Datasheet

Action
Fluid
Proof pressure
Maximum operating pressure
Minimum operating pressure
Ambient and fluid temperature
Cushion
Lubrication
Stroke length tolerance
Piston speed
Allowable kinetic energy
ø10
ø16
Specifications
Double acting, Single rod
Air
1.05 MPa
10.7 MPa
0.06 MPa
+1.0
0
Bore size (mm)
10
16
Bore size (mm)
10 16
Standard stroke (mm)
15, 30, 45, 60, 75, 100, 125, 150
15, 30, 45, 60, 75, 100, 125, 150, 175, 200
Standard Stroke
Mounting Style and Accessory
Port Location on Head Cover
Mounting Bracket Part No.
Precautions
1. During installation, secure the rod cover and
tighten by applying an appropriate tightening
force to the retaining but or to the rod cover
body.
If the head cover is secured or the head
cover is tightened, the cover could rotate,
leading to the deviation.
2. Proper tightening torque for mounting thread
should be within the range specified. Apply a
Loctite
®
(no. 242 Blue) for mounting thread.
3. To remove and install the retaining ring for
the knuckle pin or the clevis pin, use an
appropriate pair of pliers (tool for installing a
type C retaining ring).
Especially with ø10, use ultra thin pliers, such
as Super Tool Corp., CSM-07A.
4. For the auto switch mounting rail, do not
remove the pre-equipped rail. Since the
mounting thread is drilled through inside a the
cylinder, it will result in air leakage.
Mounting
Caution
1. It might not be able to control by meter-out at
a low speed operation.
Operating Precautions
Warning
1. For Series CJ2X, 0.1 Nl /min is the values at
maximum in terms of its construction and
there is internal leakage (ANR).
Caution
∗ Pin and retaining ring are shipped together with double clevis and double knuckle joint.
∗ Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.)
Mounting
Mounting nut
Rod end nut
Clevis pin
Single knuckle joint
Double knuckle joint
∗
T-bracket

















Basic
style
Axial foot
style
Rod side
flange style
Double
∗
clevis style
Mounting
bracket
Foot bracket
Flange bracket
T-bracket
∗
Bore size (mm)
10
CJ-L010B
CJ-F010B
CJ-T010B
16
CJ-L016B
CJ-F016B
CJ-T016B
∗ T-bracket is used with double clevis (D).
For basic style, the port position in a head cover is available either perpendicular to the
axis or in-line with the cylinder axis.
Axial direction Perpendicular
Bore size
(mm)
Proper tightening torque for mounting thread
(N·m) (tightening torque for mounting nut)
10
16
3.0 to 3.2
5.4 to 5.9
Without auto switch: –10 to 70°C (No freezing)
With auto switch: –10 to 60°C (No freezing)
Rubber bumper (Standard equipment)
Not required (Non-lube)
1 to 300 mm/s
0.035 J
0.090 J
JIS Symbol
Double acting, Single rod
Be sure to read before handling.
Refer to front matters 42 and 43 for
Safety Instructions and pages 3 to 11
for Actuator and Auto Switch Precau-
tions.
Standard
equipment
Option
1115
Series CJ2X
Low Speed Cylinder
Double Acting, Single Rod
REA
REB
REC
CY
CX
MQ
RHC
RZQ
Individual
-X
D-
-X
P1111-P1166-E.qxd 08.11.17 3:24 PM Page 1115