Contents 1. INSTRUCTIONS FOR SAFE AND PROPER USE _______________________________4 2. INSTALLATION OF THE APPLIANCE_________________________________________6 3. ADAPTATION TO DIFFERENT TYPES OF GAS ________________________________9 4. FINAL OPERATIONS_____________________________________________________12 5. DESCRIPTION OF CONTROLS ____________________________________________14 6. USE OF THE HOB _______________________________________________________16 7.
Introduction 1. INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKER. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKER. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE.
Introduction DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE HOB GRIDS. DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO TOUCH THE HEATING ELEMENTS INSIDE THE OVEN. DO NOT USE CONTAINERS OR BROILERS THAT EXTEND BEYOND THE OUTER PERIMETER OF THE HOB. THE APPLIANCE IS DESIGNED FOR USE BY ADULTS. DO NOT ALLOW CHILDREN TO GO NEAR OR PLAY WITH IT. WHEN OPERATING THE GRILL ALL ACCESSIBLE PARTS COULD BECOME VERY HOT: KEEP OUT OF THE WAY OF CHILDREN.
Instructions for the installer 2. INSTALLATION OF THE APPLIANCE It is the law that all gas appliances are installed by competent persons. Corgi gas installers are approved to work to safe and satisfactory standards. All gas installation, servicing and repair work must be in accordance with the gas safety regulations 1984 (installation and use) as amended 1990.
Instructions for the installer 2.1 Electrical connection Make sure that the power line voltage matches the specifications indicated on the rating plate located inside the storage compartment. This rating plate must never be removed. If the appliance is connected to the supply by means of a fixed connection, install a multipolar cut-out device on the line, with contact opening distance equal to or greater than 3 mm, located near the appliance and in an easily reachable position.
Instructions for the installer 2.3 Connecting to natural and LPG gas (Please see connection diagram) Make the connection to the appliance using flexible bayonet style hose in accordance to B.S. 669. The hose connection at the rear of the appliance has a ½” BSP internal thread. Please use seal C between the flexible connection L and the appliance supply tube B. When making the connection, make sure that no stress of any kind is applied to the cooker and that the hose does not touch any sharp edges.
Instructions for the installer 3. ADAPTATION TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, disconnect the appliance from the mains. The cooker hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. In the case of operation with other types of gas the burner nozzles must be changed and the minimum flame adjusted on the gas taps. To change the nozzles, proceed as described below. 3.
Instructions for the installer 3.2 Burner and nozzle characteristics table (Mod. 90 cm.) Rated heating capacity (kW) Burner Auxiliary Semi rapid Rapid Triple crown Oven Maxi oven Grill 1.0 1.75 3.0 3.2 3.2 5.2 4.0 Rated heating capacity (kW) Burner Auxiliary Semi rapid Rapid Triple crown Oven Maxi oven 1.0 1.75 3.0 3.5 3.2 5.
Instructions for the installer 3.4 Burner and nozzle characteristics table (Mod. 60 cm.) Portata termica nominale (kW) Bruciatore LPG – G30/G31 28/37 mbar Diametro Ugello 1/100 mm By-pass mm 1/100 Portata ridotta (W) Portata g/h G30 Portata g/h G31 Auxiliary 1.0 50 30 350 73 71 S Semi rapid 1.75 65 33 450 127 125 Rapid 3.0 85 45 800 218 214 Triple crown 3.2 91 65 1500 233 229 Oven 3.2 87 48 850 233 229 Grill 3.
Instructions for the installer 4. FINAL OPERATIONS After replacing the nozzles, reposition the flame-spreader crowns, the burner caps and the grids. Following adjustment to a gas other than the preset one, replace the gas adjustment label fixed to the appliance with the one corresponding to the new gas. This label is in the packet together with the nozzles. 4.1 Regulation of the hob burner minimum level for natural gas Light the burner and turn it to the minimum position .
Instructions for the installer 4.4 Wall fixing • • • • Stretch out the chain attached to the cooker horizontally so that the other end touches the wall. Mark the wall in the position where the hole is to be drilled. Drill the hole, insert a wall plug and attach the chain. Move the cooker up against the wall.
Instructions for the installer 5. DESCRIPTION OF CONTROLS 5.1 Front control panel All the cooker controls and commands are on the front panel. If the cooker is equipped with an electronic programmer, before using the oven make sure that the symbol ; appears on the display. See paragraph “8. ELECTRONIC PROGRAMMER”.
Instructions for the user VARIABLE GRILL KNOB This allows to vary heat intensity when cooking with the grill. The knob can be set with continuity between “0” and the stop release position, which corresponds to maximum heat. ELECTRIC OVEN CONTROL KNOB Each of the functions listed below can be used (except the oven light and the small grill) only together with the correct temperature thermostat regulation as described on page 14 of this manual.
Instructions for the installer 6. USE OF THE HOB 6.1 Lighting of the hob burners Before lighting the hob burners check that the flame caps are in the correct position and that their burner caps are in place, making sure that the holes A in the flame caps correspond to the spark plugs and thermocouples. The optional grid B is for use with “woks” (Chinese pans). To prevent deterioration of the hob we have equipped the cooker with a raised pan stand C to be placed underneath pans more than 26 cm in diameter.
Instructions for the user 6.3 Diameter of the vessels to be used on each burner BURNERS 1 2 3 4 Auxiliary Semi rapid Rapid Triple crown Ø min. and max.
Instructions for the installer 7. USE OF THE OVEN For the models with electronic programmer, before using the oven make sure that the display shows the symbol . 7.1 Warnings and general advice Using the oven and the grill for the first time, heat them to the maximum temperature (260°C) for as long as it takes to burn off any production oil residues which could give a nasty flavour to the food. . To adjust refer to After a power cut, the oven display will flash intermittently and show paragraph "8.
Instructions for the user 7.2.2 Using the rotisserie in cookers with maxi oven Fit the supporting frame onto the second runner up from the bottom so that the seat to take the rod projects outside the oven. Place the rod as shown in the diagram (1) and push the frame into the oven until the end of the rod reaches the hole in the rotisserie motor. Now push the rotisserie rod to the left until it reaches the position shown in the diagram (2). To activate / ).
Instructions for the installer 7.3 Using the pIzza function (only on some models) This appliance Is equipped with a function specially developed for cooking pizza. This function is symbol on the oven functions knob. identified by the To cook a pizza, proceed as described below. With the oven cold, remove the round cover from the bottom of the oven (fig. 1) and fit the pizza plate in its place (Fig. 2).
Instructions for the user 8. ELECTRONIC PROGRAMMER (ONLY ON EQUIPPED MODELS) LIST OF FUNCTIONS MINUTE-COUNTER KEY COOKING TIME KEY END-OF-COOKING KEY DECREASE TIME KEY INCREASE TIME KEY 8.1 Clock adjustment When using the oven for the first time, or after a power failure, the display flashes regularly and indicates . Press the keys and at the same time the keys or : each single press changes the time by 1 minute either up or down.
Instructions for the installer 8.4 End of cooking When cooking is over, the oven will automatically switch off and, at the same time, an intermittent alarm will sound. After switching off the alarm, the display will once again show the right time together with the symbol , indicating that the oven has returned to manual operation mode. 8.5 Minute Counter The programmer can also be used as a simple minute counter.
Instructions for the user 9. AVAILABLE ACCESSORIES The oven has 4 support for positioning plates and racks at various heights. Oven grill: for cooking food on plates, small cakes, roasts or food requiring light grilling. Plate grill: for placing above plate for cooking foods that might drip. Oven plate: useful for catching fat from foods on the grill above. Pizza plate: specially designed for cooking pizza. For use as described in point “8.
Instructions for the installer 10. CLEANING AND MAINTENANCE 10.1 Cleaning stainless steel and enamelled versions To maintain stainless steel in good condition clean it regularly after each use, once it has cooled down. 10.1.1 Ordinary daily cleaning To clean and preserve the stainless steel surfaces, always use only specific products that do not contain abrasives or chlorine-based acids.
Instructions for the user 10.3 Cleaning of oven For best oven upkeep clean regularly after having allowed to cool. Take out all removable parts. • • Clean the oven grill with hot water and non-abrasive detergent. Rinse and dry. Do not allow residues of sugary foods (such as jam) to set inside the oven. If left to set for too long, they might damage the enamel lining of the oven. 10.4 Door glass The door glass should always be kept clean. Use absorbent kitchen paper to clean.
Instructions for the installer 11. EXTRAORDINARY MAINTENANCE The oven may require extraordinary maintenance or replacement of parts subject to wear such as seals, bulbs, and so on. The following instructions describe how to carry out these minor maintenance operations. Before any intervention, disconnect the power supply of the device. 11.1 Replacement of light bulb Remove cover A by twisting anticlockwise, replace bulb B with another similar bulb (25 W). Refit the cover A. Only use oven bulbs (T 300°C).
