USER GUIDE BARRICADETM N 802.
BarricadeTM N SMCWGBR14-N2 User Guide No. 1, Creation Road III, Hsinchu Science Park, 30077, Taiwan, R.O.C.
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright © 2011 by SMC Networks, Inc. No.
WARRANTY AND PRODUCT REGISTRATION To register SMC products and to review the detailed warranty statement, please refer to the Support Section of the SMC Website at http:// www.smc.com.
COMPLIANCES FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
COMPLIANCES IMPORTANT NOTE: FCC RADIATION EXPOSURE STATEMENT This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be colocated or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations.
COMPLIANCES EUROPE - EU DECLARATION OF CONFORMITY This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: ◆ EN 60950-1:2006 + A11: 2009 Safety of Information Technology Equipment. ◆ EN 300 328 V1.7.
COMPLIANCES This equipment may be operated in: The official CE certificate of conformity can be downloaded by selecting the relevant model/ part number from www.smc.com -> support -> download. Bulgarian Български С настоящето, SMC Networks декларира, че това безжично устройство е в съответствие със съществените изисквания и другите приложими разпоредби на Директива 1999/5/EC.
COMPLIANCES Maltese Malti Hawnhekk, Manufacturer, jiddikjara li dan Radio LAN device jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Polish Polski Niniejszym Manufacturer oświadcza, że Radio LAN device jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
COMPLIANCES PRÉCAUTIONS DE SÉCURITÉ Lisez attentivement les informations suivantes avant d’utiliser votre appareil. Respectez toutes les précautions afin de protéger l’appareil des risques et dégâts provoqués par un incendie et l’alimentation électrique : ◆ Utilisez exclusivement l’adaptateur d’alimentation fourni avec cet appareil. ◆ Faites attention à la puissance de charge de la prise de courant ou des rallonges électriques.
COMPLIANCES ◆ Stellen Sie dieses Gerät nicht in der Nähe von Wärmequellen oder an Orten mit hohen Temperaturen auf. Platzieren Sie das Gerät nicht im direkten Sonnenlicht. ◆ Stellen Sie dieses Gerät nicht an feuchten oder nassen Orten auf. Achten Sie darauf, keine Flüssigkeiten über dem Gerät zu verschütten. ◆ Befolgen Sie die Hinweise im Benutzerhandbuch (bzw. in der Kurzanleitung) zum Anschluß des Gerätes an einen PC oder ein anderes Elektrogerät.
COMPLIANCES PRECAUÇÕES DE SEGURANÇA Leia atentamente as seguintes informações antes de utilizar o dispositivo. Respeite as seguintes indicações de segurança para proteger o dispositivo contra riscos e danos causados por fogo e energia eléctrica: ◆ Utilize o transformador incluído na embalagem do dispositivo. ◆ Respeite a potência da tomada eléctrica e das extensões. Uma tomada eléctrica sobrecarregada ou cabos e fichas danificadas podem causar choques eléctricos ou fogo.
ABOUT THIS GUIDE PURPOSE This guide details the hardware features of the wireless router, including its physical and performance-related characteristics, and how to install the device and use its configuration software. AUDIENCE This guide is for PC users with a working knowledge of computers. You should be familiar with Windows operating system concepts.
CONTENTS WARRANTY AND PRODUCT REGISTRATION 4 COMPLIANCES 5 ABOUT THIS GUIDE 13 CONTENTS 14 1 INTRODUCTION 17 Conventions 18 Main Features 18 Key Hardware Features 19 Package Contents 19 Front Panel 19 LED Indicators 20 Rear Panel 21 Antennas 21 Power Connector 21 Reset Button 21 USB Port 21 Ethernet WAN Port 22 Ethernet LAN Port 22 2 CONNECTING THE ROUTER 23 System Requirements 23 Installation Environment Requirements 23 Connecting the Router 24 3 QUICK INSTALLAT
CONTENTS General Status 35 ARP List 35 Quick Setup 36 5 NETWORK SETTINGS 37 WAN 37 MAC Clone 46 LAN 47 Dynamic DNS 47 Comexe.cn DDNS 48 Dyndns.org DDNS 49 No-ip.
CONTENTS 11 ACCESS CONTROL SETTINGS 90 Rule 90 Host 93 Target 95 Schedule 97 Parental Control 99 12 ADVANCED ROUTING 103 Static Routing List 103 13 QOS SETTINGS 105 QoS Settings 105 Rules List 106 14 SYSTEM TOOLS 107 Time Setting 107 Diagnostic 108 Settings Management 110 Firmware Upgrade 110 Factory Defaults 111 Backup & Restore 111 Reboot 112 Password 113 System Log 114 Statistics 116 Local Management 117 Remote Management 118 A FAQ 120 B CONFIGURING THE
1 INTRODUCTION The SMCWGBR14-N2 Wireless N Gigabit Router integrates a 4-port switch, firewall, NAT router, and wireless access point. The Wireless N Gigabit Router delivers exceptional range and speed, which can fully meet the needs of Small Office/Home Office (SOHO) networks and users demanding higher networking performance. INCREDIBLE SPEED The SMCWGBR14-N2 Wireless N Gigabit Router provides wireless connections up to 300 Mbps with other 802.11n wireless clients.
CHAPTER 1 | Introduction Conventions CONVENTIONS The “Router” or “SMCWGBR14-N2” mentioned in this guide stands for the SMCWGBR14-N2 Wireless N Gigabit Router without any explanation. MAIN FEATURES ◆ Complies with IEEE 802.11n to provide a wireless data rate of up to 300 Mbps. ◆ One 10/100/1000 Mbps Auto-Negotiation RJ-45 WAN port, four 10/ 100/1000 Mbps Auto-Negotiation RJ-45 LAN ports, supporting Auto MDI/MDIX ◆ Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security.
CHAPTER 1 | Introduction Key Hardware Features KEY HARDWARE FEATURES The following table describes the main hardware features of the wireless Router. Table 1: Key Hardware Features Feature Description WAN Port One 1000BASE-T RJ-45 port for connecting to the Internet. LAN Port Four 1000BASE-T RJ-45 ports for local network connections. USB Port One USB slot for USB mass storage device. Reset Button For resetting the unit and restoring factory defaults.
CHAPTER 1 | Introduction Front Panel LED INDICATORS The wireless Router includes ten status LED indicators, as described in the following table. Table 2: LED Behavior LED Status Description Power On The unit is receiving power and is operating normally. Off There is no power currently being supplied to the unit. On The Router is initializing. Flashing The Router is working properly. Off The Router has a system error. On/Flashing The 802.
CHAPTER 1 | Introduction Rear Panel REAR PANEL Figure 2: Rear Panel POWER RESET USB The following items are located on the rear panel (from left to right). ANTENNAS The access point includes integrated MIMO antennas for wireless communications. A MIMO antenna system uses two or more identical antennas to receive and transmit signals, helping to increase data throughput and range.
CHAPTER 1 | Introduction Rear Panel ETHERNET WAN PORT A 1000BASE-T RJ-45 port that can be attached to an Internet access device, such as a DSL or Cable modem. ETHERNET LAN PORT The wireless router has four 1000BASE-T RJ-45 ports that can be attached directly to a PC or 10BASE-T/100BASE-TX/1000BASE-T LAN segments. This port supports automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs, switches, or hubs.
2 CONNECTING THE ROUTER SYSTEM REQUIREMENTS You must meet the following minimum requirements: ◆ Broadband Internet access service (DSL/Cable/Ethernet) ◆ One DSL/Cable modem that has an RJ-45 connector ◆ PCs with working Ethernet adapters and Ethernet cables with RJ-45 connectors ◆ TCP/IP protocol on each PC ◆ Web browser, such as Microsoft Internet Explorer 5.5 or above, Netscape Navigator 4.7 or above, or Mozilla Firefox 1.0 or above.
CHAPTER 2 | Connecting the Router Connecting the Router CONNECTING THE ROUTER Before installing the Router, make sure your PC is successfully connected to the Internet through the broadband service. If there is any problem, first contact your ISP. Install the Router according to the following steps. 1. Power off your PC, Cable/DSL modem, and the Router. 2. Find a good location for the Router. The best place is usually at the center of your network.
CHAPTER 2 | Connecting the Router Connecting the Router Figure 3: Hardware Installation – 25 –
3 QUICK INSTALLATION GUIDE TCP/IP CONFIGURATION This chapter shows you how to quickly configure the basic functions of your SMCWGBR14-N2 Wireless N Gigabit Router using the Quick Setup Wizard. The default IP address of the SMCWGBR14-N2 Wireless N Gigabit Router is 192.168.2.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as needed. In this guide, the default values are used for all descriptions. Connect a local PC to one of the LAN ports on the Router.
CHAPTER 3 | Quick Installation Guide TCP/IP Configuration Figure 4: Success Result of a Ping Command If the displayed result is similar to the following figure, it means the connection between your PC and the Router is not functioning. Figure 5: Failure of a Ping Command To check the connection, follow these steps: 1. Verify that the LAN port LED to which the PC is connected on the Router and the LED on your PC's network adapter are turned on. 2. Verify that the Router's IP address is 192.168.2.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide QUICK INSTALLATION GUIDE With a Web-based (Internet Explorer or Netscape® Navigator) utility, it is easy to configure and manage the SMCWGBR14-N2 Wireless N Gigabit Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser. 1. To access the configuration utility, open a web-browser and type the default address http://192.168.2.1 in the address field of the browser.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide Figure 8: Quick Setup 3. Click Next, and then WAN Connection Type page will appear. Figure 9: Choose WAN Connection Type The Router provides Auto-Detect function and supports three popular ways PPPoE, Dynamic IP, and Static IP, to connect to the Internet. It is recommended that you make use of the Auto-Detect function.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide Figure 10: Quick Setup - PPPoE ■ User Name and Password - Enter the User Name and Password provided by your ISP. These fields are case sensitive. If you have difficulty with this process, please contact your ISP. b. If the connection type detected is Dynamic IP, you can go on with the wireless configuration, as shown in Figure 12 on page 31. c. If the connection type detected is Static IP, the next screen will appear.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide 5. Click Next to continue, the Wireless settings page will appear. Figure 12: Quick Setup - Wireless ◆ Wireless Radio - Enable or disable the wireless radio choosing from the pull-down list. ◆ SSID - Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set to be “SMC”.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide ◆ Max Tx Rate - You can limit the maximum transmission rate of the Router through this field. ◆ Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. It is recommended strongly that you choose one of following options to enable security. ◆ WPA-PSK/WPA2-PSK - Select WPA based on pre-shared passphrase.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide Figure 14: Quick Setup - reboot – 33 –
4 CONFIGURING THE ROUTER This chapter will show each Web page's key functions and the configuration method. LOGIN After your successful login, you will see the twelve main menus on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions. Figure 15: Main Menu The detailed explanations for each Web page’s key function are listed below.
CHAPTER 4 | Configuring the Router Status STATUS GENERAL STATUS The Status page provides the current status information about the Router. All information is read-only. Figure 16: Router Status ARP LIST To manage the computer, you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list, and you could configure the items on the ARP list also. This page displays the ARP List; it shows all the existing IP & MAC Binding entrie.
CHAPTER 4 | Configuring the Router Quick Setup Figure 17: ARP List ◆ MAC Address - The MAC address of the controlled computer in the LAN. ◆ IP Address - The assigned IP address of the controlled computer in the LAN. ◆ Status - Indicates whether or not the MAC and IP addresses are bound. ◆ Configure - Load or delete an item. ■ ■ Load - Load the item to the IP & MAC Binding list. Delete - Delete the item. Click the Bind All button to bind all the current items, available after enable.
5 NETWORK SETTINGS There are five submenus under the Network menu: WAN, MAC Clone, LAN, Dynamic DNS and Binding Settings. Click any of them, and you will be able to configure the corresponding function. WAN Choose menu “Network->WAN”, you can configure the IP parameters of the WAN on the screen below. If your ISP provides the DHCP service, please choose Dynamic IP type, and the Router will automatically get IP parameters from your ISP. You can see the page as follows.
CHAPTER 5 | Network Settings WAN ◆ MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP. ◆ Use These DNS Servers - If your ISP gives you one or two DNS addresses, select Use These DNS Servers and enter the primary and secondary addresses into the correct fields. Otherwise, the DNS servers will be assigned dynamically from your ISP.
CHAPTER 5 | Network Settings WAN ◆ Primary/Secondary DNS - (Optional) Enter one or two DNS addresses in dotted-decimal notation provided by your ISP. If your ISP provides a PPPoE connection, select PPPoE option, then enter the following parameters: Figure 20: WAN-PPPoE ◆ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ◆ Secondary Connection - It’s available only for PPPoE Connection.
CHAPTER 5 | Network Settings WAN ◆ Connect on Demand - In this mode, the Internet connection can be terminated automatically after a specified inactivity period (Max Idle Time) and be re-established when you attempt to access the Internet again. If you want your Internet connection keeps active all the time, please enter “0” in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects.
CHAPTER 5 | Network Settings WAN ◆ MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. ◆ Service Name/AC Name - The service name and AC (Access Concentrator) name, which should not be configured unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work.
CHAPTER 5 | Network Settings WAN ◆ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ◆ Auth Server - Enter the authenticating server IP address or host name. ◆ Auth Domain - Type in the domain suffix server name based on your location. For example: NSW / ACT - nsw.bigpond.net.au VIC / TAS / WA / SA / NT - vic.bigpond.net.au QLD - qld.bigpond.net.
CHAPTER 5 | Network Settings WAN If your ISP provides L2TP connection, please select L2TP option, then enter the following parameters : Figure 23: WAN-L2TP ◆ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ◆ Dynamic IP/ Static IP - Choose either as you are given by your ISP. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately.
CHAPTER 5 | Network Settings WAN ◆ Connect Automatically - Connect automatically after the Router is disconnected. To use this option, click the radio button. ◆ Connect Manually - You can configure the Router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the Router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again.
CHAPTER 5 | Network Settings WAN ◆ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ◆ Dynamic IP/ Static IP - Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name. If you choose static IP and enter the domain name, you should also enter the DNS assigned by your ISP. And click the Save button. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately.
CHAPTER 5 | Network Settings MAC Clone ■ Static IP - Connections which use static IP address assignment. The Router can not detect PPTP/L2TP/BigPond connections with your ISP. If your ISP uses one of these protocols, then you must configure your connection manually. MAC CLONE Choose menu “Network->MAC Clone”, you can configure the MAC address of the WAN on the screen below: Figure 25: MAC Address Clone Some ISPs require that you register the MAC Address of your adapter. Changes are rarely needed here.
CHAPTER 5 | Network Settings LAN LAN Choose menu “Network->LAN”, you can configure the IP parameters of the LAN on the screen as below. Figure 26: LAN Settings ◆ MAC Address - The physical address of the Router, as seen from the LAN. The value can't be changed. ◆ IP Address - Enter the IP address of your Router or reset it in dotteddecimal notation (factory default: 192.168.2.1). ◆ Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.0 as the subnet mask.
CHAPTER 5 | Network Settings Dynamic DNS COMEXE.CN DDNS If the dynamic DNS Service Provider you select is www.comexe.cn, the page will appear. Figure 27: Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1. Type the Domain Name received from your dynamic DNS service provider. 2. Type the User Name for your DDNS account. 3. Type the Password for your DDNS account. 4. Click the Login button to log in to the DDNS service.
CHAPTER 5 | Network Settings Dynamic DNS DYNDNS.ORG DDNS If the dynamic DNS Service Provider you select is www.dyndns.org, the page will appear. Figure 28: Dyndns.org DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from dynamic DNS service provider here. 4. Click the Login button to log in to the DDNS service.
CHAPTER 5 | Network Settings Dynamic DNS NO-IP.COM DDNS If the dynamic DNS Service Provider you select is www.no-ip.com, the page will appear. Figure 29: No-ip.com DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from dynamic DNS service provider. 4. Click the Login button to log in the DDNS service.
CHAPTER 5 | Network Settings Binding Setting BINDING SETTING This page displays the IP & MAC Binding Setting table; you can operate it in accord with your desire. Figure 30: Binding Settings ◆ MAC Address - The MAC address of the controlled computer in the LAN. ◆ IP Address - The assigned IP address of the controlled computer in the LAN. ◆ Bind - Check this option to enable ARP binding for a specific device. ◆ Modify - To modify or delete an existing entry.
CHAPTER 5 | Network Settings Binding Setting 4. Click the Save button to save it. To modify or delete an existing entry, follow the steps below. 1. Find the desired entry in the table. 2. Click Modify or Delete as desired on the Modify column. To find an existing entry, follow the steps below. 1. Click the Find button. 2. Enter the MAC Address or IP Address. 3. Click the Find button in the page as shown in the following figure.
6 WIRELESS SETTINGS There are six submenus under the Wireless menu: Wireless Settings, Wireless Security, Wireless MAC Filtering, Wireless Advanced, Wireless Statistics and WPS. Click any of them, and you will be able to configure the corresponding function. WIRELESS SETTINGS Choose menu “Wireless->Wireless Setting”, you can configure the basic settings for the wireless network on this page. Figure 33: Wireless Settings ◆ SSID - Enter a value of up to 32 characters.
CHAPTER 6 | Wireless Settings Wireless Settings ◆ SSID (2-4) - Up to 4 SSIDs for each BSS can be set, the name can be up to 32 characters. The Multi-SSID function is available only when Enable is checked. ◆ Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field.
CHAPTER 6 | Wireless Settings Wireless Settings ◆ Channel width - Select any channel width from the pull-down list. The default setting is automatic, which can adjust the channel width for your clients automatically. NOTE: If 11b only, 11g only, or 11bg mixed is selected in the Mode field, the Channel Width selecting field will turn grey and the value will become 20M, which is unable to be changed. ◆ Max Tx Rate - You can limit the maximum tx rate of the Router through this field.
CHAPTER 6 | Wireless Settings Wireless Security WIRELESS SECURITY Choose menu “Wireless->Wireless Security”, you can configure the security settings of your wireless network. There are five wireless security modes supported by the Router: WEP (Wired Equivalent Privacy), WPA (Wi-Fi Protected Access), WPA2 (Wi-Fi Protected Access 2), WPA2-PSK (Pre-Shared Key), WPA-PSK (Pre-Shared Key).
CHAPTER 6 | Wireless Settings Wireless Security Figure 36: WEP ■ ■ ■ ■ Type - you can choose the type for the WEP security on the pulldown list. The default setting is Automatic, which can select Open System or Shared Key authentication type automatically based on the wireless station's capability and request. WEP Key Format - Hexadecimal and ASCII formats are provided. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length.
CHAPTER 6 | Wireless Settings Wireless Security NOTE: If you check the WPA/WPA2 radio button and choose TKIP encryption, you will find a notice in red. Figure 37: WPA/WPA2 ◆ ■ Radius Server IP - Enter the IP address of the Radius Server. ■ Radius Port - Enter the port that radius service used. ■ Radius Password - Enter the password for the Radius Server. ■ Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update.
CHAPTER 6 | Wireless Settings Wireless MAC Filtering ■ ■ PSK Passphrase - You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters. Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. Be sure to click the Save button to save your settings on this page.
CHAPTER 6 | Wireless Settings Wireless MAC Filtering Figure 40: Add or Modify Wireless MAC Address Filtering Entry To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0A-EB-00-07-8A. 2. Enter a simple description of the wireless station in the Description field. For example: Wireless station A. 3.
CHAPTER 6 | Wireless Settings Wireless Advanced 1. Click the Enable button to enable this function. 2. Select the radio button: Deny the stations not specified by any enabled entries in the list to access for Filtering Rules. 3. Delete all or disable all entries if there are any entries already. 4.
CHAPTER 6 | Wireless Settings Wireless Advanced to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100. ◆ RTS Threshold - Here you can specify the RTS (Request to Send) Threshold. If the packet is larger than the specified RTS Threshold size, the router will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is 2346.
CHAPTER 6 | Wireless Settings Wireless Statistics WIRELESS STATISTICS Choose menu “Wireless->Wireless Statistics”, you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 43: Wireless Statistics ◆ MAC Address - The connected wireless station's MAC address. ◆ Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN / Disconnected.
CHAPTER 6 | Wireless Settings WPS Figure 44: WPS ◆ WPS Status - Enable or disable the WPS function here. ◆ Current PIN - The current value of the Router's PIN displayed here. The default PIN of the Router can be found in the label or User Guide. ◆ Restore PIN - Restore the PIN of the Router to its default. ◆ Gen New PIN - Click this button, and then you can get a new random value for the Router's PIN. You can ensure the network security by generating a new PIN.
CHAPTER 6 | Wireless Settings WPS Figure 45: WPS button 2. Press and hold the WPS button of the adapter directly for 2 or 3 seconds, then the adapter will connect to the router by WPS automatically. Figure 46: WPS button Method Two: 1. Press the WPS button on the front panel of the Router. Figure 47: WPS button 2. For the configuration of the wireless adapter, please choose Push the button on my access point in the configuration utility of the WPS as below, and click Next.
CHAPTER 6 | Wireless Settings WPS Figure 48: The WPS Configuration Screen of Wireless Adapter 3. Wait for a while until the next screen appears. Click Finish to complete the WPS configuration.
CHAPTER 6 | Wireless Settings WPS Method Three: 1. Keep the default WPS Status as Enabled and click the Add device button in Figure 44, then the following screen will appear. Figure 50: Add a New Device 2. Choose Press the button of the new device in two minutes and click Connect. 3. For the configuration of the wireless adapter, please choose Push the button on my access point in the configuration utility of the WPS as below, and click Next.
CHAPTER 6 | Wireless Settings WPS 4. Wait for a while until the next screen appears. Click Finish to complete the WPS configuration.
CHAPTER 6 | Wireless Settings WPS By PIN If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods. Method One: Enter the PIN into my Router 1. Keep the default WPS Status as Enabled and click the Add device button in Figure 44, then the following screen will appear. Figure 53: Add a New Device 2. Choose Enter the new device's PIN and enter the PIN code of the wireless adapter in the field behind PIN in the above figure.
CHAPTER 6 | Wireless Settings WPS Figure 54: The WPS Configuration Screen of Wireless Adapter NOTE: In this example, the default PIN code of this adapter is 26499123 as the above figure shown. Method Two: Enter the PIN from my Router 1. Get the Current PIN code of the Router. (Each router has its unique PIN code. Here takes the PIN code 12345670 of this Router for example). 2.
CHAPTER 6 | Wireless Settings WPS Figure 55: The WPS Configuration Screen of Wireless Adapter NOTE: The default PIN code of the Router can be found in its label or the WPS configuration screen as Figure 44. 3. Then the new device successfully connected to the network. NOTE: The status LED on the Router will light green all the time if the device has been successfully added to the network. The WPS function cannot be configured if the Wireless Function of the Router is disabled.
7 DHCP SETTINGS There are three submenus under the DHCP menu: DHCP Settings, DHCP Clients List and Address Reservation. Click any of them, and you will be able to configure the corresponding function. DHCP SETTINGS Choose menu “DHCP->DHCP Settings”, you can configure the DHCP Server on the page. The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router on the LAN.
CHAPTER 7 | DHCP Settings DHCP Clients List ◆ Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP Address. Enter the amount of time in minutes and the user will be "leased" this dynamic IP Address. After the time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. ◆ Default Gateway - (Optional.
CHAPTER 7 | DHCP Settings Address Reservation You cannot change any of the values on this page. To update this page and to show the current attached devices, click the Refresh button. ADDRESS RESERVATION Choose menu “DHCP->Address Reservation”, you can view and add a reserved addresses for clients via the following figure.When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server.
CHAPTER 7 | DHCP Settings Address Reservation To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2. Modify the information. 3. Click the Save button. Click the Enable/ Disabled All button to make all entries enabled/disabled Click the Delete All button to delete all entries Click the Next button to go to the next page and Click the Previous button to return the previous page.
8 USB STORAGE SETTINGS There are two submenus under the Network Sharing menu: Sharing Service and User Accounts. Click any of them, and you will be able to configure the corresponding function. SHARING SERVICE Choose menu “Network Sharing->Sharing Service”, you can configure a USB disk drive attached to the Router on this page. Figure 60: Network Sharing ◆ Service Status - Indicates the Network Sharing service's current status. ◆ Volume - The volume name of the USB drive the users have access to.
CHAPTER 8 | USB Storage Settings Sharing Service Click the Start button to start the Network Sharing service. Click the Stop button to stop the Network Sharing service. Click the Eject Disk button to safely remove the USB storage device that is connected to USB port. This takes the drive offline. A message will appear on your web browser when it is safe to detach the USB disk. Click the Rescan button to start a new scan. Follow the instructions below to set up your Router as a file server: 1.
CHAPTER 8 | USB Storage Settings User Accounts Figure 62: Sharing Settings - Edit NOTE: The Router cannot automatically locate new USB drive. You have to click the Rescan button manually to display a list of volumes and information about them. NOTE: The new settings will not take effect until you restart the service. NOTE: To unplug the USB drive, click Eject Disk button first. Simply pulling USB drive out of the USB port can cause damage to the device and loss of data.
CHAPTER 8 | USB Storage Settings User Accounts Figure 63: User Accounts ◆ User Name - Type the user name that you want to give access to the USB drive. The user name must be composed of alphanumeric symbols not exceeding 15 characters in length. ◆ Password - Enter the password in the Password field. The password must be composed of alphanumeric symbols not exceeding 15 characters in length. For security purposes, the password for each user account is not displayed.
9 SPECIAL APPLICATION SETTINGS There are four submenus under the Special Application menu: Virtual Servers, Port Triggering, DMZ and UPnP. Click any of them, and you will be able to configure the corresponding function. VIRTUAL SERVERS Choose menu “Special Application->Virtual Servers”, you can view and add virtual servers in the following screen. Virtual servers can be used for setting up public services on your LAN, such as DNS, Email and FTP.
CHAPTER 9 | Special Application Settings Virtual Servers To setup a virtual server entry: 1. Click the Add New button. 2. Select the service you want to use from the Common Service Port list. If the Common Service Port list does not have the service that you want to use, type the number of the service port or service port range in the Service Port box. 3. Type the IP Address of the computer in the IP Address box. 4. Select the protocol used for this application, either TCP or UDP, or All. 5.
CHAPTER 9 | Special Application Settings Port Triggering NOTE: If you set the service port of the virtual server as 80, you must set the Web management port on System Tools –> Remote Management page to be any other value except 80 such as 8080. Otherwise there will be a conflict to disable the virtual server. PORT TRIGGERING Choose menu “Special Application->Port Triggering”, you can view and add port triggering in the following screen.
CHAPTER 9 | Special Application Settings Port Triggering ◆ Status - The status of this entry either Enabled or Disabled. To add a new rule, follow the steps below. 1. Click the Add New button. 2. Select a common application from the Common Applications drop-down list, then the Trigger Port field and the Incoming Ports field will be automatically filled. If the Common Applications do not have the application you need, enter the Trigger Port and the Incoming Ports manually. 3.
CHAPTER 9 | Special Application Settings DMZ NOTE: 1. When the trigger connection is released, the according opening ports will be closed. 2. Each rule allowed to be used only by one host on LAN synchronously. The trigger connection of other hosts on LAN will be refused. 3. Incoming Port Range cannot overlap each other. DMZ Choose menu “Special Application->DMZ”, you can view and configure DMZ host in the screen.
CHAPTER 9 | Special Application Settings UPnP UPNP Choose menu “Special Application->UPnP”, you can view the information about UPnP(Universal Plug and Play) in the screen. The UPnP feature allows the devices, such as Internet computers, to access the local host resources or devices as needed. UPnP devices can be automatically discovered by the UPnP service application on the LAN. Figure 69: UPnP Settings ◆ Current UPnP Status - UPnP can be enabled or disabled by clicking the Enable or Disable button.
10 SECURITY SETTINGS There are two submenus under the Security menu: Basic Security, and Advanced Security. Click any of them, and you will be able to configure the corresponding function. BASIC SECURITY Choose menu “Security->Basic Security”, you can configure the basic security in the following screen. Figure 70: Basic Security Settings ◆ Firewall - A firewall protects your network from the outside world. Here you can enable or disable the Router’s firewall.
CHAPTER 10 | Security Settings Basic Security factory default. If you want all the computers on the LAN exposed to the outside world, you can disable it. ◆ VPN - VPN Passthrough must be enabled if you want to allow VPN tunnels using IPSec, PPTP, or L2TP protocols to pass through the Router’s firewall. ■ ■ ■ ◆ PPTP Passthrough - Point-to-Point Tunneling Protocol (PPTP) allows the Point-to-Point Protocol (PPP) to be tunneled through an IP network.
CHAPTER 10 | Security Settings Advanced Security ADVANCED SECURITY Choose menu “Security->Advanced Security”, you can protect the Router from being attacked by TCP-SYN Flood, UDP Flood and ICMP-Flood in the following screen. Figure 71: Advanced Security Settings ◆ Packets Statistics Interval (5~60) - The default value is 10. Select a value between 5 and 60 seconds from the drop-down list. The Packets Statistics Interval value indicates the time section of the packets statistics.
CHAPTER 10 | Security Settings Advanced Security ◆ ICMP-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600. When the current ICMP-FLOOD Packets number is beyond the set value, the Router will startup the blocking function immediately. ◆ Enable UDP-FLOOD Filtering - Enable or Disable the UDP-FLOOD Filtering. ◆ UDP-FLOOD Packets Threshold (5~3600) - The default value is 500. Enter a value between 5 ~ 3600.
11 ACCESS CONTROL SETTINGS There are five submenus under the Access Control menu: Rule, Host, Target, Schedule and Parental Control. Click any of them, and you will be able to configure the corresponding function. RULE Choose menu “Access Control->Rule”, you can view and set Access Control rules in the screen as shown in the following.
CHAPTER 11 | Access Control Settings Rule ◆ Status - This field displays the status of the rule. Enabled means the rule will take effect, Disabled means the rule will not take effect. ◆ Modify - Here you can edit or delete an existing rule. To add a new rule, please follow the steps below. 1. Click the Add New button and the next screen will pop-up. 2. Give a name (e.g. Rule_1) for the rule in the Rule Name field. 3.
CHAPTER 11 | Access Control Settings Rule Figure 73: Add or Modity Internet Access Control Entry For example: If you desire to allow the host with MAC address 00-11-2233-44-AA to access www.google.com only from 18:00 to 20:00 on Saturday and Sunday, and forbid other hosts in the LAN to access the Internet, you should follow the settings below: 1. Click “Access Control->Host” in the left to enter the Host Settings page.
CHAPTER 11 | Access Control Settings Host ■ Click Save to complete the settings. Then you will go back to the Access Control Rule Management page and see the following list. Figure 74: Display Access Control Entry HOST Choose menu “Access Control->Host”, you can view and set a Host list in the following screen. The host list is necessary for the Access Control Rule. Figure 75: Host Settings ◆ Host Description - Here displays the description of the host and this description is unique.
CHAPTER 11 | Access Control Settings Host 2) In MAC Address field, enter the MAC address. 3. Click the Save button to complete the settings. Click the Delete All button to delete all the entries in the table. Click the Next button to go to the next page, or click the Previous button return to the previous page.
CHAPTER 11 | Access Control Settings Target Figure 78: Host Settings TARGET Choose menu “Access Control->Target”, you can view and set a Target list in the screen as shown in the following figure. The target list is necessary for the Access Control Rule. Figure 79: Target Settings ◆ Target Description - Here displays the description about the target and this description is unique. ◆ Information - The target can be IP address, port, or domain name. ◆ Modify - To modify or delete an existing entry.
CHAPTER 11 | Access Control Settings Target ■ If you select Domain Name, the screen shown is Figure 80. 1) In Target Description field, create a unique description for the target (e.g. Target_1). 2) In Domain Name field, enter the domain name, either the full name or the keywords (for example google) in the blank. Any domain name with keywords in it (www.google.com, www.google.cn) will be blocked or allowed. You can enter 4 domain names. 3. Click the Save button.
CHAPTER 11 | Access Control Settings Schedule For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA in the LAN to access www.google.com only, you should first follow the settings below: 1. Click the Add New button. 2. In Mode field, select Domain Name from the drop-down list. 3. In Target Description field, create a unique description for the target (e.g. Target_1). 4. In Domain Name field, enter www.google.com. 5. Click Save to complete the settings.
CHAPTER 11 | Access Control Settings Schedule To add a new schedule, follow the steps below. 1. Click the Add New button shown in Figure 82 and the next screen will pop-up. 2. In Schedule Description field, create a unique description for the schedule (e.g. Schedule_1). 3. In Day field, select the day or days you need. 4. In Time field, you can select all day-24 hours or you may enter the Start Time and Stop Time in the corresponding field. 5. Click Save to complete the settings.
CHAPTER 11 | Access Control Settings Parental Control 5. Click Save to complete the settings. Then you will go back to the Schedule Settings page and see the following list. Figure 85: Advanced Schedule Settings PARENTAL CONTROL Choose menu “Parental Control”, and you can configure the parental control in the screen as shown in the following figure.
CHAPTER 11 | Access Control Settings Parental Control ◆ Schedule - The time period allowed for the PC controlled to access the Internet. For detailed information, please go to “Access Control ? Schedule”. ◆ Modify - Here you can edit or delete an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New button. 2. Enter the MAC address of the PC (e.g. 00-11-22-33-44-AA) you’d like to control in the MAC Address of Child PC field.
CHAPTER 11 | Access Control Settings Parental Control Figure 87: Add or Modify Parental Control Entry For example: If you desire that the child PC with MAC address 00-11-2233-44-AA can access www.google.com on Saturday only while the parent PC with MAC address 00-11-22-33-44-BB is without any restriction, you should follow the settings below. 1. Click “Parental Control” menu on the left to enter the Parental Control Settings page.
CHAPTER 11 | Access Control Settings Parental Control ■ ■ Select “Schedule_1” you create just now from the Effective Time drop-down list. In Status field, select Enable. 4. Click Save to complete the settings. Then you will go back to the Parental Control Settings page and see the following list, as shown in the following figure.
12 ADVANCED ROUTING STATIC ROUTING LIST Choose menu “Advanced Routing”, you can configure the static route in the next screen. A static route is a pre-determined path that network information must travel to reach a specific host or network. Figure 89: Static Routing To add static routing entries: 1. Click the Add New button. Figure 90: Add or Modify a Static Route Entry 2.
CHAPTER 12 | Advanced Routing Static Routing List 3. Select Enabled or Disabled for this entry on the Status pull-down list. 4. Click the Save button to make the entry take effect. Other configurations for the entries: Click the Delete button to delete the entry. Click the Enable All button to enable all the entries. Click the Disable All button to disable all the entries. Click the Delete All button to delete all the entries.
13 QOS SETTINGS There are two submenus under the QoS menu: QoS Settings and Rules List. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. QOS SETTINGS Choose menu “QoS->QoS Settings”, you can configure the Egress Bandwidth and Ingress Bandwidth in the next screen. Their values you configure should be less than 100000Kbps.
CHAPTER 13 | QoS Settings Rules List RULES LIST Choose menu “QoS->Rules List”, you can view and configure the QoS rules in the screen below. Figure 92: QoS Rules List ◆ Description - This is the information about the rules such as address range. ◆ Egress bandwidth - This field displays the max and mix upload bandwidth through the WAN port, the default is 0. ◆ Ingress bandwidth - This field displays the max and mix download bandwidth through the WAN port, the default is 0.
14 SYSTEM TOOLS Choose menu “System Tools”, and you can see the submenus under the main menu: Time Settings, Diagnostic, Setting Management, Password, System Log, Statistics, Local Management and Remote Management. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. TIME SETTING Choose menu “System Tools->Time Setting”, you can configure the time on the following screen.
CHAPTER 14 | System Tools Diagnostic 3. Click Save to save the configuration. To configure the system automatically: 1. Select your local time zone. 2. Enter the IP address for NTP Server Prior. 3. Click the Get GMT button to get system time from Internet if you have connected to the Internet. NOTE: This setting will be used for some time-based functions such as firewall. You must specify your time zone once you login to the router successfully, otherwise, these functions will not take effect.
CHAPTER 14 | System Tools Diagnostic ◆ Diagnostic Tool - Check the radio button to select one diagnostic too. ■ ■ Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. Traceroute - This diagnostic tool tests the performance of a connection. NOTE: You can use ping/traceroute to test both numeric IP address or domain name.
CHAPTER 14 | System Tools Settings Management SETTINGS MANAGEMENT FIRMWARE UPGRADE Choose menu “System Tools->Firmware Upgrade”, you can update the latest version of firmware for the Router on the following screen. Figure 97: Firmware Upgrade ◆ Firmware Version - This displays the current firmware version. ◆ Hardware Version - This displays the current hardware version. The hardware version of the upgrade file must accord with the Router’s current hardware version.
CHAPTER 14 | System Tools Settings Management FACTORY DEFAULTS Choose menu “System Tools-> Factory Defaults”, and you can restore the configurations of the Router to factory defaults on the following screen. Figure 98: Restore Factory Default Click the Restore button to reset all configuration settings to their default values. ◆ The default User Name: admin ◆ The default Password: smcadmin ◆ The default IP Address: 192.168.2.1 ◆ The default Subnet Mask: 255.255.255.
CHAPTER 14 | System Tools Settings Management NOTE: The current configuration will be covered by the uploading configuration file. The upgrade process lasts for 20 seconds and the Router will restart automatically. Keep the Router on during the upgrading process to prevent any damage. REBOOT Choose menu “System Tools->Reboot”, you can click the Reboot button to reboot the Router via the next screen.
CHAPTER 14 | System Tools Password PASSWORD Choose menu “System Tools->Password”, you can change the factory default user name and password of the Router in the next screen as shown in the following figure. Figure 101: Password It is strongly recommended that you should change the factory default user name and password of the Router, because all users who try to access the Router's Web-based utility or Quick Setup will be prompted for the Router's default user name and password.
CHAPTER 14 | System Tools System Log SYSTEM LOG Choose menu “System Tools->System Log”, you can view the logs of the Router. Figure 102: System Log ◆ Auto Mail Feature - Indicates whether auto mail feature is enabled or not. ◆ Mail Settings - Set the receiving and sending mailbox address, server address, validation information as well as the timetable for Auto Mail Feature, as shown in Figure 101. ◆ Log Type - By selecting the log type, only logs of this type will be shown.
CHAPTER 14 | System Tools System Log Figure 103: Mail Account Settings ◆ From - Your mail box address. The Router would connect it to send logs. ◆ To - Recipient’s address. The destination mailbox where the logs would be received. ◆ SMTP Server - Your smtp server. It corresponds with the mailbox filled in the From field. You can log on the relevant website for Help if you are not clear with the address. ◆ Authentication - Most SMTP Server requires Authentication.
CHAPTER 14 | System Tools Statistics Click Back to return to the previous page. Click the Next button to go to the next page, or click the Previous button return to the previous page. STATISTICS Choose menu “System Tools->Statistics”, you can view the statistics of the Router, including total traffic and current traffic of the last Packets Statistic Interval. Figure 104: Statistics ◆ Current Statistics Status - Enable or Disable. The default value is disabled. To enable, click the Enable button.
CHAPTER 14 | System Tools Local Management Table 3: Statistics Table (Continued) Bytes The total amount of bytes received and transmitted in the last Packets Statistic interval seconds. ICMP Tx The total amount of the ICMP packets transmitted to WAN in the last Packets Statistic interval seconds. UDP Tx The total amount of the UDP packets transmitted to WAN in the last Packets Statistic interval seconds.
CHAPTER 14 | System Tools Remote Management By default, the radio button “All the PCs on the LAN are allowed to access the Router's Web-Based Utility” is checked. If you want to allow PCs with specific MAC Addresses to access the Setup page of the Router's WebBased Utility locally from inside the network, check the radio button “Only the PCs listed can browse the built-in web pages to perform Administrator tasks”, and then enter each MAC Address in a separate field.
CHAPTER 14 | System Tools Remote Management ◆ Remote Management IP Address - This is the current address you will use when accessing your Router from the Internet. This function is disabled when the IP address is set to the default value of 0.0.0.0. To enable this function change 0.0.0.0 to a valid IP address. If set to 255.255.255.255, then all the hosts can access the Router from internet.
A FAQ How do I configure the Router to access Internet by ADSL users? 1. First, configure the ADSL Modem configured in RFC1483 bridge model. 2. Connect the Ethernet cable from your ADSL Modem to the WAN port on the Router. The telephone cord plugs into the Line port of the ADSL Modem. 3. Login to the Router, click the “Network” menu on the left of your browser, and click "WAN" submenu. On the WAN page, select “PPPoE” for WAN Connection Type.
APPENDIX A | FAQ How do I configure the Router to access Internet by Ethernet users? 1. Login to the Router, click the “Network” menu on the left of your browser, and click "WAN" submenu. On the WAN page, select “Dynamic IP” for "WAN Connection Type", finish by clicking “Save”. 2. Some ISPs require that you register the MAC Address of your adapter, which is connected to your cable/DSL Modem during installation.
APPENDIX A | FAQ Figure 111: Virtual Servers NOTE: Your opposite side should call your WAN IP, which is displayed on the “Status” page. 4. How to enable DMZ Host: Log in to the Router, click the “Special Application” menu on the left of your browser, and click "DMZ" submenu. On the "DMZ" page, click Enable radio button and type your IP address into the “DMZ Host IP Address” field, using 192.168.2.169 as an example, remember to click the Save button. Figure 112: DMZ 5.
APPENDIX A | FAQ Figure 113: Basic Security I want to build a WEB Server on the LAN, what should I do? 1. Because the WEB Server port 80 will interfere with the WEB management port 80 on the Router, you must change the WEB management port number to avoid interference. 2. To change the WEB management port number: Log in to the Router, click the “Security” menu on the left of your browser, and click "Remote Management" submenu.
APPENDIX A | FAQ 3. Log in to the Router, click the “Special Application” menu on the left of your browser, and click the "Virtual Servers" submenu. On the "Virtual Servers" page, Click the Add New button, then on the “Add or Modify a Virtual Server” page, enter “80” into the blank next to the “Service Port”, and your IP address next to the “IP Address”, assuming 192.168.2.188 for an example, remember to Enable and Save.
B CONFIGURING THE PCS In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if needed. 1. Install TCP/IP component a. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel. b. Click the Network and Internet Connections icon, and then click on the Network Connections tab in the appearing window. c.
APPENDIX B | Configuring the PCs Figure 118: Select TCP/IP 1.5 The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.
APPENDIX B | Configuring the PCs Setting IP address manually 1. Select Use the following IP address radio button. And the following items available 2. If the Router's LAN IP address is 192.168.2.1, type IP address is 192.168.2.x (x is from 2 to 254), and Subnet mask is 255.255.255.0. 3. Type the Router’s LAN IP address (the default IP is 192.168.2.1) into the Default gateway field. 4. Select Use the following DNS server addresses radio button.
C HARDWARE SPECIFICATIONS STANDARDS IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T 802.11b 802.11g 802.11n PROTOCOL TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP NUMBER OF PORTS 1 10/100/1000 Mbps Auto-Negotiation WAN RJ-45 port 4 10/100/1000 Mbps Auto-Negotiation LAN RJ-45 ports supporting Auto MDI/MDIX 1 USB 2.
APPENDIX C | Hardware Specifications MODULATION DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM SECURITY WEP/WPA/WPA2/WPA2-PSK/WPA-PSK SENSITIVITY @PER 270M: -68dBm@10% PER; 130M: -68dBm@10% PER 108M: -68dBm@10% PER; 54M: -68dBm@10% PER 11M: -85dBm@8% PER; 6M: -88dBm@10% PER 1M: -90dBm@8% PER RF POWER 20dBm (max EIRP) ANTENNA GAIN 3dBi*3 TEMPERATURE Operating: 0 °C to 40 °C (32 to 104 °F) Storage: -40 °C to 70 °C (-40 to 158 °F) HUMIDITY Operating: 10% to 90% (non-condensing) Storge: 5%-90% (non-condensing) – 1
GLOSSARY IEEE 802.11B A wireless standard that supports wireless communications in the 2.4 GHz band using Direct Sequence Spread Spectrum (DSSS). The standard provides for data rates of 1, 2, 5.5, and 11 Mbps. IEEE 802.11G A wireless standard that supports wireless communications in the 2.4 GHz band using Orthogonal Frequency Division Multiplexing (OFDM). The standard provides for data rates of 6, 9, 12, 18, 24, 36, 48, 54 Mbps. IEEE 802.11g is also backward compatible with IEEE 802.11b. IEEE 802.
GLOSSARY ISP (INTERNET SERVICE A company that provides access to the Internet. PROVIDER) MTU (MAXIMUM The size in bytes of the largest packet that can be transmitted. TRANSMISSION UNIT) NAT (NETWORK NAT technology translates IP addresses of a local area network to a ADDRESS TRANSLATION) different IP address for the Internet. PPPOE (POINT TO POINT PPPoE is a protocol for connecting remote hosts to the Internet over an PROTOCOL OVER always-on connection by simulating a dial-up connection.
Headquarters & Sub-Sahara Africa Office No. 1, Creation Rd. III Hsinchu Science Park Taiwan 30077 Tel: +886 3 5770270 Fax: +886 3 5780764 Asia-Pacific Office 1 Coleman Street #07-09, The Adelphi Singapore 179803 Tel: +65-63387667 Fax: +65-63387767 SMC NETWORKS TECHNICAL SUPPORT From Singapore in English and Tel: +65-63387667, Ext. 4 (Mon.-Fri. 9 AM to 5 PM) From the United Arab Emirates in English (Sun.-Thu. 9 AM to 6 PM) Tel: +971 800 222866/+971 4 3564810 From U.S.A.
