Manual
Table Of Contents
- ANSI C63.17-2006 Front Cover
- Title page
- Introduction
- Notice to users
- Participants
- Contents
- American National Standard Methods of Measurement of the Electromagnetic and Operational Compatibility of Unlicensed Personal Communications Services (UPCS) Devices
- 1. Overview
- 2. Normative references
- 3. Definitions, symbols, acronyms, and abbreviations
- 4. Radiated and conducted emissions test methodology
- 4.1 Test facilities and equipment
- 4.2 Test configurations and setup
- 4.3 Transmitted power and monitoring threshold limits
- 4.4 Limits for radiated and conducted tests
- 4.5 Conducted measurements of products with identical collocated transmitting and monitoring antennas
- 4.6 Conducted measurements of products with collocated transmitting and monitoring antennas of different types
- 4.7 Conducted measurements of products with arbitrarily placed transmitting and monitoring antennas
- 4.8 Radiated measurements of products with identical collocated transmitting and monitoring antennas
- 4.9 Radiated measurements of products with collocated transmitting and monitoring antennas of different types
- 4.10 Radiated measurements of products with arbitrarily placed transmitting and monitoring antennas
- 4.11 Manufacturer’s declarations and descriptions
- 5. Measurement instrumentation
- 6. RF measurements
- 7. Monitoring tests
- 8. Time and spectrum window access procedure
- 9. Test report
- 9.1 Test report contents
- 9.2 Applicable standards
- 9.3 Equipment units tested
- 9.4 Test configuration
- 9.5 List of test equipment
- 9.6 Units of measurement
- 9.7 Location of test site
- 9.8 Measurement procedures
- 9.9 Reporting measurement data
- 9.10 General and special conditions
- 9.11 Summary of results
- 9.12 Required signatures
- 9.13 Test report appendixes
- 9.14 Test report disposition
- Annex A (informative) 47CFR15, Subpart D—Rules and test cases for UPCS devices
- Annex B (informative) Radiated and conducted measurement of power output and monitoring thresholds
- Annex C (informative) Options for implementing the tests of Clause 7 and Clause 8
ANSI C63.17-2006
Methods of Measurement of the Electromagnetic and Operational Compatibility of UPCS Devices
4.11
5.
Manufacturer’s declarations and descriptions
Before testing, the manufacturer shall provide declared values of the following parameters for the EUT
being tested to the testing organization:
⎯ The channel plan
⎯ Maximum EUT antenna gain G
A
(dBi), and orientation and polarization for maximum gain
⎯ Maximum peak power level
⎯ Emission bandwidth
⎯ Nominal receive bandwidth
⎯ Frame period and time slot plan, if time-division multiple-access (TDMA) techniques are used
⎯ Minimum and maximum burst length, if TDMA techniques are used
⎯ Minimum and maximum operating temperature ranges declared to the end user
⎯ Whether a system built with the EUT does or does not operate under the provisions of
47CFR15.323(c)(10) to test for deferral only in conjunction with a companion device
⎯ Whether a system built with the EUT does or does not implement the provisions of 47CFR15.323(c)(5)
enabling the use of the upper threshold for deferral
⎯ The nominal value of the deferral threshold
⎯ Whether a system built using the EUT does or does not operate under the provisions of
47CFR15.323(c)(6) incorporating provisions for waiting for a channel to go clear
⎯ Whether a system built using the EUT does or does not operate under the provisions of
47CFR15.323(c)(11) enabling the access criteria check on the receive channel while in the presence of
collocated interferers
⎯ The provisions within the EUT for self-check, by which compliance with 47CFR15.319(f) is obtained
⎯ Whether the EUT does or does not have the monitoring made through the radio receiver used for
communication
⎯ Whether the EUT does or does not transmit control and signaling channel(s)
⎯ Nominal mains and battery voltage
The manufacturer shall describe the channel monitoring and selection process used by the EUT, including
details regarding the time between monitoring and transmission on the confirmed channel. Appropriate
timing diagrams shall be included as necessary.
If the manufacturer claims exemption from the tests of 7.4, then the manufacturer shall declare and provide
proper evidence that the monitoring is made through the radio receiver used for communication.
Measurement instrumentation
See informative Annex C.
14
Copyright © 2007 IEEE. All rights reserved.
Licensed to Sid Sanders. ANSI order X_30788. Downloaded 11/19/2007 2:45 PM. Single user license only. Copying and networking prohibited.