Datasheet
1
2
Stations
3
U side
D side
—
D
D0
D3
D16
Direct mounting
DIN rail mounting (With DIN rail)
DIN rail mounting (Without DIN rail)
For 3 stations
For 16 stations
Specify a longer rail
than the standard
length.
···
···
—
S
R
Internal pilot
Internal pilot, Built-in silencer
External pilot
∗ For built-in silencer type, P and E ports are
available on U and D sides. 3/5(E) port is
plugged. The silencer exhaust port is located
on the opposite side of P, E port entry.
(Example: When the P, E port entry is D side,
the silencer exhaust port is U side.)
Note) t For type “S”, supply/exhaust block
assembly with built-in silencer, choose U
or D for P port entry.
U
Note)
D
Note)
B
U side (2 to 10 stations)
D side (2 to 10 stations)
Both sides (2 to 16 stations)
02
08
02
16
2 stations
8 stations
2 stations
16 stations
Double wiring
Note 1)
Specified layout
Note 2)
(Available up to 16 solenoids)
Symbol Stations
Note
SS5Y 12S33 UR1 05
3
5
7
SY3000
SY5000
SY7000
Example (SS5Y3-12S3V-l)
q w re t y u
q
Series
e Valve stations r P, E port entry
u Mounting
t SUP/EXH block assembly
w SI unit
RoHS
Symbol
—
N
SY3000
ø8
ø5/16"
SY5000
ø10
ø3/8"
SY7000
ø12
ø1/2"
y P, E port size (One-touch fittings)
Connector Connecting Base
Series SY3000/5000/7000
How to Order Manifold
Plug-in
EX120
Refer to pages 186 to 188
for dimensions of Type
12/Top ported type.
Under the manifold part number, state the valves to be mounted in order
from the 1st station as shown in the figure above. If the arrangement
becomes complicated, specify on a manifold specification sheet.
∗ For N, sizes are in inches.
Note 1) When mounted on the DIN rail without
the SI unit, please select D0 and refer
to L3 of the dimensions for the DIN rail
length, then order separately. (Refer to
page 225 for the DIN rail part number.)
Note 2) Refer to page 247 for the fixation of
DIN rail mounting type manifold.
Type 12
Top Ported
Note 1) Double wiring: 2-position single, double,
3-position and 4-position valves can be
used on all manifold stations.
Use of a 2-position single solenoid will
result in an unused control signal. If this is
not desired, order with a specified layout.
Note 2) Specified layout: Indicate the wiring
specifications on the manifold
specification sheet. (Note that 2-position
double, 3-position and 4-position valves
cannot be used where single wiring has
been specified.)
Note 3) This also includes the number of blanking
plate assembly.
Note 4) Since R2 type SI unit has 8 outputs, note
that up to 8 solenoids can be
accommodated.
2-position double (24 VDC)
SY3230-5U1-C6 (1 set)
2-position single (24 VDC)
SY3130-5U1-C6 (3 sets)
3-position closed
centre (24 VDC)
SY3330-5U1-C6 (1 set)
Manifold base
(5 stations)
SS5Y3-12S3V-05D
SS5Y3-12S3V-05D ··· 1 set
(Type 12 5-station manifold base part no.)
∗SY3130-5U1-C6 ······· 3 sets (2-position single part no.)
∗SY3230-5U1-C6 ······· 1 set (2-position double part no.)
∗SY3330-5U1-C6 ······· 1 set (3-position closed centre part no.)
The asterisk denotes the symbol for assembly.
Prefix it to the part numbers of the valve etc.
Note 1) Ensure a match with the common
specification of the valve to be used.
Note 2) The communication connector (for the
opposite side) is not provided. Please
order it separately.
0
Q
R1
R2
V
ZB
Note 2)
ZBN
Note 2)
Without SI unit
DeviceNet™ (Positive common NPN)
OMRON CompoBus/S
(Positive common NPN)
CC-Link (Positive common NPN)
CompoNet™
Positive common NPN
Negative common PNP
16 outputs
8 outputs
···
···
···
···
How to Order Manifold Assembly
For details about the EX120 Integrated-type (For Output)
Serial Transmission System, refer to the WEB catalogue or
the Best Pneumatics No. 1 and the Operation Manual. For
details about part numbers of SI units to be mounted, refer to
page 218 in this catalogue. Please download the Operation
Manual via SMC website, http://www.smcworld.com
179