USER GUIDE EZ SwitchTM 10/100/1000 5-Port Gigabit Ethernet PoE Switch SMCGS501P
EZ SwitchTM 10/100/1000 User Guide From SMC’s EZ line of low-cost workgroup LAN solutions No. 1, Creation Road III, Hsinchu Science Park, 30077, Taiwan, R.O.C.
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright © 2014 by SMC Networks, Inc. No.
WARRANTY AND PRODUCT REGISTRATION To register SMC products and to review the detailed warranty statement, please refer to the Support Section of the SMC Website at http://www.smc.com.
COMPLIANCES AND SAFETY STATEMENTS FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
COMPLIANCES AND SAFETY STATEMENTS CE MARK DECLARATION OF CONFORMANCE FOR EMI AND SAFETY (EEC) Declaration of Conformity (DoC) can be obtained from www.smc.com -> support -> download This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/ 68/EEC.
COMPLIANCES AND SAFETY STATEMENTS CLASS A This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.
COMPLIANCES AND SAFETY STATEMENTS ◆ Pay attention to the power load of the outlet or prolonged lines. An overburdened power outlet or damaged cords and plugs may cause electric shock or fire. Check the power cords regularly, if you find any damage, replace it at once. ◆ Proper space for heat dissipation is necessary to avoid any damage caused by device overheating. The ventilation holes on the device are designed for heat dissipation to ensure that the device works normally.
COMPLIANCES AND SAFETY STATEMENTS ◆ Ne placez pas cet appareil à proximité d’un lieu humide ou mouillé. Prenez garde à ne renverser aucun liquide sur cet appareil. ◆ Merci de suivre les instructions du manuel d'utilisateur / guide d’installation rapide attentivement pour connecter l'appareil à votre PC ou à tout autre produit électronique. Toute connexion non valide peut provoquer un problème électrique ou un risque d'incendie. ◆ Ne placez pas cet appareil sur une surface ou un support instable.
COMPLIANCES AND SAFETY STATEMENTS PRECAUCIONES DE SEGURIDAD Lea la siguiente información detenidamente antes de utilizar el dispositivo. Siga las indicaciones de precaución que se mencionan a continuación para proteger el dispositivo contra riesgos y daños causados por el fuego y la energía eléctrica: ◆ Utilice el adaptador de alimentación incluido en el paquete del dispositivo. ◆ Preste atención a la carga de potencia de la toma de corriente o de los alargadores.
COMPLIANCES AND SAFETY STATEMENTS ◆ Respeite a potência da tomada eléctrica e das extensões. Uma tomada eléctrica sobrecarregada ou cabos e fichas danificadas podem causar choques eléctricos ou fogo. Verifique regularmente os cabos de alimentação. Caso algum se encontre danificado, substitua-o imediatamente. ◆ É necessário deixar algum espaço livre em volta do dispositivo para dissipação de calor, de forma a evitar danos causados pelo sobreaquecimento do dispositivo.
ABOUT THIS GUIDE PURPOSE This guide details the hardware features of the switch, including the physical and performance-related characteristics, and how to install the switch. AUDIENCE The guide is intended for use by network administrators who are responsible for installing and setting up network equipment; consequently, it assumes a basic working knowledge of LANs (Local Area Networks).
CONTENTS 1 WARRANTY AND PRODUCT REGISTRATION 4 COMPLIANCES AND SAFETY STATEMENTS 5 ABOUT THIS GUIDE 12 CONTENTS 13 INTRODUCTION 15 Overview 2 15 Features 15 PoE Features 16 HARDWARE DESCRIPTION 17 Front Panel 17 Port and System Status LEDs Rear Panel 3 RJ-45 Ports 18 Power Connector 18 INSTALLING THE SWITCH 19 Package Contents 19 Precautions 19 Safety Requirements 19 Location Requirements 20 Powering On 20 Connecting Network Devices 4 17 18 21 Cabling Guidelines
CONTENTS A Department/Workgroup PoE Switch 22 Power over Ethernet Powered Devices 23 TROUBLESHOOTING 24 Diagnosing Switch Indicators 24 The Power LED is Off 24 The Link/Act LED is Off when a Device is Connected to the Corresponding Port 24 B Power and Cooling Problems 24 Installation 25 SPECIFICATIONS 26 Physical Characteristics 26 – 14 –
1 INTRODUCTION OVERVIEW The EZ Switch 10/100/1000 SMCGS501P PoE switch provides five 10/100/1000 Mbps auto-negotiating RJ-45 ports. Each port on the switch support auto MDI/ MDI-X, which eliminates the need for crossover cables or uplink ports. The switch is plug-and-play; any port can be connected to a server, a hub, or a switch, using straight-through or crossover cable. FEATURES ◆ Complies with IEEE 802.3, IEEE 802.3u, and IEEE 802.
CHAPTER 1 | Introduction Overview POE FEATURES The SMCGS501P can provide up to 30 Watts of power to one attached device, such as a VoIP phone, wireless access point, or surveillance camera, etc, over existing Cat. 5 cable. The switch can deliver up to 15.4/30 Watts on Port 1, which can eliminate the need for an individual power source for the attached device, saving on costs for a power cable and avoiding power outlet availability issues.
2 HARDWARE DESCRIPTION This chapter describes the front panel, rear panel, and LED indicators of the switch. FRONT PANEL The front panel of SMCGS501P consists of switch LED indicators. Figure 1: SMCGS501P Switch Front Panel PORT AND SYSTEM STATUS LEDS This switch includes a display panel for key system and port indications that simplify installation and network troubleshooting. The LEDs, which are located on the front panel, are described in the following table.
CHAPTER 2 | Hardware Description Rear Panel Table 1: System and Port Status LEDs (Continued) LED Condition Status PoE On Green A PoE device is connected. Off No PoE device connected. REAR PANEL Figure 2: SMCGS501P Switch Rear Panel RJ-45 PORTS The switch contains five 1000BASE-TX RJ-45 ports. All ports support automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs.
3 INSTALLING THE SWITCH Before installing the switch, verify that you have all the items listed under “Package Contents.” If any of the items are missing or damaged, contact your local SMC distributor. Also be sure you have all the necessary tools and cabling before installing the switch.
CHAPTER 3 | Installing the Switch Precautions ◆ Use only the AC-DC power adapter and power cord provided with the switch. ◆ Make sure the voltage of the power supply meets the requirement of the input voltage of the switch. ◆ Do not push any objects into the openings of the switch. ◆ Ensure the vent holes are well ventilated and unblocked. ◆ Do not open or remove the cover of the switch.
CHAPTER 3 | Installing the Switch Connecting Network Devices CONNECTING NETWORK DEVICES This switch is designed to be connected to 10, 100 or 1000 Mbps network cards in PCs and servers, as well as to other switches and hubs. CABLING GUIDELINES The RJ-45 ports on the switch support automatic MDI/MDI-X pinout configuration, so you can use standard straight-through twisted-pair cables to connect to any other network device (PCs, servers, switches, routers, or hubs).
4 PRODUCT APPLICATION DEPARTMENT/WORKGROUP POE SWITCH The SMCGS501P is specially designed as part of a Multi-Service Operator (MSO) solution for an IPTV system. The Edge-Core ECS4510-12PD is a PoE PD (powered device) switch that can operate in a cost-effective combination with the SMCGS501P. An SMCGS501P switch can supply 30 Watts of power to an ECS4510-12PD, which itself can provide power to an 802.3af-compliant device, such as an IP camera or wireless access point.
CHAPTER 4 | Product Application Power over Ethernet Powered Devices POWER OVER ETHERNET POWERED DEVICES Table 2: Power over Ethernet Powered Devices Voice over IP phones 3~5 Watts Enterprises can install PoE VoIP phones, ATA and other Ethernet/ non-Ethernet end-devices connected to a central location where an un-interruptible power supply and power control system are installed.
A TROUBLESHOOTING DIAGNOSING SWITCH INDICATORS THE POWER LED IS OFF ◆ Make sure the AC-DC power adapter is connected to the switch and power source properly. ◆ Make sure the power source is ON. THE LINK/ACT LED IS OFF WHEN A DEVICE IS CONNECTED TO THE CORRESPONDING PORT ◆ Make sure that the cable connectors are firmly plugged into the switch and the device. ◆ Make sure the connected device is turned on and working properly. ◆ The cable must be less than 100 meters long (328 feet).
APPENDIX A | Troubleshooting Installation INSTALLATION Verify that all system components have been properly installed. If one or more components appear to be malfunctioning (such as the power cord or network cabling), test them in an alternate environment where you are sure that all the other components are functioning properly.
B SPECIFICATIONS PHYSICAL CHARACTERISTICS STANDARDS IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE802.3ab 1000BASE-T IEEE 802.3X Flow Control FEATURES IEEE 802.3x Flow Control Auto MDI/MDI-X Supports auto-negotiation of speed (10/100/1000 Mbps) and duplex mode (half/ full) Wire-speed packet filtering and forwarding rate Store-and-forward architecture filters fragment & CRC error packets IGMP snooping v1/v2 POE FEATURE Support IEEE 802.3af/802.
APPENDIX B | Specifications Physical Characteristics SWITCHING DATABASE 2K MAC address entries BUFFER MEMORY 2K Bits per device SWITCHING 10 Gbps CAPACITY THROUGHOUT 7.4 Mpps DIMENSIONS 14.0 x 7.7 x 2.7 cm (5.51 x 3.03 x 1.06 in.) WEIGHT 256 g (0.56 lbs) POWER SUPPLY AC Input: 100~240 V, 50/60 Hz DC Output: DC 51 V, 0.
APPENDIX B | Specifications Physical Characteristics IMMUNITY EN55024 IEC61000-4-2/3/4/5/6/8/11 EMISSIONS FCC Class A, EN55022/EN61000-3-2/3 TEMPERATURE Operating: 0 to 50 °C (32 to 122 °F) Storage: -40 to 70 °C (-40 to 158 °F) HUMIDITY Operating: 10% to 90% (non-condensing) Storage: 5% to 90% (non-condensing) – 28 –
Headquarters No. 1, Creation Rd. III Hsinchu Science Park Taiwan 30077 Tel: +886 3 563 8888 Fax: +886 3 668 6111 su www.smc.com www.smc-asis.com www.smcnetworks.co.kr Declaration of Conformity (DoC) can be obtained from www.smc.com -> support -> download SMCGS501P www.smc.com 150200062800A R02 20 Mason • Irvine, CA 92618 • Phn: 949-679-8000 • www.smc.
