Brochure

ManualsBrandsSMC ManualsAutomationPressure Control Valve 5 ... 900kPa, 1500L/min

How to Order

ITV

Pressure range

1 0

0.1 MPa

0.5 MPa

0.9 MPa

S Q

0 1 2

—

MPa

kgf/cm

bar

psi

kPa

Input signal

Cable connector type

Straight type 3 m

Right angle type 3

Without cable connector

Bracket

—

Without bracket

Flat bracket

L-bracket

Monitor output

—

Thread type

—

NPT

NPTF

Port size

1/8 (1000 type)

1/4 (1000, 2000, 3000 type)

3/8 (2000, 3000 type)

1/2 (3000 type)

Power supply voltage

24 VDC

12 to 15 VDC

Model

1000 type

2000 type

3000

type

Note)

Current type 4 to 20 mA (Sink type)

Current type 0 to 20 mA (Sink type)

Voltage type 0 to 5 VDC

Voltage type 0 to 10 VDC

Preset input

CC-Link

DeviceNet™

PROFIBUS DP

RS-232C communication

None (for communication models)

None (for preset input)

Analogue output 1 to 5V DC

Switch output/NPN output

Switch output/PNP output

Analog output 4 to 20 mA (Sink type)

Note) Communication

models are availa-

ble only for 24 V

Pressure display unit

Made to Order Specifications

See pages 11, 25, and 26 for details.

CE compliant

∗

For detailed information on

CE marked models, refer to

SMC's website.

Note) Only for overseas sales (SI units are

to be used inside Japan). No units are

displayed on communication models.

Note) Communication cable (other than RS-

232C) should be obtained separately.

See below.

Application

CC-Link compatibility

DeviceNet™

compatibility

PROFIBUS DP

compatibility

Communication cable part number

PCA-1567720 (Socket type)

PCA-1567717 (Plug type)

PCA-1557633 (Socket type)

PCA-1557646 (Plug type)

PCA-1557688 (Socket type)

PCA-1557691 (Plug type)

Remarks

Dedicated Bus adapter supplied

with the product.

T-branch connector not supplied.

For communication cables, use the parts listed below

(refer to the catalogue [M8/M12 Connector] CAT.EUS100-73-UK for details)

or order the product certified for the respective protocol (with M12 connector) separately.

Electro-Pneumatic Regulator

Series

ITV1000/2000/3000

Model

Maximum supply pressure

Minimum supply pressure

24 VDC ± 10%, 12 to 15 VDC

Set pressure +0.1 MPa

Set pressure range

Note 1)

0.2 MPa

Input signal

Input

impedance

Output pressure

display

Note 4)

Weight

Note 9)

Accuracy

Minimum unit

ITV10

ITV20



ITV30



Ambient and fluid temperature

Enclosure

1.0 MPa

0.005 to 0.1 MPa 0.005 to 0.5 MPa 0.005 to 0.9 MPa

JIS Symbol

4 to 20 mA, 0 to 20 mA (Sink type)

0 to 5 VDC, 0 to 10 VDC

4 points

250

Ω or less

Note 6)

Approx. 6.5 kΩ

Approx. 2.7

kΩ

Linearity

Hysteresis

Repeatability

Sensitivity

Temperature characteristics

Power supply

Voltage

Current

consumption

Within ±1% (Full span)

Within 0.5% (Full span)

Within

±0.5% (Full span)

Within 0.2% (Full span)

Within ±0.12% (Full span)/°C

±3% (Full span)

MPa: 0.01, kgf/cm

: 0.01, bar: 0.01, PSI: 0.1

Note 5)

, kPa: 1

0 to 50

°C (No condensation)

IP65

Approx. 250 g (without options)

Approx. 350 g (without options)

Approx. 645 g (without options)

NPN open collector output: Max. 30 V, 30 mA

PNP open collector output: Max. 30 mA

Power supply voltage 24 VDC type: 0.12 A or less

Power supply voltage 12 to 15 VDC type: 0.18 A or less

ITV105

ITV205



ITV305



ITV103



ITV203



ITV303



ITV101



ITV201



ITV301



1 to 5 VDC (Load impedance: 1 kΩ or more)

4 to 20 mA (Sink type) (Load impedance: 250

Ω or less)

Output accuracy within

±6% (Full span)

Input/output characteristics chart

Input signal (%F.S.)

0 100

Output pressure

(MPa)

This range is outside

of the control (output).

0.005MPa

Rated pressure

ITV3000 Fieldbus-compatible

model

ITV2000ITV1000

Note 1) Please refer to Figure 1 for the relationship between set pressure and input. Because the maximum set pres-

sure differs for each pressure display, refer to Appendix 7.

Additionally, refer to page 18 for the set pressure range by units of standard measured pressure.

Additionally, refer to page 18 as maximum set pressure differs on unit of standard measure.

Note 2) 2-wire type 4 to 20 mA is not available. Power supply voltage (24 VDC or 12 to 15 VDC) is required.

Note 3) Select either analogue output or switch output.

Further, when switch output is selected, select either NPN output or PNP output.

Note

Adjustment of numerical values such as the zero/span adjustment or preset input type is set based on the mi-

nimum units for output pressure display (e.g. 0.01 to 0.50 MPa). Note that the unit cannot be changed.

Note 5) The minimum unit for 0.9 MPa (130 psi) types is 1 psi.

Note 6)

Value for the state with no over current circuit included. If an allowance is provided for an over current circuit,

the input impedance varies depending on the input current. This

is 350 Ω or less for an input current of 20

mA DC.

Note 7) The above characteristics are confined to the static state. When air is consumed on the output side, the pres-

sure may fluctuate.

Note 8) For communication models, the maximum current consumption is 0.16 A or less.

Note 9) For communication models, add roughly 80 g to the weight (100 g for the PROFIBUS DP).

Note 10) The ITV1000 series is a non-grease model (Wetted parts).

Standard Specifications

Note 10) Note 10) Note 10)

Current type

Note 2)

Voltage type

Preset input

Current type

Voltage type

Preset input

Switch

output

Analogue

output

Output signal

(monitor

output)

Note 3)

Protocol

Version

Note 1)

Configulation file

Note 2)

I/O occupation area

(input/output data)

Communication data resolution

Fail safe

Note 4)

Terminating

resistance

Communication

speed

Communication Specifications

Model

ITV00-CC

CC-Link

Ver 1.10

—

12 bit (4096 resolution)

ITV00-DN

DeviceNet™

Release2.0

EDS

16 bit/16 bit

12 bit (4096 resolution)

—

ITV00-PR

PROFIBUS DP

DP-V0

GSD

16 bit/16 bit

12 bit (4096 resolution)

CLEAR

ITV00-RC

RS-232C

—

9.6 kbps

—

10 bit (1024 resolution)

HOLD

—

Note 1) Note that this version information is subject to change.

Note 2) Configulation files can be downloaded from SMC's website: http://www.smc.eu

Note 3) The output HOLD value when a CC-Link communications error occurs can be set based on the bit area data.

Note 4) It shows the insulation between electric signal for communication and the ITV supply power.

156 k/625 k

2.5 M/5 M/10 M bps

125 k/250 k/500 k bps

9.6 k/19.2 k/45.45

93.75 k/187.5 k/500

1.5 M/3 M/6 M/12 M bps

Built into the product

(Switch setting)

HOLD/CLEAR

(Switch setting)

4 word/4 word, 32 bit/32 bit

(per station, remote device station)

HOLD

Note 3)

/CLEAR

(Switch setting)

Electro-Pneumatic Regulator

Series ITV1000/2000/3000