USER GUIDE BARRICADE™ N 150Mbps 4-Port Wireless Broadband Router SMCWBR14S-N5
Wireless Broadband Router User Guide No. 1, Creation Road III, Hsinchu Science Park, 30077, Taiwan, R.O.C.
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright © 2012 by SMC Networks, Inc. No.
WARRANTY AND PRODUCT REGISTRATION To register SMC products and to review the detailed warranty statement, please refer to the Support Section of the SMC Website at http:// www.smc.com.
COMPLIANCES FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Country Restriction Reason/Remark Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of NyÅlesund Russian Federation None Only for indoor applications NOTE: Do not use the product outdoors in France. EUROPE - EU DECLARATION OF CONFORMITY This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 - 2483.5 MHz.
German Deutsch Hiermit erklärt SMC Networks, dass sich dieser/diese/dieses Radio LAN device in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi) Hiermit erklärt SMC Networks die Übereinstimmung des Gerätes Radio LAN device mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG.
◆ Proper space for heat dissipation is necessary to avoid any damage caused by device overheating. The ventilation holes on the device are designed for heat dissipation to ensure that the device works normally. Do not cover these ventilation holes. ◆ Do not put this device close to a place where a heat source exits or high temperature occurs. Avoid placing the device in direct sunshine. ◆ Do not put this device close to a place which is damp or wet. Do not spill any fluid on this device.
SICHERHEITSMAßNAHMEN Lesen Sie vor der Inbetriebnahme des Gerätes aufmerksam die nachstehenden Informationen. Bitte befolgen Sie die nachstehenden Sicherheitsmaßnahmen, damit das Gerät nicht beschädigt wird oder Gefahren durch Brand oder elektrische Energie entstehen: ◆ Verwenden Sie nur das beim Gerät mitgelieferte Netzteil. ◆ Achten Sie auf die Last der Steckdose oder des Verlängerungskabels. Eine überlastete Steckdose oder beschädigte Kabel und Stecker können Stromschläge und Brand verursachen.
◆ Deje un espacio adecuado para que se disipe el calor y evitar así cualquier daño en el dispositivo causado por sobrecalentamiento. Los orificios de ventilación del dispositivo están diseñados para disipar el calor y garantizar que dicho dispositivo funciona con normalidad. No tape estos orificios de ventilación. ◆ No coloque este dispositivo cerca de un lugar donde haya una fuente de calor o temperaturas elevadas. Evite exponer el dispositivo a la luz solar directa.
BSMI NOTICE 在進行安裝及設定之前，建議您先閱讀以下注意事項： 1. 確認寬頻的線路是否正常：請先確認當 ADSL 或 Cable 或是對外的線路，直接結到您 的電腦時，是否能正常的連接到網際網路。 2. 移除撥號軟體：若您已經安裝 ISP 所提供的 ADSL 撥接（號）軟體，請先將其移除后 再開始進行連線設定。 3. 系統需求：本產品只需要使用網頁瀏覽器 （Browser）來進行設定安裝，不需要額 外安裝任何程式，在開始設定之前，建議您使用 Internet Explorer 6.0 或更新的 版本來進行安裝設定。 4. 設定時無需連上網際網路 （Internet），只需要透過區域連線 （LAN）即可進行設 定。 ※ 僅需從電腦端拉一條網路線連接至 SMCWBR14S-N5 的 LAN 埠，WAN 埠則先不 要連上 ISP 線路。此動作作用是用來確認您可以正常連到此設備。 5.
ABOUT THIS GUIDE PURPOSE This guide details the hardware features of the wireless router, including its physical and performance-related characteristics, and how to install the device and use its configuration software. AUDIENCE This guide is for PC users with a working knowledge of computers. You should be familiar with Windows operating system concepts.
ABOUT THIS GUIDE ◆ Add BSMI Notice to the Compliances section. SEPTEMBER 2012 REVISION This is the fourth revision of this guide. It includes the following change: ◆ Updated the Compliances section. NOVEMBER 2011 REVISION This is the third revision of this guide. It includes the following change: ◆ Updated the Compliances section. SEPTEMBER 2011 REVISION This is the second revision of this guide. It includes the following change: ◆ Updated the Compliances section.
CONTENTS WARRANTY AND PRODUCT REGISTRATION 4 COMPLIANCES 5 ABOUT THIS GUIDE 14 CONTENTS 16 FIGURES 19 TABLES 23 1 INTRODUCTION 24 Overview of the Router 24 Main Features 25 Key Hardware Features 25 Package Contents 26 Front Panel 26 LED Indicators 26 WPS Button 27 Rear Panel 27 Wireless Antennas 27 Power 27 Ethernet WAN Port 28 Ethernet LAN Ports 28 2 CONNECTING THE ROUTER 29 System Requirements 29 Installation Environment Requirements 29 Connecting the Router 2
CONTENTS Quick Installation Guide 4 CONFIGURING THE ROUTER 34 40 Login 40 Status 41 Quick Setup 42 WPS 42 Operation Mode 49 Network 50 LAN 50 WAN 51 MAC Clone (Router Mode Only) 59 Wireless 59 Wireless Settings (Router Mode) 60 Wireless Settings (Client Mode) 62 Wireless Security 64 Wireless MAC Filtering 68 Wireless Advanced Wireless Statistics 70 72 DHCP 72 DHCP Settings 73 DHCP Clients List 74 Address Reservation 74 Forwarding 76 Virtual Servers 76 Port Trig
CONTENTS Rule 89 Host 92 Target 94 Schedule 97 Advanced Routing 99 Bandwidth Control 100 IP & MAC Binding 101 Binding Setting 102 ARP List 103 DDNS 104 System Tools 107 Time Settings 107 Diagnostic 109 Firmware Upgrade 110 Factory Defaults 111 Backup & Restore 112 Reboot 112 Password 113 System Log 114 Statistics 116 A CONFIGURING THE PC 118 Install TCP/IP Components B FAQ 118 122 How do I configure the Router for Internet access by ADSL users? 122 How do I c
FIGURES Figure 1: Front Panel 26 Figure 2: Rear Panel 27 Figure 3: Router Mode 30 Figure 4: Client Router Mode 31 Figure 5: Success Result of a Ping Command 33 Figure 6: Failure of a Ping Command 33 Figure 7: Log in to the Router 34 Figure 8: Windows Login 34 Figure 9: Quick Setup 35 Figure 10: Operation Mode 35 Figure 11: Choose the WAN Connection Type 35 Figure 12: Quick Setup – PPPoE 36 Figure 13: Quick Setup - Static IP 36 Figure 14: Quick Setup – Wireless 37 Figure 15: Quic
CONTENTS Figure 32: Operation Mode 49 Figure 33: The Network Menu 50 Figure 34: LAN 50 Figure 35: WAN-Dynamic IP 51 Figure 36: WAN-Static IP 52 Figure 37: WAN-PPPoE 53 Figure 38: WAN-PPPoE Advanced Settings 55 Figure 39: WAN-L2TP 56 Figure 40: WAN-PPTP 57 Figure 41: MAC Address Clone 59 Figure 42: Wireless Menu 60 Figure 43: Wireless Settings (Router Mode) 60 Figure 44: Note Dialog 61 Figure 45: Enable WDS 62 Figure 46: Wireless Settings (Client Router Mode) 63 Figure 47: Wire
CONTENTS Figure 68: The Security Menu 82 Figure 69: Basic Security 82 Figure 70: Advanced Security 83 Figure 71: Local Management 85 Figure 72: Remote Management 85 Figure 73: Parental Control Settings 86 Figure 74: Add or Modify Parental Control Entry 88 Figure 75: Parental Control Settings 89 Figure 76: Access Control 89 Figure 77: Access Control Rule Management 90 Figure 78: Add or Modity Internet Access Control Entry 91 Figure 79: Host Settings 92 Figure 80: Add or Modify an IP
CONTENTS Figure 104: Restore Factory Default 111 Figure 105: Backup & Restore Configuration 112 Figure 106: Reboot 112 Figure 107: Password 113 Figure 108: System Log 114 Figure 109: Mail Account Settings 115 Figure 110: Statistics 116 Figure 111: TCP/IP 118 Figure 112: Internet Protocol 119 Figure 113: Internet Protocol Properties 120 Figure 114: Setting the IP Address Manually 121 Figure 115: PPPoE Connection Type 122 Figure 116: PPPoE Connection Mode 122 Figure 117: MAC Clone
TABLES Table 1: Key Hardware Features 25 Table 2: LED Behavior 26 – 23 –
1 INTRODUCTION OVERVIEW OF THE ROUTER The Barricade™ SMCWBR14S-N5 150Mbps 4-Port Wireless Broadband Router delivers exceptional range and speed, which can fully meet the needs of Small Office/Home Office (SOHO) networks and users demanding higher network performance. The router integrates a 4-port switch, firewall, NAT router, and wireless access point (AP). INCREDIBLE SPEED The SMCWBR14S-N5 provides up to 150 Mbps wireless connections with other 802.
CHAPTER 1 | Introduction Main Features MAIN FEATURES ◆ IEEE 802.11n wireless technology provides a wireless data rate of up to 150 Mbps. ◆ One 10/100 Mbps Auto-Negotiation RJ-45 WAN port, four 10/100 Mbps Auto-Negotiation RJ-45 LAN ports, supporting Auto MDI/MDIX. ◆ Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security. ◆ Shares data and Internet access for users, supporting dynamic IP/static IP/PPPoE Internet access. ◆ Supports Virtual Server, Forwarding, and DMZ host.
CHAPTER 1 | Introduction Package Contents PACKAGE CONTENTS The following items should be found in your package: ◆ SMCWBR14S-N5 150Mbps 4-Port Wireless Broadband Router, ◆ AC Power Adapter ◆ Quick Installation Guide ◆ Resource CD, including: ◆ This Guide ◆ Other Helpful Information NOTE: Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor.
CHAPTER 1 | Introduction Rear Panel Table 2: LED Behavior (Continued) LED Status Description WAN LAN (1-4) On There is a device linked to the corresponding port, but there is no activity. Blinking There is an active device linked to the corresponding port. Off There is no device linked to the corresponding port. On A wireless device has been successfully added to the network by WPS. The LED will remain on for about 5 minutes.
CHAPTER 1 | Introduction Rear Panel ETHERNET WAN PORT This WAN port is where you connect the DSL/cable Modem. ETHERNET LAN LAN1,2,3,4: These ports (1, 2, 3, 4) connect the Router to local PCs.
2 CONNECTING THE ROUTER SYSTEM REQUIREMENTS You must meet the following minimum requirements: ◆ Broadband Internet Access Service (DSL/Cable/Ethernet) ◆ One DSL/Cable Modem that has an RJ-45 connector. ◆ PCs with working Ethernet adapters and Ethernet cables with RJ-45 connectors. ◆ TCP/IP protocol on each PC. ◆ Web browser, such as Microsoft Internet Explorer, Mozilla Firefox, or Apple Safari.
CHAPTER 2 | Connecting the Router Connecting the Router 2. Locate an optimum location for the Router. The best place is usually at the center of your network. The place must meet the Installation Environment Requirements. 3. Adjust the direction of the antennas. Normally, upright is the best direction. 4. Connect PCs and any switch in your LAN to the LAN Ports on the Router, as shown in Figure 3. 5. Connect the DSL/Cable Modem to the WAN port on the Router, as shown in Figure 3. 6.
CHAPTER 2 | Connecting the Router Connecting the Router Figure 4: Client Router Mode Noteboook WISP Signal – 31 – PC
3 QUICK INSTALLATION GUIDE This chapter shows you how to quickly configure the basic functions of your Router using the Quick Setup Wizard. TCP/IP CONFIGURATION The default IP address of the Router is 192.168.2.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, all the default values are used for descriptions. Connect local PCs to the LAN ports of the Router. And then you can configure the IP address for your PC in the following two ways.
CHAPTER 3 | Quick Installation Guide TCP/IP Configuration Figure 5: Success Result of a Ping Command If the result displayed is similar to Figure 6, it means the connection between your PC and the Router has failed. Figure 6: Failure of a Ping Command Follow these steps to check the connection: 1. Is the connection between your PC and the Router correct? The LAN port LED on the Router and the LED on your PC's adapter should be on. 2.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide If the Router's IP address is 192.168.2.1, your PC's IP address must be within the range of 192.168.2.2 ~ 192.168.2.254. QUICK INSTALLATION GUIDE Using the Web-based utility, it is easy to configure and manage the Router. The Web-based utility can be used on any Windows, Macintosh, or UNIX system with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox, or Apple Safari. 1.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide Figure 9: Quick Setup 3. After successfully logging in, click “Quick Setup” to quickly configure your Router. Select Wireless Router mode for an Internet connection through a DSL/cable modem connected to the WAN port. Select Wireless Client Router mode for an Internet connection through a wireless service provider. Figure 10: Operation Mode 4. Click Next. The WAN Connection Type page will appear, as shown in Figure 11.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide Figure 12: Quick Setup – PPPoE ● User Name and Password — Enter the User Name and Password provided by your ISP. These fields are case sensitive. If you have difficulty with this process, contact your ISP. b. If the connection type detected is Dynamic IP, the screen shown in Figure 14 will display. You can then continue with the wireless configuration. c.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide Figure 14: Quick Setup – Wireless ■ Wireless Radio - Enable or disable the wireless radio choosing from the pull-down list. ■ SSID - Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set to “SMC”. This value is casesensitive. For example, “TEST” is NOT the same as “test”.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide the Router without encryption. It is recommended strongly that you choose one of following options to enable security. ■ WPA-PSK/WPA2-PSK - Select WPA based on pre-shared passphrase. ● PSK Password - You can enter ASCII or Hexadecimal characters. For ASCII, the key can be made up of any numbers 0 to 9 and any letters A to Z, the length should be between 8 and 63 characters.
CHAPTER 3 | Quick Installation Guide Quick Installation Guide Figure 16: Quick Setup - Finish – 39 –
4 CONFIGURING THE ROUTER This chapter shows each Web page's key functions and the configuration method. LOGIN After successful login, you see the main menu on the left of the Web page. On the right, there are the corresponding explanations and instructions. Figure 17: The Main Menu The detailed explanations for each Web page’s key functions are listed below.
CHAPTER 4 | Configuring the Router Status STATUS The Status page provides the current status information about the Router. All information is read-only.
CHAPTER 4 | Configuring the Router Quick Setup QUICK SETUP Refer to “Quick Installation Guide” on page 32. WPS This section shows how to quickly add a new wireless device to an existing network using WPS (Wi-Fi Protected Setup). 1. Select WPS from the menu. You will see the next screen, as shown in Figure 19. Figure 19: WPS (Wi-Fi Protected Setup) ■ WPS Status - Enable or disable the WPS function here. ■ Current PIN - The current value of the Router's PIN is displayed here.
CHAPTER 4 | Configuring the Router WPS For the configuration of a new device, this example uses an SMC Wireless Adapter. BY PBC If the wireless adapter supports Wi-Fi Protected Setup and the Push Button Configuration (PBC) method, you can add it to the network by PBC with the following two methods. Method One: 1. Enable the WPS function from Web management page. 2. Press the WPS button on the front panel of the Router. Figure 20: Front Panel 3.
CHAPTER 4 | Configuring the Router WPS Figure 22: WPS-Wireless Configuration Completed Method Two: 1. Enable the WPS function from Web management page. 2. Press the WPS button on the front panel of the Router. Figure 23: Front Panel 3. For the configuration of the wireless adapter, select “Push the button on my access point” in the WPS configuration, as below, and click Next.
CHAPTER 4 | Configuring the Router WPS Figure 24: WPS-Push the button on my access point 4. Wait until the next screen appears. Click Finish to complete the WPS configuration. Figure 25: WPS-Wireless Configuration Completed Method Three: 1. Keep the default WPS Status as Enabled and click the “Add device” button in Figure 26, then the following screen will appear.
CHAPTER 4 | Configuring the Router WPS Figure 26: Add A New Device 2. Select “Press the button of the new device in two minutes” and click Connect. 3. For the configuration of the wireless adapter, select “Push the button on my access point” in the WPS configuration utility, as below, and click Next. Figure 27: WPS-Push the button on my access point 4. Wait until the next screen appears. Click Finish to complete the WPS configuration.
CHAPTER 4 | Configuring the Router WPS Figure 28: WPS-Wireless Configuration Completed BY PIN If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods. Method One: Enter the PIN into my Router. 1. Keep the default WPS Status as Enabled and click the “Add device” button in Figure 29, then the following screen will appear. Figure 29: Add Device 2.
CHAPTER 4 | Configuring the Router WPS 3. For the configuration of the wireless adapter, selected “Enter a PIN into my access point or a registrar” in the WPS configuration, as below, and click Next. Figure 30: WPS-Enter a PIN into my access point NOTE: In this example, the default PIN code of the adapter is 16952898, as shown in the above figure. Method Two: Enter the PIN from my Router. 1. Read the Current PIN code of the Router in Figure 26 (each Router has its unique PIN code.
CHAPTER 4 | Configuring the Router Operation Mode Figure 31: WPS-Enter a PIN from my access point NOTE: The default PIN code of the Router can be found on its label, or in the WPS configuration screen, as shown in Figure 26. Then the new device successfully connected to the network. NOTE: The WPS LED on the Router will turn on green for five minutes when a device has been successfully added to the network. NOTE: The WPS function cannot be configured if the wireless function of the Router is disabled.
CHAPTER 4 | Configuring the Router Network ◆ Wireless Router - In this mode, the device enables multiple users to share a single Internet connection through a DSL/cable modem. All wireless client users share the same Internet connection through the Ethernet WAN port as LAN port users. ◆ Wireless Client Router - In this mode, the device enables multiple users to share a single Internet connection from a wireless Internet service provider (WISP).
CHAPTER 4 | Configuring the Router Network NOTE: If you change the IP Address of LAN, you must use the new IP Address to login the Router. NOTE: If the new LAN IP Address you set is not in the same subnet, the IP Address pool of the DHCP server will change accordingly at the same time, while the Virtual Server and DMZ Host will not take effect until they are reconfigured. WAN Select “Network>WAN”, you can configure the IP parameters of the WAN on the screen below. 1.
CHAPTER 4 | Configuring the Router Network ◆ Use These DNS Servers - If your ISP gives you one or two DNS addresses, select Use These DNS Servers and enter the primary and secondary addresses into the correct fields. Otherwise, the DNS servers will be assigned dynamically from your ISP. NOTE: If you find an error when you go to a Web site after entering the DNS addresses, it is likely that your DNS servers are set up improperly. You should contact your ISP to check the DNS server addresses.
CHAPTER 4 | Configuring the Router Network ◆ Primary/Secondary DNS - (Optional) Enter one or two DNS addresses in dotted-decimal notation provided by your ISP. Click the Save button to save your settings. 3. If your ISP provides a PPPoE connection, select PPPoE option. And you should enter the following parameters (Figure 37): Figure 37: WAN-PPPoE ◆ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive.
CHAPTER 4 | Configuring the Router Network ◆ Connect on Demand - In this mode, the Internet connection can be terminated automatically after a specified inactivity period (Max Idle Time) and be re-established when you attempt to access the Internet again. If you want your Internet connection keeps active all the time, please enter “0” in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects.
CHAPTER 4 | Configuring the Router Network Figure 38: WAN-PPPoE Advanced Settings ◆ MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. ◆ Service Name/AC Name - The service name and AC (Access Concentrator) name, which should not be configured unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work.
CHAPTER 4 | Configuring the Router Network Figure 39: WAN-L2TP ◆ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ◆ Dynamic IP/ Static IP - Choose either as you are given by your ISP. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. ◆ Connect on Demand - You can configure the Router to disconnect from your Internet connection after a specified period of inactivity (Max Idle Time).
CHAPTER 4 | Configuring the Router Network ◆ Connect Manually - You can configure the Router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the Router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. To use this option, click the radio button.
CHAPTER 4 | Configuring the Router Network ◆ Dynamic IP/ Static IP - Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name. If you choose static IP and enter the domain name, you should also enter the DNS assigned by your ISP. And click the Save button. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately.
CHAPTER 4 | Configuring the Router Wireless The Router can not detect PPTP/L2TP/BigPond connections with your ISP. If your ISP uses one of these protocols, then you must configure your connection manually. MAC CLONE Choose menu “Network->MAC Clone”, you can configure the MAC (ROUTER MODE ONLY) address of the WAN on the screen below, Figure 41: Figure 41: MAC Address Clone Some ISPs require that you register the MAC Address of your adapter. Changes are rarely needed here.
CHAPTER 4 | Configuring the Router Wireless Figure 42: Wireless Menu WIRELESS SETTINGS Choose menu Wireless -> Wireless Setting; you can configure the basic (ROUTER MODE) settings for the wireless network on this page. The wireless settings section displays configuration settings for the access point functionality of the Wireless AP/router. It includes the following sections: Figure 43: Wireless Settings (Router Mode) ◆ SSID - Enter a value of up to 32 characters.
CHAPTER 4 | Configuring the Router Wireless other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. When you select your local region from the pull-down list, click the Save button, then the Note Dialog appears. Click OK. Figure 44: Note Dialog NOTE: Limited by local law regulations, the version for North America does not have a region selection option.
CHAPTER 4 | Configuring the Router Wireless ◆ Max Tx Rate - You can limit the maximum transmit rate of the Router through this field. ◆ Enable Wireless Router Radio - The wireless radio of this Router can be enabled or disabled to allow wireless stations access. ◆ Enable SSID Broadcast - When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Router.
CHAPTER 4 | Configuring the Router Wireless Figure 46: Wireless Settings (Client Router Mode) ◆ SSID - The SSID of the AP your Router is going to connect to as a client. You can also use the survey function to select the SSID to join. ◆ BSSID - The BSSID of the AP your Router is going to connect to as a client. You can also use the survey function to select the BSSID to join. ◆ Survey - Click the Survey button to search the AP which runs in the current channel.
CHAPTER 4 | Configuring the Router Wireless ◆ SSID - Enter a value of up to 32 characters. The same SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be “SMC”. This value is casesensitive. For example, “TEST” is NOT the same as “test”. ◆ Enable Wireless Router Radio - The wireless radio of this Router can be enabled or disabled to allow wireless stations access.
CHAPTER 4 | Configuring the Router Wireless Figure 47: Wireless Security ◆ Disable Security - If you do not want to use wireless security, select this check box. However, it is strongly recommended to choose one of the following modes to enable security. ◆ WEP - This security is based on the IEEE 802.11 standard. If you select this check box, you will find a notice in red, as shown in Figure 48.
CHAPTER 4 | Configuring the Router Wireless ■ Type - you can choose the type for the WEP security on the pulldown list. The default setting is Automatic, which can select Open System or Shared-Key authentication type automatically based on the wireless station's capability and request. ■ WEP Key Format - Hexadecimal and ASCII formats are provided. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length.
CHAPTER 4 | Configuring the Router Wireless Figure 49: WPA/WPA2 ◆ ■ Radius Server IP - Enter the IP address of the RADIUS Server. ■ Radius Port - Enter the port that the RADIUS service uses. ■ Radius Password - Enter the password for the RADIUS server. ■ Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. WPA-PSK/WPA2-PSK - The WPA/WPA2 authentication type based on a pre-shared passphrase.
CHAPTER 4 | Configuring the Router Wireless ■ Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. Be sure to click the Save button to save your settings on this page. WIRELESS MAC Choose Wireless -> MAC Filtering from the menu; you can then control FILTERING wireless access by configuring the Wireless MAC Address Filtering function, as shown in Figure 51.
CHAPTER 4 | Configuring the Router Wireless Figure 52: Add or Modify Wireless MAC Address Filtering Entry To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0A-EB-00-07-8A. 2. Provide a simple description of the wireless station in the Description field. For example: Wireless station A. 3.
CHAPTER 4 | Configuring the Router Wireless 3. Delete all or disable all entries if there are any entries already. 4. Click the Add New button. a. Enter the MAC address 00-0A-EB-00-07-8A /00-0A-EB-00-23-11 in the MAC Address field. b. Enter wireless station A/B in the Description field. c. Select Enabled in the Status pull-down list. d. Click the Save Button. e. Click the Back button.
CHAPTER 4 | Configuring the Router Wireless ◆ Transmit Power - Here you can specify the transmit power of the Router. You can select High, Middle, or Low. High is the default setting and is recommended. ◆ Beacon Interval - Enter a value between 20-1000 milliseconds for the Beacon Interval. The beacons are packets sent by the router to synchronize a wireless network. The Beacon Interval value determines the time interval of beacons. The default value is 100.
CHAPTER 4 | Configuring the Router DHCP WIRELESS STATISTICS Select Wireless -> Wireless Statistics from the menu; you can see the MAC Address, Current Status, Received Packets, and Sent Packets for each connected wireless station. Figure 55: Wireless Statistics ◆ MAC Address - The connected wireless station's MAC address. ◆ Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN / Disconnected.
CHAPTER 4 | Configuring the Router DHCP DHCP SETTINGS Select DHCP -> DHCP Settings from the menu. You can configure the DHCP Server on the page, as shown in Figure 57. The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PCs that are connected to the Router on the LAN. Figure 57: DHCP Settings ◆ DHCP Server - Enable or Disable the DHCP server.
CHAPTER 4 | Configuring the Router DHCP NOTE: To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically" mode. DHCP CLIENTS LIST Select DHCP -> DHCP Clients List from the menu; you can view the information about the clients attached to the Router in the next screen (shown in Figure 58). Figure 58: DHCP Clients List ◆ ID - The index of the DHCP Client. ◆ Client Name - The name of the DHCP client.
CHAPTER 4 | Configuring the Router DHCP Figure 59: Address Reservation ◆ MAC Address - The MAC address of the PC for which you want to reserve an IP address. ◆ Assigned IP Address - The reserved IP address for the PC. ◆ Status - The status of this entry either Enabled or Disabled. To Reserve IP addresses: 1. Click the “Add New” button (as shown in Figure 60). 2. Enter the MAC address (in XX-XX-XX-XX-XX-XX format.) and IP address in dotted-decimal notation of the computer you wish to add. 3.
CHAPTER 4 | Configuring the Router Forwarding 5. Click the Delete All button to delete all entries. 6. Click the Next button to go to the next page and click the Previous button to return the previous page. FORWARDING There are four submenus under the Forwarding Application menu (shown in Figure 61): Virtual Servers, Port Triggering, DMZ, and UPnP. Click any of them and you will be able to configure the corresponding function.
CHAPTER 4 | Configuring the Router Forwarding ◆ Status - The status of this entry either Enabled or Disabled. To setup a virtual server entry: 1. Click the Add New… button. (Figure 63) 2. Select the service you want to use from the Common Service Port list. If the Common Service Port list does not have the service that you want to use, type the number of the service port or service port range in the Service Port box. 3. Type the IP Address of the computer in the IP Address box. 4.
CHAPTER 4 | Configuring the Router Forwarding 6. Click the Next button to go to the next page and click the Previous button to return the previous page. NOTE: If you set the service port of the virtual server as 80, you must set the Web management port on “Security –> Remote Management” page to be any other value except 80, such as 8080. Otherwise there will be a conflict, which will disable the virtual server.
CHAPTER 4 | Configuring the Router Forwarding ◆ Incoming Ports Range - The port or port range used by the remote system when it responds to the outgoing request. A response using one of these ports will be forwarded to the PC that triggered this rule. You can input at most 5 groups of ports (or port section). Every group of ports must be set apart with ",". For example, 2000-2038, 2050-2051, 2085, 3010-3030.
CHAPTER 4 | Configuring the Router Forwarding 2. Modify the information. 3. Click the Save button. 4. Click the Enable All button to make all entries enabled 5. Click the Disabled All button to make all entries disabled. 6. Click the Delete All button to delete all entries NOTE: When the trigger connection is released, the according opening ports will be closed. NOTE: Each rule allowed to be used only by one host on LAN synchronously. The trigger connection of other hosts on LAN will be refused.
CHAPTER 4 | Configuring the Router Forwarding UPNP Select Forwarding -> UPnP from the menu; you can view the information about UPnP (Universal Plug and Play) in the screen (shown in Figure 67). The UPnP feature allows devices, such as Internet computers, to access the local host resources or devices as needed. UPnP devices can be automatically discovered by the UPnP service application on the LAN.
CHAPTER 4 | Configuring the Router Security SECURITY There are four submenus under the Security menu as shown in Figure 88: Basic Security, Advanced Security, Local Management and Remote Management. Click any of them, and you will be able to configure the corresponding function. Figure 68: The Security Menu BASIC SECURITY Select Security -> Basic Security from the menu; you can configure the basic security in the screen as shown in Figure 69.
CHAPTER 4 | Configuring the Router Security ■ ◆ IPSec Passthrough - Internet Protocol Security (IPSec) is a suite of protocols for ensuring private, secure communications over Internet Protocol (IP) networks, through the use of cryptographic security services. To allow IPSec tunnels to pass through the Router, keep the default, Enabled.
CHAPTER 4 | Configuring the Router Security ◆ Packets Statistics Interval (5~60) - The default value is 10. Select a value between 5 and 60 seconds from the drop-down list. The Packets Statistics Interval value indicates the time section of the packets statistics. The result of the statistics is used for analysis by SYN Flood, UDP Flood and ICMP-Flood. ◆ DoS Protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS protection function.
CHAPTER 4 | Configuring the Router Security LOCAL MANAGEMENT Select Security->Local Management from the menu; you can configure the management rules in the screen, as shown in Figure 71. The management feature allows you to deny computers in the LAN from accessing the Router. Figure 71: Local Management By default, the radio button “All the PCs on the LAN are allowed to access the Router's Web-Based Utility” is checked.
CHAPTER 4 | Configuring the Router Parental Control ◆ Web Management Port - Web browser access normally uses the standard HTTP service port 80. This Router's default remote management web port number is 80. For greater security, you can change the remote management web port to a custom port by entering that number in the box provided. Choose a number between 1 and 65534, but do not use the number of any common service port.
CHAPTER 4 | Configuring the Router Parental Control ◆ Parental Control - Check Enable if you want this function to take effect, otherwise check Disable. ◆ MAC Address of Parental PC - In this field, enter the MAC address of the controlling PC, or you can make use of the “Copy To Above” button below. ◆ MAC Address of Your PC - This field displays the MAC address of the PC that is managing this Router.
CHAPTER 4 | Configuring the Router Parental Control Figure 74: Add or Modify Parental Control Entry For example: If you desire that the child PC with MAC address 00-11-2233-44-AA can access www.google.com on Saturday only while the parent PC with MAC address 00-11-22-33-44-BB is without any restriction, you should follow the settings below. 1. Click Parental Control on the menu to enter the Parental Control Settings page.
CHAPTER 4 | Configuring the Router Access Control 4. Click Save to complete the settings. Then you will go back to the Parental Control Settings page and see the following list, as shown in Figure 75. Figure 75: Parental Control Settings ACCESS CONTROL There are four submenus under the Access Control menu as shown in Figure 76: Rule, Host, Target, and Schedule. Click any of them, and you will be able to configure the corresponding function.
CHAPTER 4 | Configuring the Router Access Control Figure 77: Access Control Rule Management ◆ Enable Internet Access Control - Select the check box to enable the Internet Access Control function, so the Default Filter Policy can take effect. ◆ Rule Name - Here displays the name of the rule and this name is unique. ◆ Host - Here displays the host selected in the corresponding rule. ◆ Target - Here displays the target selected in the corresponding rule.
CHAPTER 4 | Configuring the Router Access Control 3. Select a host from the Host drop-down list or choose “Click Here To Add New Host List”. 4. Select a target from the Target drop-sown list or choose “Click Here To Add New Target List”. 5. Select a schedule from the Schedule drop-down list or choose “Click Here To Add New Schedule”. 6. In the Action field, select Deny or Allow. 7. In the Status field, select Enabled or Disabled to enable or disable your entry. Click the Save button.
CHAPTER 4 | Configuring the Router Access Control 2. Click “Access Control->Target” in the left to enter the Target Settings page. Add a new entry with the Target Description is Target_1 and Domain Name is www.google.com. 3. Click “Access Control->Schedule” in the left to enter the Schedule Settings page. Add a new entry with the Schedule Description is Schedule_1, Day is Sat and Sun, Start Time is 1800 and Stop Time is 2000. 4.
CHAPTER 4 | Configuring the Router Access Control ◆ Information - Displays the information about the host. It can be IP or MAC. ◆ Modify - To modify or delete an existing entry. To add a new entry, please follow the steps below. 1. Click the “Add New” button. 2. In the Mode field, select IP Address or MAC Address. ■ ■ If you select IP Address, the screen in Figure 80 is displayed. ● In the Host Description field, create a unique description for the host (e.g. Host_1).
CHAPTER 4 | Configuring the Router Access Control For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA, you should first follow the settings below: 1. Click “Add New” button in Figure 79 to enter the “Add or Modify a Host Entry” page. 2. In Mode field, select MAC Address from the drop-down list. 3. In Host Description field, create a unique description for the host (e.g. Host_1). 4. In MAC Address field, enter 00-11-22-33-44-AA. 5.
CHAPTER 4 | Configuring the Router Access Control ● In IP Address field, enter the IP address of the target. ● Select a common service from Common Service Port drop-down list, so that the Target Port will be automatically filled. If the Common Service Port drop-down list doesn’t have the service you want, specify the Target Port manually. ● In Protocol field, select TCP, UDP, ICMP or ALL. b. If you select Domain Name, the screen in Figure 84 is shown.
CHAPTER 4 | Configuring the Router Access Control Figure 84: Add or Modify a Domain Name Access Target Entry For example: If you desire to restrict the internet activities of a host with MAC address 00-11-22-33-44-AA in the LAN to access www.google.com only, you should first follow the settings below: 1. Click the “Add New” button in Figure 82 to enter the Add or Modify an Access Target Entry page. 2. In Mode field, select Domain Name from the drop-down list. 3.
CHAPTER 4 | Configuring the Router Access Control SCHEDULE Select Access Control -> Schedule from the menu; you can view and set a schedule list in the next screen, as shown in Figure 86. The schedule list is necessary for Access Control Rules. Figure 86: Schedule Settings ◆ Schedule Description - Here displays the description of the schedule and this description is unique. ◆ Day - Here displays the day(s) in a week. ◆ Time - Here displays the time period in a day.
CHAPTER 4 | Configuring the Router Access Control Figure 87: Advanced Schedule Settings For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA to access www.google.com only from 18:00 to 20:00 on Saturday and Sunday, you should first follow the settings below: 1. Click the “Add New” button shown in Figure 87 to enter the Advanced Schedule Settings page. 2. In Schedule Description field, create a unique description for the schedule (e.g. Schedule_1). 3.
CHAPTER 4 | Configuring the Router Advanced Routing ADVANCED ROUTING Select static routing list from the menu; you can configure the static route in the next screen (Figure 88). A static route is a pre-determined path that network information must travel to reach a specific host or network. Figure 88: Static Routing To add static routing entries: 1. Click Add New. Figure 89: Add or Modify a Static Route Entry 2.
CHAPTER 4 | Configuring the Router Bandwidth Control Other configurations for the entries: Click the Delete button to delete the entry. Click the Enable All button to enable all the entries. Click the Disable All button to disable all the entries. Click the Delete All button to delete all the entries. Click the Previous button to view the information in the previous screen. Click the Next button to view the information in the next screen.
CHAPTER 4 | Configuring the Router IP & MAC Binding Click Enable to enable this entry. Click the Clear button to clear a single entry. Click the Clear All button to clear all entries. Click the Save button to save all configurations. NOTE: 1. The conversion relation of bandwidth: 1Mbps = 1000Kbps. 2. Please choose the Network Connection Type and set the bandwidth according to your Network. If you are not clear about that, please contact with your ISP for help. 3.
CHAPTER 4 | Configuring the Router IP & MAC Binding BINDING SETTING This page displays the IP & MAC Binding Setting table; you can configure it as needed (as shown in Figure 92). Figure 92: Binding Setting ◆ MAC Address - The MAC address of the controlled computer in the LAN. ◆ IP Address - The assigned IP address of the controlled computer in the LAN. ◆ Bind - Check this option to enable ARP binding for a specific device. ◆ Modify - To modify or delete an existing entry.
CHAPTER 4 | Configuring the Router IP & MAC Binding To modify or delete an existing entry, follow the steps below. 1. Find the desired entry in the table. 2. Click Modify or Delete in the Modify column. To find an existing entry, follow the steps below. 1. Click the Find button as shown in Figure 94. 2. Enter the MAC Address or IP Address. 3. Click the Find button in the page as shown in Figure 94. Figure 94: Find IP & MAC Binding Entry Click the “Enable All” button to make all entries enabled.
CHAPTER 4 | Configuring the Router DDNS ◆ IP Address - The assigned IP address of the controlled computer in the LAN. ◆ Status - Indicates whether or not the MAC and IP addresses are bound. ◆ Configure - Load or delete an item. ● l Load - Load the item to the IP & MAC Binding list. ● l Delete - Delete the item. Click the Bind All button to bind all the current items, available after enable. Click the Load All button to load all items to the IP & MAC Binding list.
CHAPTER 4 | Configuring the Router DDNS Figure 96: Dyndns.org DDNS Settings To set up for DDNS, follow these instructions: 1. Type the Domain Name received from your DDNS service provider. 2. Type the User Name for your DDNS account. 3. Type the Password for your DDNS account. 4. Click the Login button to log in to the DDNS service. ◆ Connection Status -The status of the DDNS service connection is displayed here. NO-IP.COM DDNS If the DDNS Service Provider you select is www.no-ip.
CHAPTER 4 | Configuring the Router DDNS ◆ Connection Status - The status of the DDNS service connection is displayed here. ◆ Click Logout to log out the DDNS service. To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from DDNS service provider. Click the Login button to log in the DDNS service. COMEXE.CN DDNS If the DDNS Service Provider you select is www.comexe.
CHAPTER 4 | Configuring the Router System Tools 3. Type the Domain Name you received from DDNS service provider. Click the Login button to log in the DDNS service. SYSTEM TOOLS Select System Tools, and you can see the submenus under the main menu: Time Settings, Diagnostic, Firmware Upgrade, Factory Defaults, Backup & Restore, Reboot, Password, System Log and Statistics. Click any of them, and you will be able to configure the corresponding function.
CHAPTER 4 | Configuring the Router System Tools ◆ NTP Server Prior - Enter the address for the NTP Server, then the Router will get the time from the NTP Server preferentially. In addition, the Router includes some common NTP Servers, so it can get the time automatically once it connects the Internet. To configure the system manually: 1. Select your local time zone. 2. Enter date and time in the right blanks. 3. Click Save to save the configuration. To configure the system automatically: 1.
CHAPTER 4 | Configuring the Router System Tools DIAGNOSTIC Select System Tools->Diagnostic from the menu; you can use Ping or Traceroute functions to check connectivity of your network in the following screen. Figure 101: Diagnostic Tools ◆ Diagnostic Tool - Check the radio button to select one diagnostic too. ■ Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway.
CHAPTER 4 | Configuring the Router System Tools ◆ Traceroute Max TTL - The max number of hops for a Traceroute connection. Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 102: Diagnostic Results NOTE: Only one user can use this tool at one time. Options “Number of Pings”, “Ping Size” and “Ping Timeout” are used for the Ping function.
CHAPTER 4 | Configuring the Router System Tools To upgrade the Router's firmware, follow the instructions below: 1. Download a more recent firmware upgrade file from the SMC website (http://www.smc.com). 2. Type the path and file name of the update file into the File field. Or click the Browse button to locate the update file. 3. Click the Upgrade button. NOTE: New firmware versions are posted at http://www.smc.com and can be downloaded for free.
CHAPTER 4 | Configuring the Router System Tools NOTE: Any settings you have saved will be lost when the default settings are restored. NOTE: When press and hold the WPS Button for more than 5 seconds, you will reset the router. BACKUP & RESTORE Select System Tools-> Backup & Restore from the menu; you can save the current configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 105.
CHAPTER 4 | Configuring the Router System Tools Some settings of the Router will take effect only after rebooting, which include ◆ Change of the LAN IP Address (system will reboot automatically). ◆ Change of DHCP Settings. ◆ Change of Wireless configurations. ◆ Change of the Web Management Port. ◆ Upgrade of the Router firmware (system will reboot automatically). ◆ Restore the Router's settings to factory defaults (system will reboot automatically).
CHAPTER 4 | Configuring the Router System Tools SYSTEM LOG Selct System Tools->System Log from the menu; you can view the logs of the Router. Figure 108: System Log ◆ Auto Mail Feature - Indicates whether auto mail feature is enabled or not. ◆ Mail Settings - Set the receiving and sending mailbox address, server address, validation information as well as the timetable for Auto Mail Feature, as shown in Figure 109. ◆ Log Type - By selecting the log type, only logs of this type will be shown.
CHAPTER 4 | Configuring the Router System Tools Figure 109: Mail Account Settings ◆ From - Your mail box address. The Router would connect it to send logs. ◆ To - Recipient’s address. The destination mailbox where the logs would be received. ◆ SMTP Server - Your smtp server. It corresponds with the mailbox filled in the From field. You can log on the relevant website for Help if you are not clear with the address. ◆ Authentication - Most SMTP Server requires Authentication.
CHAPTER 4 | Configuring the Router System Tools Click the Next button to go to the next page, or click the Previous button return to the previous page. STATISTICS Select System Tools->Statistics from the menu; you can view the statistics of the Router, including total traffic and current traffic of the last Packets Statistic Interval. Figure 110: Statistics ◆ Current Statistics Status - Enable or Disable. The default value is disabled. To enable, click the Enable button.
CHAPTER 4 | Configuring the Router System Tools Current Packets - The total amount of packets received and transmitted in the last Packets Statistic interval seconds. Current Bytes - The total amount of bytes received and transmitted in the last Packets Statistic interval seconds. Current ICMP Tx - The total amount of the ICMP packets transmitted to WAN in the last Packets Statistic interval seconds.
A CONFIGURING THE PC The section shows how to install and configure TCP/IP settings correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if needed. INSTALL TCP/IP COMPONENTS 1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel. 2. Click the Network and Internet Connections icon, and then click on the Network Connections tab in the following window. 3.
APPENDIX A | Configuring the PC Install TCP/IP Components Figure 112: Internet Protocol 5. The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. Now you have two ways to configure the TCP/IP protocol below: a. Set the IP address automatically.
APPENDIX A | Configuring the PC Install TCP/IP Components Figure 113: Internet Protocol Properties b. Set the IP address manually. Select “Use the following IP address” radio button and enter the following items: — If the Router's LAN IP address is 192.168.2.1, type an IP address such as 192.168.2.x (where x is from 2 to 254), and Subnet mask as 255.255.255.0. — Type the Router’s LAN IP address (the default IP is 192.168.2.1) into the Default gateway field.
APPENDIX A | Configuring the PC Install TCP/IP Components Figure 114: Setting the IP Address Manually 2 2 6. Click OK to keep your settings.
B FAQ HOW DO I CONFIGURE THE ROUTER FOR INTERNET ACCESS BY ADSL USERS? 1. Configure the ADSL Modem in RFC1483 bridge mode. 2. Connect Ethernet cable from the ADSL Modem to the WAN port on the Router. The telephone cord plugs into the Line port of the ADSL Modem. 3. Log in to the Router, click “Network” on the web page menu and then click “WAN” on the submenu. a. On the WAN page, select “PPPoE” for the WAN connection type. b.
APPENDIX B | FAQ How do I configure the Router for Internet access by Ethernet users? NOTE: Sometimes the connection cannot be disconnected although you have specified a Max Idle Time, since some applications may be visiting the Internet continually in the background. NOTE: If you are a Cable user, configure the Router following the above steps. HOW DO I CONFIGURE THE ROUTER FOR INTERNET ACCESS BY ETHERNET USERS? 1.
APPENDIX B | FAQ I want to use Netmeeting, what do I need to do? I WANT TO USE NETMEETING, WHAT DO I NEED TO DO? 1. If you start Netmeeting as a host, you do not need to change anything on the Router. 2. If you start as a response, you need to configure a Virtual Server or DMZ Host, and make sure the H323 ALG is enabled. 3. Configure a Virtual Server: a. Log in to the Router, click “Forwarding” on the menu, and then click "Virtual Servers" on the submenu. b.
APPENDIX B | FAQ I want to use Netmeeting, what do I need to do? NOTE: The other party should call your WAN IP, which is displayed on the “Status” page. 4. Enable a DMZ Host: a. Log in to the Router, click “Forwarding” on the menu, and then click “DMZ” on the submenu. b. On the "DMZ" page, click the Enable radio button. c. Type your IP address into the “DMZ Host IP Address” field (for example, 192.168.2.169). d. Click the Save button. Figure 120: DMZ 5. Enable the H323 ALG: a.
APPENDIX B | FAQ I want to build a WEB Server on the LAN, what should I do? Figure 121: Basic Security I WANT TO BUILD A WEB SERVER ON THE LAN, WHAT SHOULD I DO? 1. Change the Web management port number: Because the Web Server port 80 will interfere with the Web management port 80 on the Router, you must change the Web management port number to avoid interference. a. Log in to the Router, click “Security” on the menu, and then click "Remote Management" on the submenu. b.
APPENDIX B | FAQ Wireless stations cannot connect to the Router a. Log in to the Router, click “Forwarding” on the menu, and then click "Virtual Servers" on the submenu. b. On the "Virtual Servers" page, click “Add New”. c. On the “Add or Modify a Virtual Server” page, enter “80” into the field for the “Service Port”. d. Enter your IP address in the “IP Address” field (for example, 192.168.2.188). e. Set to Enable and then Save.
APPENDIX B | FAQ Wireless stations cannot connect to the Router 4. If the wireless connection is ready, but you cannot access the Router, check the IP Address of your wireless station.
C SPECIFICATIONS STANDARDS IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX 802.11b 802.11g 802.
APPENDIX C | Specifications SECURITY WEP/WPA/WPA2/WPA2-PSK/WPA-PSK SENSITIVITY @PER 130 Mbps: -68dBm@10% PER 108 Mbps: -68dBm@10% PER 54 Mbps: -68dBm@10% PER 11 Mbps: -85dBm@8% PER 6 Mbps: -88dBm@10% PER 1 Mbps: -90dBm@8% PER ANTENNA GAIN 5dBi TEMPERATURE Operating: 0 °C to 40 °C (32 to 104 °F) Storage: -40 °C to 70 °C (-40 to 158 °F) HUMIDITY Operating: 10% to 90% (non-condensing) Storge: 5%-90% (non-condensing) – 130 –
GLOSSARY IEEE 802.11B A wireless standard that supports wireless communications in the 2.4 GHz band using Direct Sequence Spread Spectrum (DSSS). The standard provides for data rates of 1, 2, 5.5, and 11 Mbps. IEEE 802.11G A wireless standard that supports wireless communications in the 2.4 GHz band using Orthogonal Frequency Division Multiplexing (OFDM). The standard provides for data rates of 6, 9, 12, 18, 24, 36, 48, 54 Mbps. IEEE 802.11g is also backward compatible with IEEE 802.11b. IEEE 802.
GLOSSARY ISP (INTERNET SERVICE A company that provides access to the Internet. PROVIDER) MTU (MAXIMUM The size in bytes of the largest packet that can be transmitted. TRANSMISSION UNIT) NAT (NETWORK NAT technology translates IP addresses of a local area network to a ADDRESS TRANSLATION) different IP address for the Internet. PPPOE (POINT TO POINT PPPoE is a protocol for connecting remote hosts to the Internet over an PROTOCOL OVER always-on connection by simulating a dial-up connection.
INDEX A K AC power adapter 30 antennas 27 key features 25 L B DDNS 104 default IP 32 diagnostic tools 109 DNS addresses 52 Dynamic IP 35, 53 LAN LED 27 LAN ports 28 LED indicators 26, 27 LEDs LAN 27 Power 26 System 26 WAN 27 WLAN 26 WPS 27 local management 85 location of router 30 logging in, web 34 login page 40 login password 36 logs, system 114 E M basic setup, wizard 42 C channel, operating 37 connections, router 29 contents of package 26 D environment requirements 29 Ethernet port 28 F f
INDEX Power LED 26 PPPoE 35 proxy, web setting 34 Q quick setup 35 R radio channel 37 radio enable 37 region setting,country setting 37 remote management 85 requirements, system 29 router status 41 S setup wizard steps 42 setup, quick 35 SMTP server 115 software upgrade 110 specifications, hardware 129 Static IP 35, 53 statistics 116 status information 41 System LED 26 system logs 114 system requirements 29 T TCP/IP configuration 32 TCP/IP settings 118 temperature, operating 29 U upgrading software 11
Headquarters No. 1, Creation Rd. III Hsinchu Science Park Taiwan 30077 Tel: +886 3 5638888 Fax: +886 3 6686111 (for Asia-Pacific): Technical Support information at www.smc-asia.com www.smcnetworks.co.kr SMCWBR14S-N5,SMCWBR14S-N5 SMCWBR14-N5 www.smc.
