54Mbps Wireless Voip Router with built-in ADSL Modem From SMC’s line of award-winning connectivity solutions 38 Tesla Irvine, CA 92618 Phone: (949) 679-8000 September 2004 R.01 F 0.33.
Information furnished is believed to be accurate and reliable. However, no responsibility is assumed by our company for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of our company. We reserve the right to change specifications at any time without notice. Copyright © 2004 by SMC Networks, Inc. 38 Tesla Irvine, CA 92618 All rights reserved.
LIMITED WARRANTY Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace any product not operating as warranted with a similar or functionally equivalent product, during the applicable warranty term.
LIMITED WARRANTY WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
COMPLIANCES Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications.
COMPLIANCES The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area.
COMPLIANCES EC Conformance Declaration SMC contact for these products in Europe is: SMC Networks Europe, Edificio Conata II, Calle Fructuós Gelabert 6-8, 2o, 4a, 08970 - Sant Joan Despí, Barcelona, Spain. Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: EN 300 328-1 December 2001 V1.3.1 EN 300 328-2 December 2001 V1.2.1 EN 301 489-1 September 2001 V1.4.
COMPLIANCES Safety Compliance Wichtige Sicherheitshinweise (Germany) 1. Bitte lesen Sie diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine Flüssigoder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung. 4. Die Netzanschlu ßsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6.
TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 About the Barricade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VoIP (Voice over IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TABLE OF CONTENTS Configuring the Voice ADSL Router . . . . . . . . . . . . . . 4-1 Navigating the Management Interface . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Making Configuration Changes . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Channel and SSID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Time Zone . . . . . . . . . . . . . . . . . . . .
TABLE OF CONTENTS Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1 Ethernet Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1 Wiring Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1 RJ-45 Port Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHAPTER 1 INTRODUCTION Congratulations on your purchase of the BarricadeTM g Voice ADSL Router, hereafter referred to as the “Barricade”. We are proud to provide you with a powerful yet simple communication device for connecting your local area network (LAN) to the Internet. For those who want to surf the Internet in the most secure way, this router provides a convenient and powerful solution.
INTRODUCTION digital, the encoding and then compression of the signal into Internet Protocol (IP) packets. The VoIP Router is equipped with a digital signal processor (DSP), which segments the voice signal into frames and stores them in voice packets. Using the industry standard CODECs, G.711, G.723.3 and G.729, these packets are encoded. These IP packets are then transmitted in accordance with International Telecommunications Union specification H.
APPLICATIONS Applications Many advanced networking features are provided by the Barricade: • Wireless and Wired LAN The Barricade provides connectivity to 10/100 Mbps devices, and wireless IEEE 802.11g compatible devices, making it easy to create a network in small offices or homes. • Internet Access This device supports Internet access through an ADSL connection.
INTRODUCTION • DMZ Host Support Allows a networked computer to be fully exposed to the Internet. This function is used when NAT and firewall security prevent an Internet application from functioning correctly. • Security The Barricade supports security features that deny Internet access to specified users, or filter all requests for specific services that the administrator does not want to serve.
CHAPTER 2 INSTALLATION Before installing the BarricadeTM g Voice ADSL Router, verify that you have all the items listed under the Package Contents list. If any of the items are missing or damaged, contact your local distributor. Also be sure that you have all the necessary cabling before installing the Barricade. After installing the Barricade, refer to “Configuring the Voice ADSL Router” on page 4-1.
INSTALLATION System Requirements You must meet the following minimum requirements: • ADSL line installed by your Internet Service Provider. • A PC using a dynamic or fixed IP address, as well as a gateway server address and DNS server address from your service provider. • A computer equipped with a 10/100 Mbps network adapter, a USB-to-Ethernet converter or an IEEE 802.11g wireless network adapter. • TCP/IP network protocols installed on each PC that will access the Internet.
HARDWARE DESCRIPTION The Barricade includes an LED display on the front panel for system power and port indications that simplifies installation and network troubleshooting. It also provides the following ports on the rear panel: Figure 2-1. Rear Panel Item Description Line Connect the telephone line directly to this port. Phone Connect your regular telephone to this port. USB Connect your USB device to this port.
INSTALLATION LED Indicators The power and port LED indicators on the front panel are illustrated by the following figure and table. Figure 2-2. Front Panel LED Status Description PWR On The Barricade is receiving power. Normal operation. Off Power off or failure. On ADSL connection is functioning correctly. Flashing The Barricade is establishing an ADSL link. Off ADSL connection is not established. WLAN Flashing The WLAN port is sending or receiving data.
ISP SETTINGS ISP Settings Please collect the following information from your ISP before setting up the Barricade: • ISP account user name and password • VoIP setting details • Protocol, encapsulation and VPI/VCI circuit numbers • DNS server address • IP address, subnet mask and default gateway (for fixed IP users only) Connect the System The Barricade can be positioned at any convenient location in your office or home. It also can be wall-mounted.
INSTALLATION Connect the ADSL Line Connect the supplied RJ-11 cable from the ADSL Microfilter/Splitter to the ADSL port on your Barricade. When inserting an ADSL RJ-11 plug, be sure the tab on the plug clicks into position to ensure that it is properly seated. Phone Line Configuration Installing a Full-Rate Connection If you are using a full-rate (G.dmt) connection, your service provider will attach the outside ADSL line to a data/voice splitter.
CONNECT THE SYSTEM Installing a Splitterless Connection If you are using a splitterless (G.lite) connection, then your service provider will attach the outside ADSL line directly to your phone system.
INSTALLATION Attach to Your Network Using Ethernet Cabling The four LAN ports on the Barricade auto-negotiate the connection speed to 10 Mbps Ethernet or 100 Mbps Fast Ethernet, as well as the transmission mode to half duplex or full duplex. Use RJ-45 cables to connect any of the four LAN ports on the Barricade to an Ethernet adapter on your PC. Otherwise, cascade any of the LAN ports on the Barricade to an Ethernet hub or switch, and then connect your PC or other network equipment to the hub or switch.
CHAPTER 3 CONFIGURING CLIENT PC After completing hardware setup by connecting all your network devices, you need to configure your computer to connect to the Barricade. See: “Windows 2000” on page 3-3 “Windows XP” on page 3-6 or “Configuring Your Macintosh Computer” on page 3-8 depending on your operating system.
CONFIGURING CLIENT PC TCP/IP Configuration To access the Internet through the Barricade, you must configure the network settings of the computers on your LAN to use the same IP subnet as the Barricade. The default IP settings for the Barricade are: IP Address: 192.168.2.1 Subnet Mask: 255.255.255.
WINDOWS 2000 Windows 2000 1. On the Windows desktop, click Start/Settings/Network and Dial-Up Connections. 2. Click the icon that corresponds to the connection to your Barricade. 3. The connection status screen will open. Click Properties. 4. Double-click Internet Protocol (TCP/IP). 5. If “Obtain an IP address automatically” and “Obtain DNS server address automatically” are already selected, your computer is already configured for DHCP. If not, select this option.
CONFIGURING CLIENT PC Disable HTTP Proxy You need to verify that the “HTTP Proxy” feature of your web browser is disabled. This is so that your browser can view the Barricade’s HTML configuration pages. Determine which browser you use and refer to “Internet Explorer” on page 3-4. Obtain IP Settings from Your Barricade Now that you have configured your computer to connect to your Barricade, it needs to obtain new network settings.
WINDOWS 2000 3. Type “IPCONFIG /RENEW” and press the ENTER key. Verify that your IP Address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.254. These values confirm that your ADSL Router is functioning. 4. Type “EXIT” and press the ENTER key to close the Command Prompt window. Your computer is now configured to connect to the Barricade.
CONFIGURING CLIENT PC Windows XP 1. On the Windows desktop, click Start/Control Panel. 2. In the Control Panel window, click Network and Internet Connections. 3. The Network Connections window will open. Double-click the connection for this device. 4. On the connection status screen, click Properties. 5. Double-click Internet Protocol (TCP/IP). 6. If “Obtain an IP address automatically” and “Obtain DNS server address automatically” are already selected, your computer is already configured for DHCP.
WINDOWS XP 1. On the Windows desktop, click Start/Programs/Accessories/ Command Prompt. 2. In the Command Prompt window, type “IPCONFIG /RELEASE” and press the ENTER key. 3. Type “IPCONFIG /RENEW” and press the ENTER key. Verify that your IP Address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.254. These values confirm that your ADSL router is functioning. Type “EXIT” and press the ENTER key to close the Command Prompt window.
CONFIGURING CLIENT PC Configuring Your Macintosh Computer You may find that the instructions here do not exactly match your operating system. This is because these steps and screenshots were created using Mac OS 10.2. Mac OS 7.x and above are similar, but may not be identical to Mac OS 10.2. Follow these instructions: 1. Pull down the Apple Menu System Preferences . Click 2. Double-click the Network icon in the Systems Preferences window.
CONFIGURING YOUR MACINTOSH COMPUTER 3. If “Using DHCP Server” is already selected in the Configure field, your computer is already configured for DHCP. If not, select this Option. 4. Your new settings are shown on the TCP/IP tab. Verify that your IP Addressisnow192.168.2.xxx,yourSubnetMaskis255.255.255.0and your Default Gateway is 192.168.2.1. These values confirm that your Barricade is functioning. 5. Close the Network window. Now your computer is configured to connect to the Barricade.
CONFIGURING CLIENT PC 3. Uncheck all check boxes and click OK.
CHAPTER 4 CONFIGURING THE VOICE ADSL ROUTER After you have configured TCP/IP on a client computer, you can configure the Barricade using Internet Explorer 5.5 or above. To access the Barricade’s management interface, enter the default IP address of the Barricade in your web browser: http://192.168.2.1. Enter the default password: “smcadmin”, and click “LOGIN”. Note: Passwords can contain from 3~12 alphanumeric characters and are case sensitive.
CONFIGURING THE VOICE ADSL ROUTER Navigating the Management Interface The first page of the web management is Country Selection. You need to select your country before accessing the management interface.
NAVIGATING THE MANAGEMENT INTERFACE The Barricade’s management interface consists of a Setup Wizard and an Advanced Setup section. Setup Wizard: Use the Setup Wizard if you want to quickly set up the Barricade. Go to “SETUP WIZARD” on page 4. Advanced Setup: Advanced Setup supports more advanced functions like VoIP, Firewall, IP and MAC address filtering, virtual server setup, virtual DMZ host, as well as other functions. Go to “Advanced Setup” on page 4-16.
CONFIGURING THE VOICE ADSL ROUTER SETUP WIZARD Channel and SSID Click on “SETUP WIZARD” and “NEXT”, then you will see the Channel and SSID page. Parameter Description ESSID Extended Service Set ID. The ESSID must be the same on the Barricade and all of its wireless clients. ESSID Broadcast Enable or disable the broadcasting of the SSID. Wireless Mode This device supports both 11g and 11b wireless networks. Make your selection depending on the type of wireless network that you have.
SETUP WIZARD Time Zone Select your local time zone from the drop down list. This information is used for log entries and client filtering. For accurate timing of log entries and system events, you need to set the time zone. Select your time zone from the drop down list. If you want to automatically synchronize the Voice ADSL router with a public time server, check the box to Enable Automatic Time Server Maintenance. Select the desired servers from the drop down menu.
CONFIGURING THE VOICE ADSL ROUTER Parameter Setting Select your Country and Internet Service Provider. This will automatically configure the Barricade with the correct Protocol, Encapsulation and VPI/VCI settings for your ISP. If your Country or Internet Service Provider is not listed in this page, you will need to manually enter settings. Go to “Parameter Setting - Country or ISP Not Listed” on page 4-9 in the manual.
SETUP WIZARD Confirm The Confirm page shows a summary of the configuration parameters. Check ADSL operation mode (WAN), Network Layer Parameters (WAN) and ISP parameters are correct. Parameter Description ADSL Operation Mode (WAN) ISP The type of ISP you have selected. Protocol Indicates the protocol used. VPI/VCI Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI). AAL5 Encapsulation Shows the packet encapsulation type. Go to page 4-23 for a detailed description.
CONFIGURING THE VOICE ADSL ROUTER Parameter DNS Server Description The IP address of the DNS server. ISP Parameters Username The ISP assigned user name. Password The password (hidden). DHCP Parameters Function Shows the DHCP function is enabled or disabled. Default Gateway LAN IP address of the Barricade. Subnet Mask The network subnet mask. Name Server 1 Primary DNS server IP address. Name Server 2 Alternate DNS server IP address.
SETUP WIZARD Parameter Setting - Country or ISP Not Listed If your Country or Internet Service Provider is not listed select “Others”. This will allow you to manually configure your ISP settings. For manual configuration you will need to know the Protocol, DNS Server, Encapsulation and VPI/VCI settings used by your ISP. If you have a Static IP address you will also need to know the IP address, Subnet Mask and Gateway address. Please contact your ISP for these details if you do not already have them.
CONFIGURING THE VOICE ADSL ROUTER ISP use Bridging Enter the Bridging settings provided by your ISP. Parameter Description Management IP Address Enter the IP address provided by your ISP. (Default: 192.168.2.1) VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP. Encapsulation Select the encapsulation used by ISP from the drop down list. Click “NEXT” to continue to the “Confirm” settings page.
SETUP WIZARD ISP use 1483Bridging-DHCP Parameter Description DNS Server Domain Name Servers are used to map a domain name (e.g., www.somesite.com) to the equivalent numerical IP address. Your ISP should provide the IP address of a Domain Name Server. Enter the address on this page VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP. Encapsulation Select the encapsulation used by ISP from the drop down list.
CONFIGURING THE VOICE ADSL ROUTER ISP use 1483Bridging-FixIP Parameter Description IP Address Enter your ISP supplied static IP address here Subnet Mask Enter the subnet mask address provided by your ISP. Default Gateway Enter the gateway address provided by your ISP. DNS Server Enter the Domain Name Server address. VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP.
SETUP WIZARD ISP use PPPoE Parameter Description DNS Server Enter the Domain Name Server address. VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP. Encapsulation Select the encapsulation used by ISP from the drop down list. Username Enter user name. Password Enter password. Confirm Password Confirm password Click “NEXT” to continue to the “Confirm” settings page.
CONFIGURING THE VOICE ADSL ROUTER ISP use PPPoA Parameter Description DNS Server Enter the Domain Name Server address. VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP. Encapsulation Select the encapsulation used by ISP from the drop down list. Username Enter user name. Password Enter password. Confirm Password Confirm password Click “NEXT” to continue to the “Confirm” settings page.
SETUP WIZARD ISP use 1483Routing Parameter Description IP Address Enter the IP address provided by your ISP. Subnet Mask Enter the subnet mask address provided by your ISP. Default Gateway Enter the gateway address provided by your ISP. DNS Server Enter the Domain Name Server address. VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP. Encapsulation Select the encapsulation used by ISP from the drop down list.
CONFIGURING THE VOICE ADSL ROUTER Advanced Setup The left-hand side displays the main menu and the right-hand side shows descriptive information. The advanced management interface contains 15 main menu items as described in the following table. 4-16 Menu Description System Sets the local time zone, the password for administrator access, and the IP address of a PC that will be allowed to manage the Barricade remotely. WAN Specifies the Internet connection settings.
ADVANCED SETUP Menu Description SNMP Community string and trap server settings. UPnP Enables the Universal Plug and Play function. ADSL Sets the ADSL operation type and shows the ADSL status. DDNS Configures Dynamic DNS function. VoIP Configures VoIP settings for the VoIP Router, and view VoIP status log. QoS Allows you to optimize voice quality by prioritizing voice over data traffic.
CONFIGURING THE VOICE ADSL ROUTER SYSTEM Time Settings Select your local time zone from the drop down list. This information is used for log entries and client filtering. For accurate timing of log entries and system events, you need to set the time zone. Select your time zone from the drop down list. If you want to automatically synchronize the ADSL router with a public time server, check the box to Enable Automatic Time Server Maintenance. Select the desired servers from the drop down menu.
ADVANCED SETUP Password Settings Use this page to change the password for accessing the management interface. Passwords can contain from 3~12 alphanumeric characters and are case sensitive. Note: If you lost the password, or you cannot gain access to the user interface, press the blue reset button on the rear panel, holding it down for at least five seconds to restore the factory defaults. The default password is “smcadmin”.
CONFIGURING THE VOICE ADSL ROUTER Remote Management By default, management access is only available to users on your local network. However, you can also manage the Barricade from a remote host by entering the IP address of a remote computer on this screen. Check the Enabled check box, and enter the IP address of the Host Address and click “APPLY”. Note: If you check Enable and specify an IP address of 0.0.0.0, any remote host can manage the Barricade.
ADVANCED SETUP DNS Domain Name Servers (DNS) are used to map a domain name (e.g., www.smc.com) with the IP address (e.g., 64.147.25.20). Your ISP should provide the IP address of one or more Domain Name Servers. Enter those addresses on this page, and click “APPLY”.
CONFIGURING THE VOICE ADSL ROUTER WAN Specify the WAN connection parameters provided by your Internet Service Provider (ISP).
ADVANCED SETUP ATM PVC Enter the ATM (Asynchronous Transfer Mode) virtual connection parameters here. Parameter Description Description Click on the VC to set the values for the connection. VPI/VCI Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI). Encapsulation Specifies how to handle multiple protocols at the ATM transport layer.
CONFIGURING THE VOICE ADSL ROUTER ATM Interface 1483 Bridging Enter the Bridging settings provided by your ISP. Parameter Description VPI/VCI Data flows are broken up into fixed length cells, each of which contains a Virtual Path Identifier (VPI) that identifies the path between two nodes, and a Virtual Circuit Identifier (VCI) that identifies the data channel within that virtual path. Each virtual circuit maintains a constant flow of cells between the two end points.
ADVANCED SETUP PPPoA Parameter Description VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP. Encapsulation Select the encapsulation used by ISP from the drop down list. QoS Class ATM QoS classes including CBR, UBR and VBR PCR/SCR/MBS QoS Parameters - PCR, SCR and MBS are configurable. IP assigned by ISP Select Yes if the IP address was provided by your ISP IP Address Enter the IP address provided by your ISP.
CONFIGURING THE VOICE ADSL ROUTER 1483 Routing 4-26 Parameter Description IP Address Enter the IP address provided by your ISP. Subnet Mask Enter the subnet mask address provided by your ISP. Default Gateway Enter the gateway address provided by your ISP. VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP. Encapsulation Select the encapsulation used by ISP from the drop down list.
ADVANCED SETUP PPPoE Parameter Description IP Address Enter the IP address provided by your ISP. Subnet Mask Enter the subnet mask address provided by your ISP. VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP. Encapsulation Select the encapsulation used by ISP from the drop down list. QoS Class ATM QoS classes including CBR, UBR and VBR PCR/SCR/MBS QoS Parameters - PCR, SCR and MBS are configurable.
CONFIGURING THE VOICE ADSL ROUTER MAC Encapsulated Routing Parameter 4-28 Description IP Address Enter the IP address provided by your ISP. Subnet Mask Enter the subnet mask address provided by your ISP. Default Gateway Enter the gateway address provided by your ISP. VPI/VCI Enter the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) supplied by your ISP. Encapsulation Select the encapsulation used by ISP from the drop down list.
ADVANCED SETUP Clone MAC Address Some ISPs require you to register your MAC address with them. If this is the case, the MAC address of the Barricade must be changed to the MAC address that you have registered with your ISP.
CONFIGURING THE VOICE ADSL ROUTER LAN Use the LAN menu to configure the LAN IP address and to enable the DHCP server for dynamic client address allocation. Parameter Description LAN IP IP Address The IP address of the Barricade. IP Subnet Mask The subnet mask of the network. DHCP Server The Barricade comes with the DHCP function. To dynamically assign an IP address to client PCs, enable this function. Lease Time Set the IP lease time.
ADVANCED SETUP WIRELESS The Barricade also operates as a wireless access point, allowing wireless computers to communicate with each other. To configure this function, all you need to do is enable the wireless function, define the radio channel, the domain identifier, and the security options. Check Enable and click “SAVE SETTINGS”.
CONFIGURING THE VOICE ADSL ROUTER Channel and SSID You must specify a common radio channel and SSID (Service Set ID) to be used by the Barricade and all of its wireless clients. Be sure you configure all of its clients to the same values. Parameter Description ESSID Extended Service Set ID. The ESSID must be the same on the Barricade and all of its wireless clients. ESSID Broadcast Enable or disable the broadcasting of the SSID. Wireless Mode This device supports both 11g and 11b wireless networks.
ADVANCED SETUP Access Control restrict access based on MAC address 4-33
CONFIGURING THE VOICE ADSL ROUTER Security To make your wireless network safe, you should turn on the security function. The Barricade supports WEP (Wired Equivalent Privacy) and WPA (Wi-Fi Protected) security mechanisms.
ADVANCED SETUP WEP If you want to use WEP to protect your wireless network, you need to set the same parameters for the Barricade and all your wireless clients. Parameter WEP Mode Description Select 64 bit or 128 bit key to use for encryption. Key Entry Method Select Hex or ASCII to use for encryption key Key Provisioning Select Static if there is only one fixed key for encryption. If you want to select Dynamic, you would need to enable 802.1X function first.
CONFIGURING THE VOICE ADSL ROUTER To manually configure the encryption key, enter five hexadecimal pairs of digits for each 64-bit key, or enter 13 pairs for the single 128-bit key. (A hexadecimal digit is a number or letter in the range 0-9 or A-F.) Note that WEP protects data transmitted between wireless nodes, but does not protect any transmissions over your wired network or over the Internet. WPA Wi-Fi Protected Access (WPA) combines temporal key integrity protocol (TKIP) and 802.1X mechanisms.
ADVANCED SETUP Parameter Description Pre-shared Key Type in the key here. Group Key Re_Keying The period of renewing broadcast/multicast key. 802.1X If 802.1X is used in your network, then you should enable this function for the Barricade. Parameter Description 802.1X Authentication Enable or disable this authentication function. Session Idle timeout Defines a maximum period of time for which the connection is maintained during inactivity.
CONFIGURING THE VOICE ADSL ROUTER Parameter Description Quiet Period Defines a maximum period of time for which the Barricade will wait between failed authentications. Server Type Select TINY or RADIUS as the authentication server. RADIUS Server Parameters 4-38 Server IP The IP address of your authentication server. Server Port The port used for the authentication service. Secret Key The secret key shared between the authentication server and its clients.
ADVANCED SETUP NAT Network Address Translation allows multiple users to access the Internet sharing one public IP.
CONFIGURING THE VOICE ADSL ROUTER Address Mapping Allows one or more public IP addresses to be shared by multiple internal users. This also hides the internal network for increased privacy and security. Enter the Public IP address you wish to share into the Global IP field. Enter a range of internal IPs that will share the global IP into the “from” field.
ADVANCED SETUP Virtual Server If you configure the Barricade as a virtual server, remote users accessing services such as web or FTP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP addresses. In other words, depending on the requested service (TCP/UDP port number), the Barricade redirects the external service request to the appropriate server (located at another internal IP address).
CONFIGURING THE VOICE ADSL ROUTER Special Application Some applications require multiple connections, such as Internet gaming, video-conferencing, and Internet telephony. These applications may not work when Network Address Translation (NAT) is enabled. If you need to run applications that require multiple connections, use these pages to specify the additional public ports to be opened for each application.
ADVANCED SETUP NAT Mapping Table This page displays the current NAPT (Network Address Port Translation) address mappings.
CONFIGURING THE VOICE ADSL ROUTER ROUTING These pages define routing related parameters, including static routes and RIP (Routing Information Protocol) parameters. Static Route Parameter Description Index Check the box of the route you wish to delete or modify. Network Address Enter the IP address of the remote computer for which to set a static route. Subnet Mask Enter the subnet mask of the remote network for which to set a static route.
ADVANCED SETUP RIP Parameter Description General RIP Parameters RIP mode Globally enables or disables RIP. Auto summary If Auto summary is disabled, then RIP packets will include sub-network information from all subnetworks connected to the router. If enabled, this sub-network information will be summarized to one piece of information covering all subnetworks. Table of current Interface RIP parameter Interface The WAN interface to be configured.
CONFIGURING THE VOICE ADSL ROUTER Parameter Poison Reverse Authentication Required Authentication Code Description A method for preventing loops that would cause endless retransmission of data traffic. • None: No authentication. • Password: A password authentication key is included in the packet. If this does not match what is expected, the packet will be discarded. This method provides very little security as it is possible to learn the authentication key by watching RIP packets.
ADVANCED SETUP Routing Table Parameter Description Flags Indicates the route status: C = Direct connection on the same subnet. S = Static route. R = RIP (Routing Information Protocol) assigned route. I = ICMP (Internet Control Message Protocol) Redirect route. Network Address Netmask Destination IP address. The subnetwork associated with the destination. This is a template that identifies the address bits in the destination address used for routing to specific subnets.
CONFIGURING THE VOICE ADSL ROUTER FIREWALL The Barricade Router’s firewall inspects packets at the application layer, maintains TCP and UDP session information including time-outs and the number of active sessions, and provides the ability to detect and prevent certain types of network attacks. Network attacks that deny access to a network device are called Denial-of-Service (DoS) attacks. DoS attacks are aimed at devices and networks with a connection to the Internet.
ADVANCED SETUP Access Control Access Control allows users to define the outgoing traffic permitted or not-permitted through the WAN interface. The default is to permit all outgoing traffic. The following items are on the Access Control screen: Parameter Description Enable Filtering Function Click Yes to turn on the filtering function. Normal Filtering Table Displays the IP address (or an IP address range) filtering table.
CONFIGURING THE VOICE ADSL ROUTER To add the PC to the filtering table: 1. Click “Add PC” on the Access Control screen. 2. Define the appropriate settings for client PC services. 3. Click “OK” and then click “SAVE SETTINGS” to save your settings.
ADVANCED SETUP MAC Filter The Barricade can also limit the access of hosts within the local area network (LAN). The MAC Filtering Table allows the Barricade to enter up to 32 MAC addresses that are not allowed access to the WAN port. Click Yes to enable, or No to disable this function. Enter the MAC address in the space provided.
CONFIGURING THE VOICE ADSL ROUTER URL Blocking The Barricade allows the user to block access to web sites by entering either a full URL address or just a keyword. This feature can be used to protect children from accessing violent or pornographic web sites. You can define up to 30 sites here.
ADVANCED SETUP Schedule Rule You may filter Internet access for local clients based on rules. Each access control rule may be activated at a scheduled time. Define the schedule on the Schedule Rule page, and apply the rule on the Access Control page.
CONFIGURING THE VOICE ADSL ROUTER Follow these steps to add a schedule rule: 1. Click “Add Schedule Rule”. 2. Define the appropriate settings for a schedule rule. 3. Click “OK” and then click “SAVE SETTINGS” to save your settings.
ADVANCED SETUP Intrusion Detection • Intrusion Detection Feature Stateful Packet Inspection (SPI) and Anti-DoS firewall protection (Default: Enabled) — The Intrusion Detection Feature of the Barricade Router limits access for incoming traffic at the WAN port. When the SPI feature is turned on, all incoming packets will be blocked except for those types marked in the Stateful Packet Inspection section.
CONFIGURING THE VOICE ADSL ROUTER 4-56
ADVANCED SETUP • Stateful Packet Inspection This is called a “stateful” packet inspection because it examines the contents of the packet to determine the state of the communications; i.e., it ensures that the stated destination computer has previously requested the current communication. This is a way of ensuring that all communications are initiated by the recipient computer and are taking place only with sources that are known and trusted from previous interactions.
CONFIGURING THE VOICE ADSL ROUTER • Connection Policy Enter the appropriate values for TCP/UDP sessions as described in the following table. Parameter Defaults Description Fragmentation half-open wait 10 sec Configures the number of seconds that a packet state structure remains active. When the timeout value expires, the router drops the unassembled packet, freeing that structure for use by another packet.
ADVANCED SETUP • DoS Criteria and Port Scan Criteria Set up DoS and port scan criteria in the spaces provided (as shown below). Parameter Defaults Description Total incomplete TCP/UDP sessions HIGH 300 sessions Defines the rate of new unestablished sessions that will cause the software to start deleting half-open sessions. Total incomplete TCP/UDP sessions LOW 250 sessions Defines the rate of new unestablished sessions that will cause the software to stop deleting halfopen sessions.
CONFIGURING THE VOICE ADSL ROUTER DMZ If you have a client PC that cannot run an Internet application properly from behind the firewall, you can open the client up to unrestricted twoway Internet access. Enter the IP address of a DMZ (Demilitarized Zone) host on this screen. Adding a client to the DMZ may expose your local network to a variety of security risks, so only use this option as a last resort.
ADVANCED SETUP SNMP Use the SNMP configuration screen to display and modify parameters for the Simple Network Management Protocol (SNMP). Community A computer attached to the network, called a Network Management Station (NMS), can be used to access this information. Access rights to the agent are controlled by community strings. To communicate with the Barricade, the NMS must first submit a valid community string for authentication.
CONFIGURING THE VOICE ADSL ROUTER Trap Specify the IP address of the NMS to notify when a significant event is detected by the agent. When a trap condition occurs, the SNMP agent sends an SNMP trap message to any NMS specified as a trap receiver. Parameter Description IP Address Traps are sent to this address when errors or specific events occur on the network. Community A community string (password) specified for trap management.
ADVANCED SETUP UPNP The Universal Plug and Play architecture offers pervasive peer-to-peer network connectivity of PCs of all form factors, intelligent appliances, and wireless devices. UPnP enables seamless proximity network in addition to control and data transfer among networked devices in the office, home and everywhere within your network.
CONFIGURING THE VOICE ADSL ROUTER ADSL ADSL (Asymmetric Digital Subscriber Line) is designed to deliver more bandwidth downstream (from the central office to the customer site) than upstream. This section is used to configure the ADSL operation type and shows the ADSL status. ADSL Parameters Parameter Operation Mode Description • Automatic • T1.413 Issue 2 • G.992.1 (G.DMT) • G.992.2 (G.Lite) This page is designed for the engineer to test the ADSL loop condition.
ADVANCED SETUP ADSL Status The Status screen displays information on connection line status, data rate, operation data and defect indication, and statistics. Scroll down to view more information.
CONFIGURING THE VOICE ADSL ROUTER The following items are included on this information page: Parameter Description Status Line Status Shows the current status of the ADSL line connection. Data Rate Upstream Maximum upstream data rate. Downstream Maximum downstream data rate. Operation Data/Defect Indication 4-66 Noise Margin Maximum upstream and downstream noise margin. Output Power Maximum fluctuation in the output power.
ADVANCED SETUP Parameter Description Statistics (Superframes represent the highest level of data presentation. Each superframe contains regular ADSL frames, one of which is used to provide superframe synchronization, identifying the start of a superframe. Some of the remaining frames are also used for special functions.) Received Superframes Interleaved Number of interleaved superframes received. Transmitted Superframes Interleaved Number of interleaved superframes transmitted.
CONFIGURING THE VOICE ADSL ROUTER DDNS Dynamic Domain Name Service (DDNS) provides users on the Internet with a method to tie their domain name to a computer or server. DDNS allows your domain name to follow your IP address automatically by having your DNS records changed when your IP address changes. This DNS feature is powered by DynDNS.org or TZO.com. With a DDNS connection you can host your own web site, email server, FTP site, and more at your own location even if you have a dynamic IP address.
ADVANCED SETUP VOIP Dial Setting Parameter Description Prefix setting International Enter the prefix for dialing international calls. Long Distance Enter the prefix for dialing long distance calls. Local Information Country Code Enter your country code here. Area Code Enter your area code here. Group ID Use Group ID Check this box to use the group ID mechanism. Use Group ID for PSTN Number Check this box to use the group ID for your PSTN phone number. Group ID Enter your Group ID here.
CONFIGURING THE VOICE ADSL ROUTER Port Setting_for Phone You can configure the port settings for your phone in this page. Parameter Description Port General Setting Port Status Check this box to enable the function. Port Type Select phone set or PBX CO line. Extension Number If you have an extension number, enter it here. FAX Support Select the FAX function that you desire. Security Setting Allows to Make Check the type of calls that’s allowed using this phone set.
ADVANCED SETUP Port Setting_for Line You can configure the port settings for your phone line in this page. Parameter Description Port General Setting Port Status Check this box to enable the function. Port Type Select Relay mode or Dedicated line. Security Setting Allows to Make Check the type of calls that’s allowed using this line. VOIP Authentication Check this box to perform authentication when making voice calls. Advanced setting Click the “Adv Setting” button to set detailed parameters.
CONFIGURING THE VOICE ADSL ROUTER 4-72
ADVANCED SETUP Outgoing Mode Select the outgoing mode to find the peer gateway, two modes are supported: enterprise mode and ITSP mode. Click “Next” to proceed with the detailed configurations.
CONFIGURING THE VOICE ADSL ROUTER ITSP mode 4-74
ADVANCED SETUP H.323 Setting Parameter Description H.323 H.323 Version This is the version of the H.323 protocol. H.245Mode Select the mode for H.245. Time to Live Set the TTL time in seconds. Endpoint Type Choose the endpoint type: terminal or gateway. Q.931 Port Set the port to use for Q.931. Other Options Enable the functions that you want to use with this device. Alias H.323 ID Select the item that you want to use. URL ID Enter your URL ID here. Email ID Enter your email ID here.
CONFIGURING THE VOICE ADSL ROUTER The device supports the following codecs, use the left and right arrows to select the Codes to use, and use the up and down buttons to arrange the priority. Numbering Plan An alias address in RAS or Q.931 may represent an endpoint or it may represent conferences that an endpoint is hosting. An alias address can be used when the actual address of an endpoint (or the conference ID) is not known.
ADVANCED SETUP Parameter Category Description Select the category that you want to configure. Alias Address Choice Select the name that you want to use as the Alias. Number Policy Check the option that you want to use. Click the “additional numbering” button to add an additional number. Parameter Description Additional Numbering Plan Check to enable or disable this function. Manipulating Rules This table shows the rule information of your numbering plans. Add New Rule Click to add new rules.
CONFIGURING THE VOICE ADSL ROUTER PBX ID/Prefix The current Prefix (PBX ID or E.164 Number Prefix) is listed in this table. Click the “Add” button to add a new entry, or click “Delete” or “Modify” to change the selected entry. Peer Gateway The current incoming peer gateway entries information is listed in this table. Click “Add” to add a new entry, or click the “Delete” or “Modify” button to change the selected entry.
ADVANCED SETUP User Management The current Phone User Information is listed in this table. Click the “Add” button to add a new entry, or click “Delete” or “Modify” to change the selected entry. VOIP Status This page displays the phone port status and the Gatekeeper status.
CONFIGURING THE VOICE ADSL ROUTER QOS The QoS (Quality of Service) function allows you to differentiate VoIP traffic and provide it with high-priority forwarding service. In addition, you can specify the outgoing VC of VoIP packets to further guarantee the voice quality. 4-80 Parameter Description Enable or disable QoS module function Check to enable or disable this function. Direct VoIP to VC Select the Virtual Connection.
ADVANCED SETUP TOOLS Use the Tools menu to backup the current configuration, restore a previously saved configuration, restore factory settings, update firmware, and reset the Barricade. Configuration Tools Choose a function and click Next. Backup allows you to save the Barricade’s configuration to a file. Restore can be used to restore the saved backup configuration file. Restore to Factory Defaults resets the Barricade back to the original settings. You will be asked to confirm your decision.
CONFIGURING THE VOICE ADSL ROUTER Firmware Upgrade Use this screen to update the firmware or user interface to the latest versions. Download the upgrade file from the SMC web site first, and save it to your hard drive. In the Upgrade Target field, choose Firmware. Then click “Browse...” to look for the downloaded file. Click “BEGIN UPGRADE”. Check the Status page Information section to confirm that the upgrade process was successful.
ADVANCED SETUP Reset Click “REBOOT ROUTER” to reset the Barricade. The reset will be complete when the power LED stops blinking. If you perform a reset from this page, the configurations will not be changed back to the factory default settings. Note: If you use the Reset button on the back panel, the Barricade performs a power reset. If the button is pressed for over five seconds, all the LEDs will illuminate and the factory default settings will be restored.
CONFIGURING THE VOICE ADSL ROUTER STATUS The Status page displays WAN/LAN connection status, firmware, and hardware version numbers, illegal attempts to access your network, as well as information on DHCP clients connected to your network. The security log may be saved to a file by clicking “Save” and choosing a location. Scroll down to view more information on the Status page.
ADVANCED SETUP 4-85
CONFIGURING THE VOICE ADSL ROUTER The following items are included on the Status page: Parameter Description INTERNET Displays WAN connection type and status. Release Renew GATEWAY Click on this button to disconnect from the WAN. Click on this button to establish a connection to the WAN. Displays system IP settings, as well as DHCP Server and Firewall status.
FINDING THE MAC ADDRESS OF A NETWORK CARD Finding the MAC address of a Network Card WINDOWS NT4/2000/XP Click Start/Programs/Command Prompt. Type “ipconfig /all” and press “ENTER”. The MAC address is listed as the “Physical Address.” MACINTOSH Click System Preferences/Network. The MAC address is listed as the “Ethernet Address” on the TCP/IP tab. LINUX Run the command “/sbin/ifconfig.” The MAC address is the value after the word “HWaddr.
APPENDIX A TROUBLESHOOTING This section describes common problems you may encounter and possible solutions to them. The Barricade can be easily monitored through panel indicators to identify problems. Troubleshooting Chart Symptom Action LED Indicators Power LED is Off • Check connections between the Barricade, the external power supply, and the wall outlet.
TROUBLESHOOTING Troubleshooting Chart Symptom Action LED Indicators Link LED is Off • Verify that the Barricade and attached device are powered on. • Be sure the cable is plugged into both the Barricade and the corresponding device. • Verify that the proper cable type is used and that its length does not exceed the specified limits. • Be sure that the network interface on the attached device is configured for the proper communication speed and duplex mode.
TROUBLESHOOTING Troubleshooting Chart Symptom Action Management Problems Cannot connect using the web browser Forgot or lost the password • Be sure to have configured the Barricade with a valid IP address, subnet mask, and default gateway. • Check that you have a valid network connection to the Barricade and that the port you are using has not been disabled. • Check the network cabling between the management station and the Barricade.
TROUBLESHOOTING Troubleshooting Chart Symptom Action Wireless Problems A wireless PC cannot associate with the Barricade. • Make sure the wireless PC has the same SSID settings as the Barricade. See “Channel and SSID” on page 4-32 • You need to have the same security settings on the clients and the Barricade. See “Access Control” on page 4-33. The wireless network is often interrupted. • Move your wireless PC closer to the Barricade to find a better signal.
APPENDIX B CABLES Ethernet Cable Caution: DO NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards. Specifications Cable Types and Specifications Cable Type Max. Length Connector 10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45 100 m (328 ft) RJ-45 100BASE-TX Cat. 5 100-ohm UTP Wiring Conventions For Ethernet connections, a twisted-pair cable must have two pairs of wires.
CABLES Each wire pair must be attached to the RJ-45 connectors in a specific orientation. The following figure illustrates how the pins on an Ethernet RJ-45 connector are numbered. Be sure to hold the connectors in the same orientation when attaching the wires to the pins. Figure B-1. RJ-45 Ethernet Connector Pin Numbers RJ-45 Port Connection Use the straight-through CAT-5 Ethernet cable provided in the package to connect the Barricade to your PC.
ETHERNET CABLE Pin Assignments With 100BASE-TX/10BASE-T cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6 for receiving data. RJ-45 Pin Assignments Pin Number Assignment1 1 Tx+ 2 Tx- 3 Rx+ 6 Rx- 1: The “+” and “-” signs represent the polarity of the wires that make up each wire pair. Straight-Through Wiring If the port on the attached device has internal crossover wiring (MDI-X), then use straight-through cable.
CABLES Crossover Wiring If the port on the attached device has straight-through wiring (MDI), use crossover cable.
ADSL CABLE ADSL Cable Use standard telephone cable to connect the RJ-11 telephone wall outlet to the RJ-45 ADSL port on the ADSL Router. Caution: Do not plug a phone jack connector into an RJ-45 port. Specifications Cable Types and Specifications Cable Type Connector ADSL Line Standard Telephone Cable RJ-11 Wiring Conventions For ADSL connections, a cable requires one pair of wires. Each wire is identified by different colors. For example, one wire might be red and the other, red with white stripes.
Blue/White White/Blue White/Orange Blue/White White/Blue Orange/White Black Red Green Yellow CABLES R1 T1 T2 R1 T1 R2 T2 R1 T1 R2 123456 123456 123456 6x2 Jack 6x4 Jack 6x4 Jack T = Tip Pin Signal Name 1 Not used 2 Line 2 Tip Black or White/Orange 3 Line 1 Ring Red or Blue/White 4 Line 1 Tip Green or White/Blue 5 Line 2 Ring Yellow or Orange/White 6 Not used Figure B-3.
APPENDIX C SPECIFICATIONS Physical Characteristics Ports Four 10/100Mbps RJ-45 ports One ADSL RJ-11 port One Phone port One Line port ADSL Features Supports DMT line modulation Supports Annex A Full-Rate ADSL: up to 8 Mbps downstream, up to 1 Mbps upstream (G.992.1 &T1.413, Issue 2) Supports G.Lite ADSL: up to 1.
SPECIFICATIONS Security Features Password protected configuration access User authentication (PAP/CHAP) with PPP Firewall NAT NAPT VPN pass through (IPSec-ESP Tunnel mode,L2TP, PPTP) LAN Features IEEE 802.1D (self-learning transparent Bridging) DHCP Server DNS Proxy Static Routing, RIPv1 and RIP VoIP Features H.323 Codec - G.711, G.723, G.729a, G.168 Modulation Type OFDM, CCK Radio Features Wireless RF module Frequency Band 802.11g Radio: 2.4GHz 802.11b Radio: 2.
SPECIFICATIONS Operating Channels IEEE 802.11b compliant: 11 channels (US, Canada) 13 channels (ETSI) 2 Channels (Spain) 4 Channels (France) 14 channels (Japan) Operating Channels IEEE 802.11g compliant: 13 channels (US, Canada, Europe, Japan) RF Output Power Modulation Rate-Output Power (dBm) 802.11b - 1Mbps 16 802.11b - 2Mbps 16 802.11b - 5.5Mbps 16 802.11b - 11Mbps 16 Modulation Rate-Output Power (dBm) 802.11g - 6Mbps 15 802.11g - 9Mbps 15 802.11g - 12Mbps 15 802.11g - 18Mbps 15 802.11g- 24Mbps 15 802.
SPECIFICATIONS Modulation Rate-Receiver Sensitivity Typical (dBm) 802.11g - 6Mbps -88 802.11g - 9Mbps -87 802.11g - 12Mbps -84 802.11g - 18Mbps -82 802.11g - 24Mbps -79 802.11g - 36Mbps -75 802.11g - 48Mbps -68 802.
SPECIFICATIONS Standards Conformance Electromagnetic Compatibility CE, ETSI, R&TTE, FCC part 15 class B & FCC part 68, ETS 300 328, ETS 300 826 Safety CSA/NRTL (UL1950, CSA 22.2.
