Brochure

Panel mount
adapter
Front protective cover
Panel
Enlarged view
Panel mount
adapter
M5 female thread type R1/8, NPT1/8 type
1. Do not use pressure sensors with corrosive and/or
flammable gases.
7. The applicable fluids are air, non-corrosive gas,
non-flammable gas. Consult with
SMC if the switch
is to be used with other types of fluids.
Warning
1. Do not drop, bump, or apply excessive impacts (100
m/s
2
) while handling. Although the body of the sen-
sor may not be damaged, the internal parts of the
sensor could be damaged and lead to a malfunction.
2. The tensile strength of the cord is 35 N. Applying a
greater pulling force on it can cause a malfunction.
When handling, hold the body of the sensor––do
not dangle it from the cord.
3. Avoid repeatedly bending or stretching lead wires.
If the lead wires are routed in such a way that repe-
titive bending stress or tensile strength is applied,
it may cause them to break. When the lead wire is
moving, secure it near the switch of the unit. The
minimum bending radius is approximately R40 to
60 mm or more. Consult with SMC for details.
4. Do not exceed the screw-in torque of 1 N·m or less
for the M5 female thread type after tightening ap-
proximately 1/6 of a turn, and 7 to 9 N·m for R1/8
and NPT1/8 type. Exceeding this value can damage
the product. Also, the wrench should be applied to
the metal part integrated with piping (connected at-
tachment). Applying the wrench to other parts may
lead to damage to the product.
5. Allow a sufficient margin of tube length in piping in
order to prevent application of torsional, tensile or
moment load to the tubes and fittings.
6. When a brand of tubing other than SMC is used,
make sure that the tolerance of the tube’s O.D. sa-
tisfies the following specifications.
1) Nylon tubing: within ±0.1 mm
2) Soft nylon tubing: within ±0.1 mm
3) Polyurethane tubing: within +0.15 mm, within –0.2 mm
Caution
Handling
1. SMC pressure switches do not have an explosion
proof rating. Never use in the presence of an explo-
sive gas as this may cause a serious explosion.
Operating Environment
Warning
1. SMC pressure switches are CE marked; however,
they are not equipped with surge protection against
lightning. Lightning surge countermeasures should
be applied directly to system components as ne-
cessary.
2. Do not use in an environment where static electri-
city can cause problems, otherwise system failure
or malfunction may result.
Caution
1. Mounting with panel mount adapter
Caution
Mounting
Series ZSE10
(
F
)
/ISE10
Specific Product Precautions 1
Be sure to read before handling.
Refer to back pages 1 and 2 for Safety Instructions and Handling Precautions for SMC
Products (M-E03-3) for Precautions.
1. Incorrect wiring can damage the switch and cause a
malfunction or erroneous switch output. Connec-
tions should be done while the power is turned off.
2. Do not attempt to insert or pull the connector when
the power is on.
A switch output malfunction may
occur.
3. Wire separately from power lines and high voltage
lines, avoiding wiring in the same conduit with the-
se lines. Malfunctions may occur due to noise from
these other lines.
4.
If a commercial switching power source is used,
make sure that the F.G. terminal is grounded.
Connection
Caution
Tube
One-touch fitting
Direct mountingClose mounting
Claw 1
Claw 2
Claw 1
Claw 2
q
w
e
Claw 1
Claw 2
q
w
A part (Lever)
• To connect the connector, insert it straight while pinching the
lever, and then push the lever into the jack of the housing and
lock it.
• To remove the connector, pull it straight out while applying
pressure with your thumb to the
A part (lever) and unhooking
it from the jack.
• Do not attempt to insert or pull the connector when the power
is on. A switch output malfunction may occur.
Connection/Removal of Connector
• Cut the tube perpendi-
cularly.
• Hold the tube and in
-
sert it into the one-
touch fitting carefully
and securely all the
way to the bottom.
Piping
Caution
Caution
3. Mounting of screws
• The tightening torque of the M3 mounting screw must be 0.5
to 0.7 N·m.
• Do not apply force to the body of the product by mounting.
This may lead to damage to the product.
• Mount the product on a flat, even surface. Mounting on an
uneven surface can damage the case.
• For piping specifications of 01 and N01, close mounting can-
not be applied because of interference between fittings.
• For direct mounting or close mounting, select the fitting with a
wrench flat and øD of 10 mm or less.
Recommended fittings
 One-touch mini Hexagon socket head male connector:
KJS04-M5 (Tubing O.D. ø4, Connection thread M5 x 0.8)
 One-touch fitting Hexagon socket head male connector:
KQ2S04-M5 (Tubing O.D. ø4, Connection thread M5 x 0.8)
• When selecting other fittings, check that there is no interferen-
ce with surrounding equipment and enough space for mainte-
nance. (For details of the fittings, refer to SMC Best Pneuma-
tics)
Caution
Mounting
2. Removal and mounting of DIN rail
• It is necessary to prepare a DIN rail adapter for the mounting
of the DIN rail.
• Take care not to bend the claws of the DIN rail adapter when
mounting.
Engage claw 1 of the product
with the upper part of the DIN
rail and press it downward,
then fit claw 2 of the product
horizontally until it clicks.
Engage claw 1 of the product
with the DIN rail as indicated
by q and pull it to the
direction w, and then fit claw
2 of the product horizontally
until it clicks.
Move to the direction q, and
remove claw 1 as indicated by
w.
Mounting of DIN rail adapter
Mounting of DIN rail
Removal of DIN rail
•
We recommend using an end
plate available from the manufac-
turers shown on the right for
mounting onto the DIN rail. For
the handling and other detailed
information about the end plate,
contact the manufacturer directly.
Manufacturer
OMRON Corp.
IDEC Corp.
Model
PFP-M
BNL6
Series ZSE10
(
F
)
/ISE10
Specific Product Precautions 2
Be sure to read before handling.
Refer to back pages 1 and 2 for Safety Instructions and Handling Precautions for SMC
Products (M-E03-3) for Precautions.
Back page 4