Washing machine LBS 845
Contents Specifications of your Washing Machine >4 Warnings >5 Installation >6 Preparation >8 Program Selection and Operating Your Machine >9 Maintenance and Cleaning 122 > 13
Your Washing Machine Detergent Drawer Adjustable feet Control panel Front door Tabletop Filter cover 323
Specifications of your Washing Machine Maximum dry laundry capacity (kg.) 4.5 Height (cm.) 85 Width (cm.) 60 Depth (cm.) 45 Net Weight (kg.) 58 Electricity (V/Hz.) 230/50 Total Current (A) 10 Total Power (W) 2350 Washing -rinsing cycle (cyc/min) 52 Spinning cycle (max cyc/min) 800 In order to improve the product quality, modifications can be made in the specifications without prior notice.
Warnings • • • • • • • • • • • This product is designed for home use. Your washing machine is adjusted to 230V. If the fuse in your house is less than 16A than have a certified electrician deploy an 16A fuse. In case of transformer or non-transformer use, grounding installation must be performed with a licensed electrician. Any use before grounding is not our responsibility. Never place your machine over a carpet covered floor. Otherwise electrical parts of your machine may overheat.
Installation 1. Removing the packaging reinforcements To remove the packaging reinforcement lean the machine backward, take the reinforcement by pulling from the braid. 2. Removing the transportation safety bolts Before operating the machine, the transportation safety bolts must definitely be removed. For this, 1. Loosen the “C” bolts thoroughly by turning them anticlockwise with the help of a suitable wrench. 2. Pull off the transportation safety bolts. 3.
Water connections Models with double water inlets can be used as a model with a single water inlet by using a plug. Plug should be installed to the hot water valve. A rubber gasket should be used in order to prevent water leakage from the connection point. a) Water inlet hose The specific hoses that come with the machine are connected to the water inlet valves on the machine. Red labeled hose is for hot water inlet and blue labeled hose is for cold water inlet.
Electrical Connection Plug in the grounded plug at the end of the power cable of the washing machine to a grounded wall outlet which is fed with suitable voltage and current. Preparation • Please note the followings before start ing to wash your laundry: - Have you plugged the machine? - Have you connected the drainage hose as necessary? - Have you closed the front door? - Have you opened the tap? • If you are installing your machine by yourself, please read the “Installation” section first.
Put the powder detergent and softener into the appropriate compartments in the detergent drawer and close the detergent drawer. Pour the softener as recommended in the package (generally <100ml; i.e. 1 tea cup) Never exceed the “MAX” marking. If you put more, it will mix into the washing water via siphon (III) and it will be wasted. In this case, it may be necessary to refill the softener. If the softener is condensed over time, it may be necessary to dilute with some water.
Pressing the “On/Off” button never means that the program is started. You must press “Start/Pause/Cancel” button in order the machine starts its program. Program selection table Cotton 90 Very dirty, heat resistant cotton, linen 4.5 150 50 1.60 Cotton 60* Normal dirty, heat resistant cotton, linen 4.5 135 49 0.85 Cotton 40 Less dirty or heat resistant cotton 4.5 125 45 0.60 Intensive 60 Very dirty, heat resistant cotton, linen 4.5 160 50 1.
Function Selection Additional functions selectable according to selected program can be selected by pressing related key. Led of selected function will be on. If not selected together some additional functions go off when it is not selected with other one. For example; when using cotton program, quick wash and rinse plus auxillary functions can not be selected together. After selecting quick wash program, if rinse plus key is pressed fast program will be on and quick wash function led will go off.
Cotton40 can be used. For selecting Cotton40 instead of Cotton60 by pressing “Start/Pause/Cancel” key machine is switched to pause position. Program knob is turned for selecting Cotton40 program. Even when the program selection knob is changed during the program initially selected program will be executed. For changing washing program continuing program must be cancelled. Although selected auxillary functions must be compatible with washing program.
Maintenance and cleaning Detergent Drawer The powder detergent remnants may accumulate in the detergent drawer. To clean the detergent drawer, pull the drawer towards you by pressing the marked point of the siphon in the softener compartment as shown in the illustration. Wash the drawer in the sink with plenty of water. Siphon Do not forget to clean the siphon (the colored part in the detergent drawer) when it gets dirty. To remove the siphon, first take out the detergent drawer.
Hose Since there is a risk of freezing especially in the cold areas, the water remaining in the appliance can frozen and damage the appliance. In this case, the water remaining in the pump and hoses should be drained by removing the pump filter. Water inlet hoses should also be emptied by removing them from the taps. Cleaning the pump filter • Clean the foreign substance filter periodically at least for once! • If the foreign substances (coins, buttons, baby socks and etc.
