User Guide

ManualsBrandsSmittybilt ManualsAutomotiveSmittybilt 76744 SRC Carbine Front Bumper for 2007-2018 Jeep Wrangler JK

WWW.SMITTYBILT.COM

For Technical Support/Warranty Information please call 310-762-9944

Smittybilt, 400 West Artesia Blvd, Compton, CA 90220

Installation Instructions

Carbine Front Bumper

Part# 76744

07-16 JK 2 and 4 Door

Parts Included Qty

93-314TU002 Bumper 1

90-6932 Frame Hdw Pack 1

93-314TU003 Light Mount 1

12mm Lock Nut 8

90-314TU004 Fairlead Mount 1

12mm Flat Washer 8

90-314TU005 Inner Support Plate 1

90-6823 Cross Member Hdw Pack 1

90-6920 Fog Light Hdw Pack 1

10mm x 25mm Hex Bolt 4

Nylon Insert 8

10mm Flat Washer 8

#8 Phillips Screw 8

10mm Lock Nut 4

#8 Flat Washer 8

90-6089 Light Bar & Fairlead Hdw 1

90-6379 License Plate Hdw Pack 1

10mm x 35mm Hex Bolt (Fairlead) 4

6x45mm Bolt 2

10mm Flat Washer 16

6mm Flat Washer 4

10mm Lock Nut 6

6mm Lock Nut 2

10mm x 25mm Hex Bolt (Light Bar) 6

90-314TU006 License Plate Spacer 2

NOTE: Carefully review and understand instructions before installing this part.

Summary of content (7 pages)

PAGE 1
Installation Instructions Carbine Front Bumper Part# 76744 07-16 JK 2 and 4 Door WWW.SMITTYBILT.COM NOTE: Carefully review and understand instructions before installing this part.
PAGE 2
Installation Instructions Carbine Front Bumper Part# 76744 07-16 JK 2 and 4 Door WWW.SMITTYBILT.COM Step 4: Install the OE fog lights onto the bumper by first inserting the plastic retaining clips into the square cut outs on the bracket then securing the light with the included Phillip screws. (Fig C) Step 5: Install the Light/bull Bar using the included 10mm hardware. The front 2 holes mount to threaded inserts so only a 10 x 25mm bolt and flat washer is needed.
PAGE 3
Installation Instructions Carbine Front Bumper Part# 76744 07-16 JK 2 and 4 Door WWW.SMITTYBILT.COM Step 6: Install the fairlead bracket and inner support bracket (Fig E, F) with the included 10 x 35mm bolt, washer, and locknut. The inners support bracket will line up with some of the top winch mount holes. Note: using the inner support bracket increases the thickness of the winch mount plate, some winches may require longer bolts when installed.
PAGE 4
Installation Instructions Carbine Front Bumper Part# 76744 07-16 JK 2 and 4 Door WWW.SMITTYBILT.COM Drill these holes out and secure with 10x25mm Hardware.
PAGE 5
Installation Instructions Carbine Front Bumper Part# 76744 07-16 JK 2 and 4 Door WWW.SMITTYBILT.
PAGE 6
Installation Instructions Carbine Front Bumper Part# 76744 07-16 JK 2 and 4 Door WWW.SMITTYBILT.
PAGE 7
Installation Instructions Carbine Front Bumper Part# 76744 07-16 JK 2 and 4 Door WWW.SMITTYBILT.COM Limited Warranties Smittybilt’s products are covered under the following limited warranties only. Note that the duration of the limited warranty differs according to the material and finish of the product purchased.