Datasheet
How to Order
1
RoHS
Series CJ2
ø10, ø16
Air Cylinder: Standard Type
Double Acting, Single Rod
Made to Order
Refer to page 2 for details.
A
A
∗ Only for CJ2D (double clevis)
∗ Pivot bracket is shipped together
with the product, but not assembled.
Pivot bracket
∗ Mounting bracket is shipped
together with the product,
but not assembled.
∗ Rod end bracket is shipped together with
the product, but not assembled.
∗ A knuckle joint pin is not provided with
the single knuckle joint.
Rod end bracket
∗ For applicable auto switches,
refer to the table below.
∗ For rail mounting, screws and nuts
for 2 auto switches come with the
rail.
∗
Refer to page 84 for auto switch
mounting brackets.
∗ For double clevis, the product is perpendicular to the cylinder axis.
∗
For double-side bossed, the product is perpendicular to the cylinder axis.
Cushion
Head cover port location
Auto switch
Number of auto
switches
Auto switch
mounting type
Standard stroke
Bore size
∗ Manufacture of intermediate strokes in 1 mm
intervals is possible. (Spacers are not used.)
Produced upon receipt of order.
Mounting
Built-in magnet
M9BWN
V
W
BZ6016
Z6016
D
With auto switch
CDJ2
BCJ2
B
Basic
E
Double-side bossed
D
Double clevis
L
Single foot
M
Double foot
F
Rod fl ange
G
Head fl ange
Bore size [mm]
Standard stroke
10
15, 30, 45, 60,
75, 100, 125, 150
16
15, 30, 45, 60, 75,
100, 125, 150, 175, 200
10
10 mm
16
16 mm
—
None
N
Pivot bracket is shipped
together with the product,
but not assembled.
A
Rail mounting
B
Band mounting
—
2 pcs.
S
1 pc.
n
“n” pcs.
—
Without auto switch
—
None
V
Single knuckle joint
W
Double knuckle joint
T
Rod end cap (Flat type)
U
Rod end cap (Round type)
—
Perpendicular
to axis
R
Axial
—
Rubber bumper
A
Air cushion
∗ Since there are other applicable auto switches than listed above, refer to page 85 for details.
∗ For details about auto switches with pre-wired connector, refer to the Auto Switch Guide.
∗ Solid state auto switches marked with “” are produced upon receipt of order.
∗
The D-A9쏔쏔/M9쏔쏔쏔/A7쏔쏔/A80쏔/F7쏔쏔/J7쏔쏔 auto switches are shipped together, (but not assembled). (For band mounting, only the auto switch mounting brackets are assembled before shipment.)
∗∗ Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance.
Please contact SMC regarding water resistant types with the above model numbers.
∗ Lead wire length symbols: 0.5 m·················· — (Example) M9NW
1 m·················· M
(Example) M9NWM
3 m··················
L
(Example) M9NWL
5 m··················
Z
(Example) M9NWZ
None
···············
N
(Example) H7CN
Applicable Auto Switches/Refer to the Auto Switch Guide for further information on auto switches.
Type
Special function
Electrical
entry
Indicator light
Wiring
(Output)
Load voltage Auto switch model Lead wire length [m]
Pre-wired
connector
Applicable
load
DC AC
Band mounting Rail mounting
0.5
(—)
1
[m]
3
(L)
5
(Z)
None
(N)
Perpendicular
In-line
Perpendicular
In-line
Solid state auto switch
——
Grommet
Yes
3-wire (NPN)
24 V
5 V,12 V
—
M9NV M9N M9NV M9N
—
IC circuit
Relay,
PLC
3-wire (PNP)
M9PV M9P M9PV M9P
—
2-wire 12 V
M9BV M9B M9BV M9B
—
—
Connector
—
H7C J79C
—
—
—
Diagnostic indication
(2-colour indication)
Grommet
3-wire (NPN)
5 V,12 V
M9NWV M9NW M9NWV M9NW
—
IC circuit
3-wire (PNP)
M9PWV M9PW M9PWV M9PW
—
2-wire 12 V
M9BWV M9BW M9BWV M9BW
—
—
Water resistant
(2-colour indication)
3-wire (NPN)
5 V,12 V
M9NAV
∗∗
M9NA
∗∗
M9NAV
∗∗
M9NA
∗∗
—
IC circuit
3-wire (PNP)
M9PAV
∗∗
M9PA
∗∗
M9PAV
∗∗
M9PA
∗∗
—
2-wire 12 V
M9BAV
∗∗
M9BA
∗∗
M9BAV
∗∗
M9BA
∗∗
—
—
With diagnostic output (2-colour indication)
4-wire (NPN)
5 V,12 V
—
H7NF
—
F79F
—
—
IC circuit
Reed auto switch
——
Grommet
Yes
3-wire
(NPN equivalent)
—
5 V —
A96V A96 A96V A96
—
—— —
IC circuit
—
2-wire
— 200 V — —
A72 A72H
—
—— —
—
Relay,
PLC
24 V
12 V
100 V
A93V A93 A93V A93
—
——
No
100 V or less
A90V A90 A90V A90
—
—— —
IC circuit
Yes
——
C73C A73C
—
—
——
Connector
No
24 V or less
—
C80C A80C
—
—
—
IC circuit
Diagnostic indication (2-colour indication)
Grommet
Yes
—— — —
A79W
—
—
—— — —