Datasheet

[Stainless Steel Mounting Screw Kit]
The following set of stainless steel mounting screws is available. Use them in accordance with the operating
environment. (Since auto switch brackets are not included, order them separately.)
BBA4: For D-C7/C8/H7 types
Note 5) Refer to page 1358 for the details of BBA4 screws.
The above stainless steel screws are used when a cylinder is shipped with D-H7BAL-type auto switches.
When only a switch is shipped independently, BBA4 screws are attached.
Reference
Auto switch mounting brackets using stainless steel screws are available for stainless steel cylinder CJ5.
∗ Solid state auto switches are also available with a pre-wired connector. Refer to pages 1328 and 1329 for details.
∗ Normally closed (NC = b contact) solid state auto switches (D-F9G/F9H types) are also available. Refer to page 1290 for details.
Auto switch type Part no. FeaturesElectrical entry (Entry direction)
D-C73, C76
D-C80
D-H7A1, H7A2, H7B
D-H7NW, H7PW, H7BW
—
Without light
—
Diagnosis indication (2 colors)
Grommet (In-line)
In addition to the auto switches listed above, the following auto switches are also available.
Refer to pages 1263 to 1371 for the detailed specifications.
Reed
Sold state
Operating range
Auto Switch Mounting Brackets for CJ5: Part No.
Auto switch mounting bracket part no. Note
Bore size (mm)
10
16
BJ2-010S
BJ2-016S
Stainless steel mounting screw
Auto Switch Mounting Bracket: Part No.
Auto switch model
Bore size
61016
4.5
2
6
3
5
—
—
6
2.5
7
4
8
6
3
8
11
7
3
7
4
9
6.5
3.5
9
13
D-A9첸
D-C7첸/C80/C73C/C80C
D-H7첸/H7첸W
D-H7BAL/H7NF
D-H7C
D-A9첸/A9첸V
D-M9첸/M9첸V
D-M9첸W/M9첸WV
D-M9첸AL/M9첸ALV
D-A7첸/A80/A7H/A80H
D-A73C/A80C
D-F7첸/J79/F7첸W/J79W
D-F7첸V/F7첸WV/F79F
D-J79C/F7BAL/F7BAVL
D-F7NTL
D-A79W
(mm)
— 5 5
—
—
—
BJ2-006 BJ2-010
Note 3), Note 4)
BQ2-012, BQ2-012S
Note 3), Note 4)
BQ2-012, BQ2-012S
BJ2-016
Auto switch
mounting
Bore size (mm)
ø6 ø10 ø16
Auto switch model
Band
mounting
Note 1), Note 2)
BJ2-006 BJ3-1
Note 1), Note 2)
BJ2-010 BJ3-1
Note 1), Note 2)
BJ2-016 BJ3-1
Rail
mounting
D-A9첸
D-M9첸
D-M9첸W
D-C7첸/C80
D-C73C/C80C
D-H7첸/H7첸W
D-H7BAL/H7NF
D-A9첸
D-A9첸V
D-M9첸
D-M9첸V
D-M9첸W
D-M9첸WV
D-M9첸AL
(4)
D-M9첸AVL
(4)
BQ2-012
BQ2-012S
D-M9첸
D-M9첸W
BJ2-
첸첸첸
: A set of a and b above
BJ3-1: A set of c, d and e above
Auto switch
Set screw (Not used)
Switch spacer
(Stainless steel)
e
Switch holder
(Resin)
d
Switch bracket
(Stainless steel)
c
Auto switch mounting screw
b
Auto switch mounting band
a
Band mountingRail mounting
123
∗ Since this is a guideline including hysteresis, not meant
to be guaranteed. (Assuming approximately ±30%
dispersion.) There may be the case it will vary
substantially depending on an ambient environment.
Air Cylinder Series CJ2
Note 1) Two kinds of auto switch bracket are used as a set.
Note 2) When cylinders are shipped, only auto switch mounting brackets are assembled.
Note 3) When a compact auto switch is mounted on a ø10 or ø16 rail, an auto switch bracket is needed, to be
ordered separately.
CDJ2B10-60-A······1
D-M9BWV·············2 pcs.
BQ2-012 ···············2 pcs.
Note 4) For D-M9쏔A(V)L, order BQ2-012S, which uses stainless steel mounting screws.
CJ1
CJP
CJ2
CM2
CG1
MB
MB1
CA2
CS1
CS2
Individual
-X쏔
D-쏔
-X쏔
Technical
data
P0015-P0124-E.qxd 08.10.2 4:03 PM Page 123