EZ Switch 10/100/1000 User Guide From SMC’s EZ line of low-cost workgroup LAN solutions 38 Tesla Irvine, CA 92618 Phone: (949) 679-8000 May 2005 Pub #: 150000018400H R01
Copyright Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright © 2005 by SMC Networks, Inc.
LIMITED WARRANTY Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace any product not operating as warranted with a similar or functionally equivalent product, during the applicable warranty term.
PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.
COMPLIANCES FCC - Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications.
Immunity: • Product family standard according to EN 55024:1998 • Electrostatic Discharge according to EN 61000-4-2:1995 (Contact Discharge: ± 4 kV, Air Discharge: ± 8 kV) • Radio-frequency electromagnetic field according to EN 61000-4-3:1996 (80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m) • Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/DC power supply: ± 1 kV, Data/Signal lines: ± 0.
Please read the following safety information carefully before installing the Switch: WARNING: Installation and removal of the unit must be carried out by qualified personnel only. • This guide is intended for use by network administrators who are responsible for setting up and installing network equipment; consequently it assumes a basic working knowledge of LANs (Local Area Networks). • The unit must be connected to an earthed (grounded) outlet to comply with international safety standards.
France and Peru only This unit cannot be powered from IT† supplies. If your supplies are of IT type, this unit must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the secondary connection point labelled Neutral, connected directly to earth (ground). † Impédance à la terre Power Cord Set U.S.A. and Canada The cord set must be UL-approved and CSA certified. The minimum specifications for the flexible cord are: - No. 18 AWG - not longer than 2 meters, or 16 AWG.
Veuillez lire à fond l'information de la sécurité suivante avant d'installer le Switch: AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être confiés à un personnel qualifié. • Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu'il n'y a pas de connexion de mise à la terre (mise à la masse). • Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de respecter les normes internationales de sécurité.
Cordon électrique - Il doit être agréé dans le pays d’utilisation Etats-Unis et Canada: Le cordon doit avoir reçu l’homologation des UL et un certificat de la CSA. Les spe'cifications minimales pour un cable flexible sont AWG No. 18, ouAWG No. 16 pour un cable de longueur infe'rieure a` 2 me'tres. - type SV ou SJ - 3 conducteurs Le cordon doit être en mesure d’acheminer un courant nominal d’au moins 10 A.
• Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose angeschlossen werden. • Das Gerät muß an eine geerdete Steckdose angeschlossen werden, welche die internationalen Sicherheitsnormen erfüllt. • Der Gerätestecker (der Anschluß an das Gerät, nicht der Wandsteckdosenstecker) muß einen gemäß EN 60320/IEC 320 konfigurierten Geräteeingang haben. • Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein.
Warnings and Cautionary Messages Warning: This product does not contain any user serviceable parts. Warning: Installation and removal of the unit must be carried out by qualified personnel only. Warning: When connecting this device to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent electrical hazards. Warning: This product uses lasers to transmit signals over fiber optic cable.
Environmental Statement The manufacturer of this product endeavours to sustain an environmentally-friendly policy throughout the entire production process. This is achieved though the following means: • Adherence to national legislation and regulations on environmental production standards. • Conservation of operational resources. • Waste reduction and safe disposal of all harmful un-recyclable by-products. • Recycling of all reusable waste content.
Safety Compliance Underwriters Laboratories Compliance Statement Important! Before making connections, make sure you have the correct cord set.
Contents INTRODUCTION Description of Hardware Features and Benefits Front Panel RJ-45 Ports SMCGS5 Front and Rear Panels SMCGS8 Front and Rear Panels Rear Panel INSTALLING THE SWITCH Package Checklist Selecting a Site Instructions APPLICATION EXAMPLE TROUBLESHOOTING SPECIFICATIONS 1 1 1 2 3 4 4 5 5 5 6 8 9 10
EZ Switch 10/100/1000 INTRODUCTION The EZ Switch 10/100/1000, SMCGS5 and SMCGS8, are high-performance Gigabit Ethernet switches designed for delivering Gigabit connectivity to the desktop. It provides 5/8 full-duplex 1000BASE-T ports that significantly improve network performance and boost throughput for high-bandwidth applications. With 10/16 Gigabits of aggregate bandwidth, this switch provides the quickest solution to meeting the growing demands on your network's limited resources.
EZ Switch 10/100/1000 Front Panel LEDs The front panel of the switch provides status LEDs for “at-a-glance” system monitoring. The following table details the functions of the various indicators. Port and System Status LEDs LED Condition Status Power On Power on, normal operation. Off Power off or failure. On(Green) Network device is correctly connected to the switch through this port. Off No link. Flashing (Green) Data is being sent or received through this port.
EZ Switch 10/100/1000 SMCGS8 Front and Rear Panels Rear Panel The DC power socket is located on the rear panel of the switch.
EZ Switch 10/100/1000 INSTALLING THE SWITCH Before installing the switch, verify that you have all the items listed under “Package Contents.” If any of the items are missing or damaged, contact your local SMC distributor. Also be sure you have all the necessary tools and cabling before installing the switch.
EZ Switch 10/100/1000 • There should be adequate space (approximately two inches) on all sides for proper air flow. • Make sure twisted-pair cable is always routed away from power lines, fluorescent lighting fixtures and other sources of electrical interference such as radios, transmitters, etc. • Make sure that a properly grounded power outlet is within 2 m (6.6 feet) of the switch and is powered from an independent circuit breaker.
EZ Switch 10/100/1000 No crossover cables or other device settings are needed. See the “Cable Specifications” on page 9 of this guide for further information. Caution: 6 Do not plug a phone jack connector into any RJ-45 port. This may damage the switch. Instead, use only twisted-pair cables with RJ-45 connectors that conform with FCC standards.
EZ Switch 10/100/1000 APPLICATION EXAMPLE A typical application for the SMCGS5 is illustrated below.
EZ Switch 10/100/1000 TROUBLESHOOTING Diagnosing Switch Indicators 1. Symptom Power LED does not light after power on. Probable Causes • DC power socket may be defective. Possible Solutions • Check for loose connections. • Check the power outlet by using it for another device. 2. Symptom Link LED does not light after connection is made. Probable Causes • Switch port, network card or cable may be defective. Possible Solutions • Check that the switch and attached device are both powered on.
EZ Switch 10/100/1000 SPECIFICATIONS EZ Switch 10/100/1000 Standards Conformance IEEE 802.3 IEEE 802.3u IEEE 802.3x IEEE 802.
EZ Switch 10/100/1000 DC Input Power 9V, 1A MAC Address Table 8K entries Memory Buffer SMCGS5: 112 Kbits on-chip frame buffer SMCGS8: 144 Kbits on-chip frame buffer Power Consumption All 9 Watts Temperature Operating: 0 ~ 40 ºC / 32 ~ 98 ºF Storage: -40 ~ 70 ºC / -40 ~ 158 ºF Humidity 5% to 95% non-condensing EMC/Safety Compliances CE Mark Immunity EN 61000-4-2/3/4/5/6/8/11 Emissions FCC Class B, CISPR Class B, EN 61000-3-2/3 Safety CSA/NRTL (CSA60950-1 & UL60950-1) TUV/GS (EN60950-1) CB (IEC60950-1) 10
FOR TECHNICAL SUPPORT,CALL: From U.S.A.and Canada (24 hours a day,7 days a week) (800) SMC-4-YOU;Phn:(949) 679-8000;Fax:(949) 679-1481 From Europe :Contact details can be found on www.smc.com INTERNET E-mail address: techsupport@smc.com Driver updates: http://www.smc.com/index.cfm?action=tech_support_drivers_downloads World Wide Web: http://www.smc.com/ For Literature or Advertising Response,Call: U.S.A.
