARGO CONTROL SYSTEMS, LLC.
5670 La Costa Canyon Court, Las Vegas Nevada 89139 USA
800-798-4521 www.snaploc.com
(Created March 2016. Please check our website or store of purchase for any updates to this literature)