Datasheet
2 through 8 station manifold.
How to Order Manifolds
How to Order Manifold Mounted
IITV20 02 5
Manifold Specifications (Except Series ITV3000)
8
How to Order Manifold Assemblies
Example
Pressure response with no load is approx. 0.1 sec.
High-Speed Response Time Type
7
ITV X882 0 1 0 S0 1 2
Pressure display unit
—
2
3
4
5
MPa
kgf/cm
2
bar
psi
kPa
∗
∗
Model
1
2
1000 type
2000 type
Pressure range
1
3
5
0.1 MPa
0.5 MPa
0.9 MPa
Power supply
voltage
0
1
24 VDC
12 to 15 VDC
Input signal
0
1
2
3
Current type 4 to 20 mA DC (Sink type)
Current type 0 to 20 mA DC (Sink type)
Voltage type 0 to 5 VDC
Voltage type 0 to 10 VDC
1
2
3
4
Analogue output 1 to 5 VDC
Switch output/NPN output
Switch output/PNP output
Analogue output 4 to 20 mA DC (sink type)
Monitor output
Thread type
—
N
T
F
Rc
NPT
NPTF
G
Port size
1
2
3
1/8 (1000 type)
1/4 (1000, 2000 type)
3/8 (2000 type)
Bracket
—
B
C
Without bracket
Flat bracket
L-bracket
Cable connector type
S
L
N
Straight type 3 m
Right angle type 3 m
Without cable connector
ITV1000, 2000
02
03
OUT port size
Connection thread type
1/4
3/8
—
N
F
PT
NPT
PF
2
8
Stations
2 stations
8 stations
Note) Refer to the table below for possible mixed combination.
Model
ITV101
ITV103
ITV105
ITV201
ITV203
ITV205
ITV101
ITV103
ITV105
ITV201
ITV203
ITV205
IITV20-02-3 ……………………
∗ITV1030-311S-X26 …………
∗P398020-13 …………………
∗ITV2050-212S-X26 …………
1 set (3 station manifold base part no.)
1 set (Electro-pneumatic regulator part no.)
Note 2)
1 set (Blanking plate assembly part no.)
1 set (Electro-pneumatic regulator part no.)
Note 2)
The ∗ is the symbol for mounting. Add the ∗ symbol at the beginning of part
numbers for electro-pneumatic regulators, etc. to be mounted on the base.
Note
1)
Electro-pneumatic regulators are counted starting from station 1 on
the left side with the OUT ports in front.
Note
2)
The port size for mounted electro-pneumatic regulators is Rc 1/8
(ITV1000), Rc 1/4 (ITV2000) only.
Note 3) When there is a large number of stations, use piping with the largest
possible inside diameter for the supply side, such as steel piping.
Note
4)
The use of the straight type cable connector is recommended. To
mount right angle type, be certain to check that no possible
interference occurs.
Note
5)
When mounting a blanking plate and the regulator with different
pressure set, please inform SMC of the order of a manifold station
beside a purchase order.
∗ Under Japan's new Measurement Act,
this is only for overseas sales
(SI units are to be used inside Japan).
1
2
3
Note 1)
Stations
IITV20-02-3
Manifold base (3 stations)
P398020-13
Blanking plate assembly
ITV1030-311S-X26
Electro-pneumatic regulator
ITV2050-212S-X26
Electro-pneumatic regulator
ITV 0 X261 1
ITV 0 X262 2
Note 1) ! in part number is the same model no. for the standard products.
Note 2) For communication models, consult SMC for availability.
Note 3) The thread type is Rc only.
Note 4) For Series ITV1000, the port size is 1/8 only.
Note 5) For Series ITV2000, the port size is 1/4 only.
Note 6) The bracket accessory can not be selected.
Note 7) Not applicable to Series ITV3000
®
RoHS
Made to
Order
Made to Order Specifications 3
Series ITV1000/2000/3000
Please contact SMC for detailed dimensions, specifications and lead times.
27