FT982 Electric Professional Fogger CAUTION: Read and follow all instructions Do Not Return This Fogger To The Store For Help, Information or Parts, Call : 1-800-311-9903 The Fountainhead Group, Inc. 23 Garden St., New York Mills, NY 13417 1-800-311-9903 www.TheFountainheadGroup.com Manual No. 182669 Revision A.
SAFETY PRECAUTIONS • Except as provided below, use outdoors only. Fire or explosion may occur if used in confined area. • Barrel is hot when plugged in. Allow to cool before touching . • Never secure trigger in a permanent “ON” position. Overheating may occur. • Release trigger immediately if a flame occurs in the barrel. • Do not fog near combustible materials. • Fog produced is flammable. Do not fog near open flames such as gas burner or pilot light. • Fog produced may be toxic.
OPERATION INSTRUCTIONS Assembling NOTE: Before each use, be sure nozzle cap on fogger is tightened securely. 1. With fogger unplugged, Inspect nozzle cap by pulling barrel away from fogger body as shown. (See Figure 1) Figure 1 2. Inspect nozzle for any accumulation of any foreign matter. Clean nozzle if needed before using and secure nozzle tightly. (See Figure 2) NOZZLE CAP Figure 2 3. Attach barrel by positioning the prongs directly in line with the slots provided for them in the housing.
OPERATING INSTRUCTIONS CONTINUED Fogging - For Use Outdoors Only “except as provided in #6 below” 1. Allow the fogger to pre-heat for two minutes or more. 2. Carry the fogger as you would a suitcase, holding it about three feet off the ground and away from your side. 3. Pull the trigger, conveniently located on the underside of the handle, to start the unit operating. Release trigger to stop, 4. Turn adjustment knob clockwise to obtain a dry fog.
REPLACEMENT PARTS 1 2 3 4 5A 5B 5A KIT #5 5C 5D 6 7 KEY NO. MODEL NO. 1 982 2 3 4 ALL MODELS ALL MODELS 982 PART NO. 161222 161214 161900 161189 161160 DESCRIPTION BARREL ASSEMBLY, COMPLETE, 115V BARREL ASSEMBLY, COMPLETE, 230V BRASS NOZZLE SPINNER AND SPRING ASSEMBLY CONTAINER GASKET KIT #5 1602011C PUMP PARTS KIT (ALL MODELS) KEY NO. 5A 5B 5C MODEL NO. ALL MODELS ALL MODELS ALL MODELS 5D ALL MODELS KEY NO. MODEL NO. 6 ALL MODELS 7 982 8 ALL MODELS PART NO.
TROUBLE-SHOOTING GUIDE Symptom Probable Cause Corrective Action Poor fog quality 1. Low Voltage. 1. Change to another power source. 2. Too light a gauge extension cord. 2. See page 2, Item #5. 3. Poor grade fogging material. Dripping 1. Nozzle loose. 1. Tighten securely. 2. Excessive chemical output. 2. Adjust to drier output. 3. Worn out Barrel Assembly. 3. Replace with factory replacement assembly only. 4. Other-see poor fog quality. No fog- No spray (Unit vibrates) No fog-Spray Ok 1.
Limited Warranty We warrant that each product sold by us will be free from defects in material and workmanship for a period of 90 days from the date of shipment by us, We make no other express warranties, and all implied warranties, including fitness and merchantability, are limited to 90 days from date of shipment by us. Within the warranty period, we will repair or replace any part found to be defective upon our examination but will not pay shipping costs or other expenses.
SERVICE KITS, PARTS & ACCESSORIES ARE AVAILABLE BY CONTACTING The Fountainhead Group, Inc. - Customer Service Center Monday - Friday 8 a.m. - 5 p.m., EST Toll Free: 1-800-311-9903 or e-mail: Info@TheFGI.com or Access online at: www.TheFountainheadGroup.
