FPC-N64 User Manual M2M Gateway Product Version: 1.0 Date: 2019-11-02 For any question, please contact Chengdu Vantron Technology, Ltd. Copyright © Vantron Technology, Ltd. All rights reserved.
Change History This document describes FPC-N64 briefly and is intended for all readers. This table describes the version and release date. No. Version Description Date Author 1 V1.0 First release.
Foreword Copyright While all information contained herein have been carefully checked to assure its accuracy in technical details and printing, Vantron assumes no responsibility resulting from any error or features of this manual, or from improper uses of this manual or the software. Please contact our technical department for relevant operation solutions if there is any problem that cannot be solved according to this manual.
Limitation of Liability/Non-warranty For direct or indirect damage to this device or other devices of Vantron caused by failure of conforming to this manual or the safety instructions on device label, Vantron assumes neither warranty nor legal liability even if the device is still under warranty. The FPC-N64 should be installed, debugged and maintained by professionals. The outside antennas are not permitted to be installed or to be changed by non-professionals.
Installation: ensure correct installation according to instructions from the manufacturer with recommended installation tools. Ensure ventilation and smoothness according to relevant ventilation standards. Safety Instructions for Power Cables and Accessories Use Proper power source only. Start only with power source that satisfies voltage label and the voltage necessary according to this manual.
Contents 1. Overview .....................................................................................................1 1.1 Introduction .........................................................................................1 1.2 Specifications/Features ......................................................................2 2. FPC-N64 Hardware Instructions .............................................................3 2.1 Product Appearance .............................................................
FPC-N64 User Manual 1. Overview 1.1 Introduction Thank you for choosing Vantron. It is our commitment to provide our valued customers with the embedded devices equipped with the state-of-the-art technology and the best product services. Vantron’s M2M products are based on the most advanced ARM and Intel Atom processors and have low-power consumption and high integration. The products are designed for applications of M2M in industry, finance, retailing, vehicle, transportation, etc.
FPC-N64 User Manual 1.2 Specifications/Features Table 1-1 describes specifications. Table 1-1 Specifications CPU Processor TI, AM3352, ARM Cortex-A8, 32-Bit, 1 GHz Low Power Processor Memory On Board RAM Flash DDR3, 256 MB Bluetooth OPT Bluetooth V4.0, 2.
FPC-N64 User Manual 2. FPC-N64 Hardware Instructions 2.
FPC-N64 User Manual 2.2 Interface Description 2.2.1 Power Interface Figure 2-4 Power connector outlook Pin 1 Table 2-2 Pin description of power connector Pin Description 1 Power input range: DC9-30V or AC24V L 2 DC Ground or AC24V N 3 Shell ground 2.2.2 Ethernet Interface Standard RJ45 interface, supporting 100M Full/Half Duplex, is a standard RJ45 Ethernet port.
FPC-N64 User Manual 2.2.3 RS232 or RS485 Connector Standard vertical 1 x 3 x 3.81 mm male Terminal Block.
FPC-N64 User Manual Table 2-4 Bit description of RS232 or RS485 connector Bit Description 1 Single ON: Have matched with a resistor of 120 ohm Term OFF: No 2 ON: Have pulled up a resistor of 510 ohm Bias- OFF: No 3 ON: Have pulled down a resistor of 510 ohm Bias+ OFF: No 4 ON: Select RS232 Select RS232 or RS485 OFF: Select RS485 2.2.4 RS485 Connector Standard vertical 1 x 3 x 3.81 mm male Terminal Block.
FPC-N64 User Manual Figure 2-9 DIP Switch for selection Table 2-6 Bit description of RS485 connector Bit 1 Description Single ON: Have matched with a resistor of 120 ohm Term OFF: No 2 ON: Have pulled up a resistor of 510 ohm Bias- OFF: No 3 ON: Have pulled down a resistor of 510 ohm Bias+ OFF: No 2.2.
FPC-N64 User Manual 2.2.6 LED PWR LED: If the light is on, the system is successfully started; If the light is off, the system is turned off. ERR LED: User can define by themselves. SS LED: User can define by themselves. TX LED: If R1 sends data, TX1 flashes; if R2 sends data, TX2 flashes. RX LED: If R1 receives data, RX1 flashes; if R2 receives data, RX2 flashes. Figure 2-11 LED 2.2.7 Debug CONN, Pin header,1 x 4 x 2.0, TH. User can view the debug message and use keyboard to input debug command.
FPC-N64 User Manual 2 TTL_TXD 3 TTL_RXD 4 DGND 2.2.8 Renew Button Renew button: Press and hold this button to restore factory settings, and the press time is user-defined. Figure 2-13 Renew button 2.2.9 SD/MMC Socket This is standard SD card socket where user can save data on this storage.
FPC-N64 User Manual 3. Tips Waste Disposal It is recommended to disassemble the device before abandoning it in conformity with local regulations. Please ensure that the abandoned batteries are disposed according to local regulations on waste disposal. Do not throw batteries into fire (explosive) or put in common waste canister.
FPC-N64 User Manual Pay attention to caution signs. Caution signs in this manual remind of possible danger. Please comply with relevant safety tips below each sign. Meanwhile, you should strictly conform to all safety tips for operation environment. Notice Considering that reasonable efforts have been made to assure accuracy of this manual, Vantron assumes no responsibility of possible missing contents and information, errors in contents, citations, examples, and source programs.
FPC-N64 User Manual Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FPC-N64 User Manual IC statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
FPC-N64 User Manual compliance. Cet équipement doit être installé et actionné conformément aux instructions et l’antenne utilisée pour cet émetteur doit être installée pour fournir une distance de séparation d’au moins 20 cm de toutes les personnes et ne doit pas être co-localisée ou exploitée en conjonction avec toute autre antenne ou émetteur.
FPC-N64 User Manual Appendix A: How to Contact Us If you have any problem or want to know more about our products, visit www.vantrontech.com or contact us. US Office: Vantron Technology, Inc. Address: 440 Boulder Court, Suite 300, Pleasanton, CA 94566, USA Tel: 925-621-8758 Email: sales@vantrontech.com China Office: Chengdu Vantron Technology, Ltd Address: 6th Floor, 1st Building, No.
