USER GUIDE BarricadeTM N 150Mbps Wireless-N Mini 3G Broadband Router SMCWBR11S-3GN
BarricadeTM SMCWBR11S-3GN User Guide SMC Networks U.S.A 20 Mason Irvine, CA 92618 Phone: (949) 679-8000 SMC Networks Europe C/Fructuós Gelabert 6-8, 2º, 2ª Edificio Conata II 08970 Sant Joan Despí, Barcelona, Spain Phone: +34 93 477 4920 March 2010 Pub.
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright © 2010 by SMC Networks, Inc.
WARRANTY AND PRODUCT REGISTRATION To register SMC products and to review the detailed warranty statement, please refer to the Support Section of the SMC Website at http:// www.smc.com.
COMPLIANCES FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
COMPLIANCES The following three 3G cards have passed the co-located EMC/RF exposure test with this device and can be used with this device. Other 3G cards may or may not comply with FCC rules, please consult the manufacturer before purchase.
COMPLIANCES TAIWAN NCC 根據國家通信傳播委員會低功率電波輻射性電機管理辦法規定： 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更 頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應 立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通 信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 EC CONFORMANCE DECLARATION SMC contact for these products in Europe is: SMC Networks Europe, C/Fructuós Gelabert 6-8, 2o, 2a, Edificio Conata II, 08970 - Sant Joan Despí, Barcelona, Spain.
COMPLIANCES ◆ This device will automatically limit the allowable channels determined by the current country of operation. Incorrectly entering the country of operation may result in illegal operation and may cause harmful interference to other systems. The user is obligated to ensure the device is operating according to the channel limitations, indoor/outdoor restrictions and license requirements for each European Community country as described in this document.
COMPLIANCES Polish Polski Niniejszym Manufacturer oświadcza, że Radio LAN device jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Portuguese Português Manufacturer declara que este Radio LAN device está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovak Slovensky Manufacturer týmto vyhlasuje, že Radio LAN device spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
ABOUT THIS GUIDE PURPOSE This guide gives specific information on how to install the Mini 3G Broadband Router and its physical and performance related characteristics. It also gives information on how to operate and use the management functions of the Mini 3G Broadband Router. AUDIENCE This guide is for users with a basic working knowledge of computers. You should be familiar with Windows operating system concepts.
CONTENTS SECTION I WARRANTY AND PRODUCT REGISTRATION 4 COMPLIANCES 5 ABOUT THIS GUIDE 10 CONTENTS 11 FIGURES 15 TABLES 18 GETTING STARTED 1 INTRODUCTION 19 20 Key Hardware Features 20 Description of Capabilities 20 Applications 21 Package Contents 22 Hardware Description 22 LED Indicators 24 Ethernet WAN Port 25 Ethernet LAN Port 25 3G Modem USB Port 25 Power Connector 25 WPS Button 25 Reset Button 25 2 NETWORK PLANNING 26 Internet Gateway Router 26 LAN Access Poi
CONTENTS System Requirements 29 Mounting the Device 30 Mounting on a Wall 30 Mounting on a Horizontal Surface 30 Router Mode Connections 31 Bridge Mode Connections 32 4 INITIAL CONFIGURATION SECTION II 34 ISP Settings 34 Connecting to the Login Page 34 Home Page and Main Menu 35 Common Web Page Buttons 36 Setup Wizard 36 Step 1 - Language Selection 36 Step 2 - Time Settings 37 Step 3 - WAN Settings - DHCP 37 Step 3 - WAN Settings - Static IP 39 Step 3 - WAN Settings - PPPoE
CONTENTS 3G 62 LAN Setting 66 DHCP Clients 68 Advanced Routing 69 Advanced Routing Settings 69 Routing Table 70 Dynamic Route 71 7 WIRELESS CONFIGURATION 72 Basic Settings 72 HT Physical Mode Settings Advanced Settings 75 76 Advanced Wireless 77 Wi-Fi Multimedia 79 Multicast-to-Unicast Converter 81 WLAN Security 82 Wired Equivalent Privacy (WEP) 83 WPA Pre-Shared Key 84 WPA Enterprise Mode 85 IEEE 802.
CONTENTS SECTION III DDNS Settings 109 Firmware Upgrade 110 Configuration Settings 111 System Status 112 Statistics 114 System Log 115 3G Budget Status 116 APPENDICES 119 A TROUBLESHOOTING 120 Diagnosing LED Indicators 120 If You Cannot Connect to the Internet 120 Before Contacting Technical Support 121 B HARDWARE SPECIFICATIONS 122 C CABLES AND PINOUTS 124 Twisted-Pair Cable Assignments 124 10/100BASE-TX Pin Assignments 125 Straight-Through Wiring 125 Crossover Wiring 1
FIGURES Figure 1: Top Panel 23 Figure 2: Rear Panel 23 Figure 3: LEDs 24 Figure 4: Bottom Panel 25 Figure 5: Operating as an Internet Gateway Router 26 Figure 6: Operating as an Access Point 27 Figure 7: Operating as a Wireless Bridge 28 Figure 8: Operating as a Wireless Repeater 28 Figure 9: Wall Mounting 30 Figure 10: Router Mode Connection 31 Figure 11: Bridge Mode Connection 32 Figure 12: Login Page 35 Figure 13: Home Page 35 Figure 14: Wizard Step 1 - Language Selection 36
FIGURES Figure 32: 3G Configuration - Account Setup 63 Figure 33: 3G Configuration - Budget Control 64 Figure 34: 3G Configuration - E-mail Settings 65 Figure 35: LAN Configuration 66 Figure 36: DHCP Clients 68 Figure 37: Advanced Routing (Router Mode) 69 Figure 38: Basic Settings 73 Figure 39: HT Physical Mode Settings 75 Figure 40: Advanced Wireless Settings 77 Figure 41: Wi-Fi Multimedia Settings 79 Figure 42: WMM Configuration 80 Figure 43: Multicast-to-Unicast Converter 81 Figu
FIGURES Figure 68: Statistics 114 Figure 69: System Log 115 Figure 70: 3G Budget Status 116 Figure 71: RJ-45 Connector 124 Figure 72: Straight-through Wiring 126 Figure 73: Crossover Wiring 126 – 17 –
TABLES Table 1: Key Hardware Features 20 Table 2: LED Behavior 24 Table 3: WMM Access Categories 79 Table 4: LED Indicators 120 Table 5: 10/100BASE-TX MDI and MDI-X Port Pinouts 125 – 18 –
SECTION I GETTING STARTED This section provides an overview of the Mini 3G Broadband Router, and describes how to install and mount the unit. It also describes the basic settings required to access the management interface and run the setup Wizard.
1 INTRODUCTION The Barricade 150Mbps Wireless-N Mini 3G Broadband Router (SMCWBR11S-3GN) supports routing from an Internet Service Provider (ISP) connection (DSL or cable modem) to a local network. It is simple to configure and can be up and running in minutes. KEY HARDWARE FEATURES The following table describes the main hardware features of the Mini 3G Broadband Router. Table 1: Key Hardware Features Feature Description WAN Port One 100BASE-TX RJ-45 port for connecting to the Internet.
CHAPTER 1 | Introduction Description of Capabilities ◆ User-definable application sensing tunnel supports applications requiring multiple connections. ◆ Easy setup and management through an easy-to-use web browser interface on any operating system that supports TCP/IP. ◆ Compatible with all popular Internet applications.
CHAPTER 1 | Introduction Package Contents data network). The VPN-passthrough protocols supported by the Barricade are briefly described below. ■ ■ ■ IPsec (Internet Protocol Security) — Encrypts and authenticates entire IP packets and encapsulates them into new IP packets for secure communications between networks. PPTP (Point-to-Point Tunneling Protocol) — Provides a secure tunnel for remote client access to a PPTP security gateway.
CHAPTER 1 | Introduction Hardware Description Figure 1: Top Panel WPS Button 3G USB Port LED Indicators Figure 2: Rear Panel RJ-45 WAN Port RJ-45 LAN Port – 23 – DC Power Socket
CHAPTER 1 | Introduction Hardware Description LED INDICATORS The Mini 3G Broadband Router includes four status LED indicators, as described in the following figure and table. Figure 3: LEDs WPS SET WLAN LAN WLAN LAN 3G USB WAN 3G USB Power WAN Power Table 2: LED Behavior LED Status Description Power On Blue The unit is receiving power and is operating normally. Off There is no power currently being supplied to the unit. On/Blinking Blue The 802.
CHAPTER 1 | Introduction Hardware Description ETHERNET WAN PORT A 100BASE-TX RJ-45 port that can be attached to an Internet access device, such as a DSL or Cable modem. ETHERNET LAN PORT The Mini 3G Broadband Router has one 100BASE-TX RJ-45 port that can be attached directly to a PC or 10BASE-T/100BASE-TX LAN segments. This port supports automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs, switches, or hubs.
2 NETWORK PLANNING The Mini 3G Broadband Router is designed to be very flexible in its deployment options. It can be used as an Internet gateway for a small network, or as an access point to extend an existing wired network to support wireless users. It also supports use as a wireless bridge to connect up to four wired LANs. This chapter explains some of the basic features of the Mini 3G Broadband Router and shows some network topology examples in which the device is implemented.
CHAPTER 2 | Network Planning LAN Access Point The private local network, connected to the LAN port or wireless interface, provides a Dynamic Host Configuration Protocol (DHCP) server for allocating IP addresses to local PCs and wireless clients, and Network Address Translation (NAT) for mapping the multiple "internal" IP addresses to one “external” IP address.
CHAPTER 2 | Network Planning Wireless Bridge WIRELESS BRIDGE The IEEE 802.11 standard defines a Wireless Distribution System (WDS) for bridge connections between access points. The Mini 3G Broadband Router can use WDS to forward traffic on links between units. Up to four WDS links can be specified for the Mini 3G Broadband Router. The WDS feature enables two basic functions to be configured in the wireless network.
3 INSTALLING THE MINI 3G ROUTER The Mini 3G Broadband Router has two basic operating modes that can be set through the web-based management interface. For information on setting the mode suitable for your network environment. See “Operation Mode” on page 53. ◆ Router Mode — A gateway mode that connects a wired LAN and wireless clients to an Internet access device, such as a cable or DSL modem. This is the factory set default mode.
CHAPTER 3 | Installing the Mini 3G Router Mounting the Device MOUNTING THE DEVICE The Mini 3G Broadband Router can be mounted on any horizontal surface, or on a wall. The following sections describe the mounting options. MOUNTING ON A WALL The Mini 3G Broadband Router should be mounted only to a wall or wood surface that is at least 1/2-inch plywood or its equivalent. To mount the unit on a wall, always use its wall-mounting slots.
CHAPTER 3 | Installing the Mini 3G Router Router Mode Connections ROUTER MODE CONNECTIONS In its default Router Mode, the Mini 3G Broadband Router forwards traffic between an Internet connected cable or DSL modem, and wired or wireless PCs or notebooks. The basic connections are illustrated in the figure below. Figure 10: Router Mode Connection up wireless 4. Set devices Notebook PC Internet WAN port to 1. Connect cable/DSL modem AC power 3. Connect adapter to power source Cable/DSL Modem LAN port 2.
CHAPTER 3 | Installing the Mini 3G Router Bridge Mode Connections BRIDGE MODE CONNECTIONS In Bridge Mode, the Mini 3G Broadband Router operates as a wireless access point, extending a local wired network to associated wireless clients (PCs or notebooks with wireless capability). From any nearby location, you can then make a wireless connection to the Mini 3G Broadband Router and access the wired network resources, including local servers and the Internet.
CHAPTER 3 | Installing the Mini 3G Router Bridge Mode Connections 3. Set up wireless devices by pressing the WPS button on the Mini 3G Broadband Router or by using the web interface. See “Initial Configuration” on page 34 for more information on accessing the web interface.
4 INITIAL CONFIGURATION The Mini 3G Broadband Router offers a user-friendly web-based management interface for the configuration of all the unit’s features. Any PC directly attached to the unit can access the management interface using a web browser, such as Internet Explorer (version 6.0 or above). ISP SETTINGS If you are not sure of your connection method, please contact your Internet Service Provider.
CHAPTER 4 | Initial Configuration Home Page and Main Menu Figure 12: Login Page HOME PAGE AND MAIN MENU After logging in to the web interface, the Home page displays. The Home page shows the main menu and the method to access the Setup Wizard.
CHAPTER 4 | Initial Configuration Common Web Page Buttons COMMON WEB PAGE BUTTONS The list below describes the common buttons found on most web management pages: ◆ Apply – Applies the new parameters and saves them to memory. Also displays a screen to inform you when it has taken affect. Clicking ‘Apply’ returns to the home page. ◆ Cancel – Cancels the newly entered settings and restores the previous settings. ◆ Next – Proceeds to the next step. ◆ Previous – Returns to the previous screen.
CHAPTER 4 | Initial Configuration Setup Wizard STEP 2 - TIME The Step 2 page of the Wizard configures time zone and SNTP settings. SETTINGS Select a time zone according to where the device is operated. Click Next after completing the setup. Figure 15: Wizard Step 2 - Time and SNTP Settings The following items are displayed on this page: ◆ Current Time — Receives a time and date stamp from an SNTP server. ◆ Sync with host — Updates the unit's time from the web management PC's system time.
CHAPTER 4 | Initial Configuration Setup Wizard Figure 16: Wizard Step 3 - WAN Settings - DHCP The following items are displayed on this page: ◆ Ethernet Port — Select “Cable/Dynamic IP (DHCP)” for the WAN port connection from the drop-down list. (Default: DHCP) ■ Enable MAC Clone — Some ISPs limit Internet connections to a specified MAC address of one PC, which is registered with the ISP.
CHAPTER 4 | Initial Configuration Setup Wizard addresses. To specify a DNS server, type the IP addresses in the text field provided. Otherwise, leave the text field blank. ◆ Secondary DNS Server — The IP address of the Secondary Domain Name Server. STEP 3 - WAN Configures a static IP for the WAN port.
CHAPTER 4 | Initial Configuration Setup Wizard ◆ Default Gateway — The IP address of the gateway router for the Mini 3G Broadband Router, which is used if the requested destination address is not on the local subnet. ◆ Primary DNS Server — The IP address of the Primary Domain Name Server. A DNS maps numerical IP addresses to domain names and can be used to identify network hosts by familiar names instead of the IP addresses. To specify a DNS server, type the IP addresses in the text field provided.
CHAPTER 4 | Initial Configuration Setup Wizard ◆ USB Port — Enables support for a WAN connection using a USB 3G modem. For more information, see “Step 3 - WAN Settings - 3G” on page 45. (Default: Disabled) ◆ User Name — Sets the PPPoE user name for the WAN port. (Default: pppoe_user; Range: 1~32 characters) ◆ Password — Sets a PPPoE password for the WAN port. (Default: pppoe_password; Range: 1~32 characters) ◆ Verify Password — Prompts you to re-enter your chosen password.
CHAPTER 4 | Initial Configuration Setup Wizard the MAC address of the Mini 3G Broadband Router's WAN interface to match the PC's MAC address provided to your ISP for registration. You can enter the registered MAC address manually by typing it in the boxes provided. Otherwise, connect only the PC with the registered MAC address to the Mini 3G Broadband Router, then click the “Clone your PC’s MAC Address.” (Default: Disable) ◆ USB Port — Enables support for a WAN connection using a USB 3G modem.
CHAPTER 4 | Initial Configuration Setup Wizard STEP 3 - WAN Enables the Layer 2 Tunneling Protocol (L2TP) for implementing virtual SETTINGS - L2TP private networks. The service is provided in many European countries. Figure 20: Wizard Step 3 - WAN Settings - L2TP The following items are displayed on this page: ◆ Ethernet Port — Select “L2TP” for the WAN port connection from the drop-down list. ■ Enable MAC Clone — Some ISPs limit Internet connections to a specified MAC address.
CHAPTER 4 | Initial Configuration Setup Wizard ◆ Verify Password — Prompts you to re-enter your chosen password. ◆ Address Mode — Sets a L2TP network mode. (Default: Dynamic) ◆ IP Address — Sets the static IP address. (Default: 0.0.0.0, available when L2TP Network Mode is set to static IP.) ◆ Subnet Mask — Sets the static IP subnet mask. (Default: 255.255.255.0, available when L2TP Network Mode is set to static IP.
CHAPTER 4 | Initial Configuration Setup Wizard STEP 3 - WAN Enables support for a USB 3G modem as a WAN connection, either as a SETTINGS - 3G primary (Master) link, or as a backup to the WAN port link. Figure 21: Wizard Step 3 - WAN Settings - 3G The following items are displayed on this page: ◆ Ethernet Port — Select the WAN port connection type from the dropdown list. Alternatively, you can disable the Ethernet WAN port connection and just use the USB 3G modem connection.
CHAPTER 4 | Initial Configuration Setup Wizard ◆ USB Port — Enables support for a WAN connection using a USB 3G modem. When enabled, you can select if the 3G modem connection operates as the Master or Backup WAN link. (Default: Disabled) ■ ■ ◆ Master WAN — Enables the USB 3G modem WAN connection to operate as the primary WAN link. The Ethernet WAN port then operates as the backup link.
CHAPTER 4 | Initial Configuration Setup Wizard ◆ Password — The password of the account registered with the 3G or 3.5G service provider. ◆ Budget Control — Enables a monthly limit on time or total data. For more information, see “3G” on page 62. (Default: Disabled) STEP 4 - WIRELESS The Step 4 page of the Wizard configures the wireless network name and SECURITY security options.
CHAPTER 4 | Initial Configuration Setup Wizard known wireless devices that may not be able to support the configured security mode. ◆ Add a station MAC — Enter the MAC address of the station that you want to filter. MAC addresses must be entered in the format xx:xx:xx:xx:xx:xx. COMPLETION After completion of the Wizard, the screen returns to the Home Page.
SECTION II WEB CONFIGURATION This section provides details on configuring the Mini 3G Broadband Router using the web browser interface.
5 OPERATION MODE The Mini 3G Broadband Router offers a user-friendly web-based management interface for the configuration of all the unit’s features. Any PC directly attached to the unit can access the management interface using a web browser, such as Internet Explorer (version 6.0 or above).
CHAPTER 5 | Operation Mode Logging In LOGGING IN It is recommended to make initial configuration changes by connecting a PC directly to the Mini 3G Broadband Router's LAN port. The Mini 3G Broadband Router has a default IP address of 192.168.2.1 and a subnet mask of 255.255.255.0. If your PC is set to “Obtain an IP address automatically” (that is, set as a DHCP client), you can connect immediately to the web interface.
CHAPTER 5 | Operation Mode Logging In The home page displays the main menu items at the top of the screen and the Setup Wizard. See “Setup Wizard” on page 36. Figure 24: Home Page NOTE: The displayed pages and settings may differ depending on whether the unit is in Router or Bridge Mode. See “Operation Mode” on page 53.
CHAPTER 5 | Operation Mode Operation Mode OPERATION MODE The Operation Mode Configuration page allows you to set up the mode suitable for your network environment. Figure 25: Operation Mode The following items are displayed on this page: ◆ Bridge Mode — An access point mode that extends a wired LAN to wireless clients. ◆ Router Mode — The Internet gateway mode that connects a wired LAN and wireless clients to an Internet access device, such as a cable or DSL modem. This is the factory set default mode.
6 NETWORK SETTINGS The Network Settings pages allow you to manage basic system configuration settings.
CHAPTER 6 | Network Settings WAN Setting WAN SETTING The WAN Setting page specifies the Internet connection parameters. Click on “Network Settings” followed by “WAN”. By default, the WAN port is configured with DHCP enabled. The options are Static IP, DHCP (cable modem), PPPoE (DSL modem), PPTP, and L2TP. You can also enable support for a USB 3G modem as a WAN connection, either as a primary (Master) link, or as a backup to the WAN port link.
CHAPTER 6 | Network Settings WAN Setting DHCP Enables Dynamic Host Configuration Protocol (DHCP) for the WAN port. This setting allows the Mini 3G Broadband Router to automatically obtain an IP address from a DHCP server normally operated by the Internet Service Provider (ISP). Figure 26: DHCP Configuration The following items are displayed on this page: ◆ Hostname (Optional) — The hostname of the DHCP client. ◆ Primary DNS Server — The IP address of the Primary Domain Name Server.
CHAPTER 6 | Network Settings WAN Setting STATIC IP Configures a static IP for the WAN port. Figure 27: Static IP Configuration The following items are displayed on this page: ◆ IP Address — The IP address of the Mini 3G Broadband Router. Valid IP addresses consist of four decimal numbers, 0 to 255, separated by periods. ◆ Subnet Mask — The mask that identifies the host address bits used for routing to specific subnets.
CHAPTER 6 | Network Settings WAN Setting PPPOE Enables the Mini 3G Broadband Router IP address to be assigned automatically from an Internet service provider (ISP) through a DSL modem using Point-to-Point Protocol over Ethernet (PPPoE). Figure 28: PPPoE Configuration The following items are displayed on this page: ◆ PPPoE User Name — Sets the PPPoE user name for the WAN port. (Default: pppoe_user; Range: 1~32 characters) ◆ PPPoE Password — Sets a PPPoE password for the WAN port.
CHAPTER 6 | Network Settings WAN Setting PPTP Enables the Point-to-Point Tunneling Protocol (PPTP) for implementing virtual private networks. The service is provided in many European countries. Figure 29: PPTP Configuration The following items are displayed on this page: ◆ Server IP — Sets a PPTP server IP Address. (Default: pptp_server) ◆ User Name — Sets the PPTP user name for the WAN port. (Default: pptp_user; Range: 1~32 characters) ◆ Password — Sets a PPTP password for the WAN port.
CHAPTER 6 | Network Settings WAN Setting ◆ Subnet Mask — Sets the static IP subnet mask. (Default: 255.255.255.0, available when PPTP Network Mode is set to static IP.) ◆ Default Gateway — The IP address of the gateway router for the Mini 3G Broadband Router, which is used if the requested destination address is not on the local subnet. ◆ Operation Mode — Selects the operation mode as Keep Alive, or Manual.
CHAPTER 6 | Network Settings WAN Setting L2TP Enables the Layer 2 Tunneling Protocol (L2TP) for implementing virtual private networks. The service is provided in many European countries. Figure 30: L2TP Configuration The following items are displayed on this page: ◆ Server IP — Sets the L2TP server IP Address. (Default: l2tp_server) ◆ User Name — Sets the L2TP user name for the WAN port. (Default: l2tp_user; Range: 1~32 characters) ◆ Password — Sets a L2TP password for the WAN port.
CHAPTER 6 | Network Settings WAN Setting ◆ Default Gateway — The IP address of the gateway router for the Mini 3G Broadband Router, which is used if the requested destination address is not on the local subnet. ◆ Operation Mode — Selects the operation mode as Keep Alive, or Manual. (Default: Keep Alive) ■ ■ Keep Alive Mode: The Mini 3G Broadband Router will periodically check your Internet connection and automatically re-establish your connection when disconnected.
CHAPTER 6 | Network Settings WAN Setting ■ ◆ Backup WAN — Enables the USB 3G modem WAN connection to operate as the backup to the Ethernet WAN port link. (Default: Enabled) Dual WAN Mode — When both the WAN port and 3G modem connections are enabled, you can configure the following parameters: ■ Fallback of Dual WAN — The operation of the fallback between dual WAN connections is as follows: (Default: Disabled) ■ ■ Enable — The Master WAN connection is used first.
CHAPTER 6 | Network Settings WAN Setting code is not required for your 3G or 3.5G modem, disable this function. (Default: Disabled) ◆ Dial Code — A dialled access code that connects the USB device to the service provider. ◆ APN Service — The access point name (APN) that uniquely identifies the 3G or 3.5G service provider. ◆ User Name — The user name of the account registered with the 3G or 3.5G service provider. ◆ Password — The password of the account registered with the 3G or 3.
CHAPTER 6 | Network Settings WAN Setting ◆ Budget Policy — Specifies the action to take when budget limits have been reached. ■ Action if Over Budget — Specifies the the action to take when a budget limit has been exceeded: ■ ■ ■ ◆ Drop Current Connection — Immediately drop the current connection. (Default: Enabled) Disallow New Connection — Do not permit any new connections.
CHAPTER 6 | Network Settings LAN Setting ■ Mail Recipient — The E-mail address of the recipient of the alert messages. LAN SETTING The Mini 3G Broadband Router must have a valid IP address for management using a web browser and to support other features. The unit has a default IP address of 192.168.2.1. You can use this IP address or assign another address that is compatible with your existing local network. Click on “Network Settings” followed by “LAN.
CHAPTER 6 | Network Settings LAN Setting ◆ Subnet Mask — Indicate the local subnet mask. (Default: 255.255.255.0.) ◆ DHCP Server — Enable this feature to assign IP settings to wired and wireless clients connected to the Mini 3G Broadband Router. The IP address, subnet mask, default gateway, and Domain Name Server (DNS) address are dynamically assigned to clients.
CHAPTER 6 | Network Settings DHCP Clients DHCP CLIENTS The DHCP Clients page displays information on connected client stations that have been assigned IP addresses from the DHCP address pool. Figure 36: DHCP Clients The following items are displayed on this page: Host name — The name of the connected client station. MAC Address — The MAC address of the connected client station. IP Address — The IP address assigned to the client from the IP pool.
CHAPTER 6 | Network Settings Advanced Routing ADVANCED ROUTING Routing setup allows a manual method to set up routing between networks. The network administrator configures static routes by entering routes directly into the routing table. Static routing has the advantage of being predictable and easy to configure. ADVANCED ROUTING This screen is used to manually configure static routes to other IP SETTINGS networks, subnetworks, or hosts. Click “Network Settings” followed by “Advanced Routing.
CHAPTER 6 | Network Settings Advanced Routing The following items are displayed on this page: ◆ Destination — A destination network or specific host to which packets can be routed. ◆ Type — Defines the type of destination. (Options: Host/Net, Default: Host) ◆ Gateway — The IP address of the router at the next hop to which matching frames are forwarded. ◆ Interface — The selected interface to which a static routing subnet is to be applied.
CHAPTER 6 | Network Settings Advanced Routing ◆ Ref — Number of references to this route. ◆ Use — Count of lookups for the route. ◆ Interface — Interface to which packets for this route will be sent. ◆ Comment — Displays a useful comment to identify the routing rules. DYNAMIC ROUTE ◆ The Mini 3G Broadband Router supports RIP 1 and RIP 2 dynamic routing protocol. Routing Information Protocol (RIP) is the most widely used method for dynamically maintaining routing tables.
7 WIRELESS CONFIGURATION The wireless settings section displays configuration settings for the access point functionality of the Mini 3G Broadband Router. It includes the following sections: ◆ “Basic Settings” on page 72 ◆ “Advanced Settings” on page 76 ◆ “WLAN Security” on page 82 ◆ “Wireless Distribution System (WDS)” on page 89 ◆ “Wi-Fi Protected Setup (WPS)” on page 92 ◆ “Station List” on page 95 BASIC SETTINGS The IEEE 802.
CHAPTER 7 | Wireless Configuration Basic Settings The Basic Settings page allows you to configure the wireless network name (Service Set Identifier or SSID) and set the wireless security method. Click on “Wireless Settings,” followed by “Basic.” Figure 38: Basic Settings The following items are displayed on this page: ◆ Wireless On/Off — Enables or Disable the radio. (Default: Enable) ◆ Network Mode — Defines the radio operating mode. (Default: 11b/g/n Mixed) ■ 11b/g mixed: Both 802.11b and 802.
CHAPTER 7 | Wireless Configuration Basic Settings ■ ■ ■ 11n only: Only 802.11n clients will be able to communicate with the Mini 3G Broadband Router (up to 150 Mbps). 11g/n mixed: Both 802.11g and 802.11n clients can communicate with the Mini 3G Broadband Router (up to 150 Mbps), but data transmission rates may be slowed to compensate for 802.11g clients. 11b/g/n Mixed: All 802.
CHAPTER 7 | Wireless Configuration Basic Settings HT PHYSICAL MODE The HT Physical Mode section on the Wireless Settings Advanced page SETTINGS includes additional parameters for 802.11n operation. Figure 39: HT Physical Mode Settings The following items are displayed in this section on this page: ◆ HT Channel Bandwidth — The Mini 3G Broadband Router provides a channel bandwidth of 40 MHz by default giving an 802.11g connection speed of 108 Mbps (sometimes referred to as Turbo Mode) and a 802.
CHAPTER 7 | Wireless Configuration Advanced Settings ◆ Space Time Block Coding (STBC) — A mechanism that allows a unit with only one antenna to leverage multiple antennas on other 802.11n devices to improve performance and range. (Default: Enabled) ◆ Extension Channel — When 20/40MHz channel bandwidth has been set, the extension channel option will be enabled. The extension channel will allow you to get extra bandwidth. (Default: AutoSelect.
CHAPTER 7 | Wireless Configuration Advanced Settings ADVANCED WIRELESS The Advanced Wireless section on the Wireless Settings Advanced page includes additional radio parameters. Figure 40: Advanced Wireless Settings The following items are displayed in this section on this page: ◆ BG Protection Mode — Enables a backward compatible protection mechanism for 802.11b clients. There are three modes: (Default: Auto) ■ ■ ■ Auto — The unit enables its protection mechanism for 802.
CHAPTER 7 | Wireless Configuration Advanced Settings will save all broadcast/multicast frames for the Basic Service Set (BSS) and forward them after every beacon. Using smaller DTIM intervals delivers broadcast/multicast frames in a more timely manner, causing stations in Power Save mode to wake up more often and drain power faster. Using higher DTIM values reduces the power used by stations in Power Save mode, but delays the transmission of broadcast/multicast frames.
CHAPTER 7 | Wireless Configuration Advanced Settings ◆ TX Burst — A performance enhancement that transmits a number of data packets at the same time when the feature is supported by compatible clients. (Default: Enabled) ◆ Packet Aggregate — A performance enhancement that combines data packets together when the feature is supported by compatible clients. (Default: Enabled) WI-FI MULTIMEDIA The Mini 3G Broadband Router implements Quality of Service (QoS) using the Wi-Fi Multimedia (WMM) standard.
CHAPTER 7 | Wireless Configuration Advanced Settings The following items are displayed in this section on this page: ◆ WMM — Sets the WMM operational mode on the access point. When enabled, the QoS capabilities are advertised to WMM-enabled clients in the network. WMM must be supported on any device trying to associated with the access point. Devices that do not support this feature will not be allowed to associate with the access point.
CHAPTER 7 | Wireless Configuration Advanced Settings microseconds. Note that the CWMin value must be equal or less than the CWMax value. ◆ CWMax (Maximum Contention Window) — The maximum upper limit of the random backoff wait time before wireless medium access can be attempted. The contention window is doubled after each detected collision up to the CWMax value. Specify the CWMax value in the range 0-15 microseconds. Note that the CWMax value must be greater or equal to the CWMin value.
CHAPTER 7 | Wireless Configuration WLAN Security WLAN SECURITY The Mini 3G Broadband Router’s wireless interface is configured by default as an “open system,” which broadcasts a beacon signal including the configured SSID. Wireless clients with a configured SSID of “ANY” can read the SSID from the beacon, and automatically set their SSID to allow immediate connection to the wireless network.
CHAPTER 7 | Wireless Configuration WLAN Security The supported security mechanisms and their configuration parameters are described in the following sections: ◆ OPEN, SHARED, WEP-AUTO — See “Wired Equivalent Privacy (WEP)” on page 83 ◆ WPA-PSK, WPA2-PSK, WPA-PSK_WPA2-PSK — See “WPA PreShared Key” on page 84 ◆ WPA, WPA2, WPA1_WPA2 — See “WPA Enterprise Mode” on page 85 ◆ 802.1X — See “IEEE 802.
CHAPTER 7 | Wireless Configuration WLAN Security ◆ WEP-AUTO — Allows wireless clients to connect to the network using Open-WEP (uses WEP for encryption only) or Shared-WEP (uses WEP for authentication and encryption). ◆ Encrypt Type — Selects WEP for data encryption (OPEN mode only). ◆ Default Key — Selects the WEP key number to use for authentication or data encryption.
CHAPTER 7 | Wireless Configuration WLAN Security ◆ WPA-PSK — Clients using WPA with a Pre-shared Key are accepted for authentication. The default data encryption type for WPA is TKIP. ◆ WPA2-PSK — Clients using WPA2 with a Pre-shared Key are accepted for authentication. The default data encryption type for WPA is AES. ◆ WPA-PSK_WPA2-PSK — Clients using WPA or WPA2 with a Preshared Key are accepted for authentication. The default data encryption type is TKIP/AES.
CHAPTER 7 | Wireless Configuration WLAN Security Figure 47: Security Mode - WPA The following items are displayed in this section on this page: Security Mode — Configures the WPA and WPA2 security modes used by clients. When using WPA or WPA2, be sure there is a RADIUS server in the connected wired network, and that the RADIUS settings are configured. See “IEEE 802.1X and RADIUS” on page 87 for more information. (Default: Disable) ◆ WPA — Clients using WPA with an 802.
CHAPTER 7 | Wireless Configuration WLAN Security message integrity. The AES Counter-Mode/CBCMAC Protocol (AESCCMP) provides extremely robust data confidentiality using a 128bit key. Use of AES-CCMP encryption is specified as a standard requirement for WPA2. Before implementing WPA2 in the network, be sure client devices are upgraded to WPA2-compliant hardware. ■ TKIP/AES — Uses either TKIP or AES keys for encryption. WPA and WPA2 mixed modes allow both WPA and WPA2 clients to associate to a common SSID.
CHAPTER 7 | Wireless Configuration WLAN Security Figure 48: Security Mode - 802.1X The following items are displayed in this section on this page: Security Mode — Configures the 802.1X security mode used by clients. When using 802.1X, either with WPA/WPA2 or on its own, be sure there is a configured RADIUS server in the connected wired network. (Default: Disable) 802.1X WEP: Selects WEP keys for data encryption.
CHAPTER 7 | Wireless Configuration Wireless Distribution System (WDS) ACCESS POLICY The Mini 3G Broadband Router provides a MAC address filtering facility. The access policy can be set to allow or reject specific station MAC addresses. This feature can be used to connect known wireless devices that may not be able to support the configured security mode.
CHAPTER 7 | Wireless Configuration Wireless Distribution System (WDS) Figure 50: Manual WDS MAC Address Configuration Internet Service Provider WDS Link Cable/DSL Modem S WD L ink WD SL MAC: 00-22-2D-62-EA-11 WDS MAC List: 00-22-2D-62-EA-22 00-22-2D-62-EA-33 00-22-2D-62-EA-44 MAC: 00-22-2D-62-EA-44 WDS MAC List: 00-22-2D-62-EA-11 ink MAC: 00-22-2D-62-EA-22 WDS MAC List: 00-22-2D-62-EA-11 MAC: 00-22-2D-62-EA-33 WDS MAC List: 00-22-2D-62-EA-11 Figure 51: WDS Configuration Example Internet Service
CHAPTER 7 | Wireless Configuration Wireless Distribution System (WDS) ◆ Be sure that only one unit has an Internet access on its WAN port. ◆ Be sure the DHCP server is enabled only on one unit. When one unit is providing Internet access, enable the DHCP server on that unit. NOTE: When using WDS Lazy mode in the network, at least one unit must be set to Bridge or Repeater mode. Figure 52: WDS Configuration The WDS settings configure WDS related parameters.
CHAPTER 7 | Wireless Configuration Wi-Fi Protected Setup (WPS) configure a WDS MAC list entry. This feature allows the Mini 3G Broadband Router to associate with other Mini 3G Broadband Routers in the network and use their WDS MAC list. Lazy mode requires one other Mini 3G Broadband Router within the wireless network that is configured in Bridge or Repeater mode, and has a configured MAC address list.
CHAPTER 7 | Wireless Configuration Wi-Fi Protected Setup (WPS) Figure 53: Enabling WPS The following items are displayed on this page: ◆ WPS — Enables WPS, locks security settings, and refreshes WPS configuration information.
CHAPTER 7 | Wireless Configuration Wi-Fi Protected Setup (WPS) The following items are displayed on this page: WPS Summary — Provides detailed WPS statistical information. ◆ WPS Current Status — Displays if there is currently any WPS traffic connecting to the Mini 3G Broadband Router. (Options: Start WSC Process; Idle) ◆ WPS Configured — States if WPS for wireless clients has been configured for this device. ◆ WPS SSID — The service set identifier for the unit.
CHAPTER 7 | Wireless Configuration Station List STATION LIST Displays the station information which associated to this Mini 3G Broadband Router.
8 FIREWALL CONFIGURATION The Mini 3G Broadband Router provides extensive firewall protection by restricting connection parameters to limit the risk of intrusion and defending against a wide array of common hacker attacks.
CHAPTER 8 | Firewall Configuration MAC/IP/Port Filtering Figure 56: MAC/IP/Port Filtering The following items are displayed on this page: ◆ MAC/IP/Port Filtering — Enables or disables MAC/IP/Port Filtering. (Default: Disable) ◆ Default Policy — When MAC/IP/Port Filtering is enabled, the default policy will be enabled. If you set the default policy to “Dropped”, all incoming packets that don’t match the rules will be dropped.
CHAPTER 8 | Firewall Configuration MAC/IP/Port Filtering ◆ Destination IP Address — Specifies the destination IP address to block or allow traffic from. ◆ Source IP Address — Specifies the source IP address to block or allow traffic from. ◆ Protocol — Specifies the destination port type, TCP, UDP or ICMP. (Default: None). ◆ Destination Port Range — Specifies the range of destination port to block traffic from the specified LAN IP address from reaching.
CHAPTER 8 | Firewall Configuration Virtual Server Settings (Port Forwarding) VIRTUAL SERVER SETTINGS (PORT FORWARDING) Virtual Server (sometimes referred to as Port Forwarding) is the act of forwarding traffic from one network node to another based on received protocol port number. This technique can allow an external user to reach a port on a private IP address (inside a LAN) from the outside through a NATenabled router. (Maximum 32 entries are allowed.
CHAPTER 8 | Firewall Configuration Virtual Server Settings (Port Forwarding) ◆ Protocol — Specifies the protocol to forward, either TCP, UDP, or TCP&UDP. ◆ Comment — Enter a useful comment to help identify the port forwarding service on the network. CURRENT VIRTUAL The Current Port Forwarding Table displays the entries that are allowed to SERVERS IN SYSTEM forward packets through the Mini 3G Broadband Router’s firewall. ◆ No. — The table entry number.
CHAPTER 8 | Firewall Configuration DMZ DMZ Enables a specified host PC on the local network to access the Internet without any firewall protection. Some Internet applications, such as interactive games or video conferencing, may not function properly behind the Mini 3G Broadband Router's firewall. By specifying a Demilitarized Zone (DMZ) host, the PC's TCP ports are completely exposed to the Internet, allowing open two-way communication.
CHAPTER 8 | Firewall Configuration System Security SYSTEM SECURITY The Mini 3G Broadband Router includes the facility to manage it from a remote location. The unit can also be sent a ping message from a remote location. Figure 59: System Security The following items are displayed on this page: ◆ Remote Management — Denies or allows management access to the Mini 3G Broadband Router through the WAN interface.
CHAPTER 8 | Firewall Configuration Content Filtering CONTENT FILTERING The Mini 3G Broadband Router provides a variety of options for blocking Internet access based on content, URL and host name. Figure 60: Content Filtering The following items are displayed on this page: Web URL Filter Settings — By filtering inbound Uniform Resource Locators (URLs) the risk of compromising the network can be reduced. URLs are commonly used to point to websites.
CHAPTER 8 | Firewall Configuration Content Filtering and web domains. A domain name is the name of a particular web site. For example, for the address www.FUNGAMES.com, the domain name is FUNGAMES.com. Enter the Keyword then click “Add.” ◆ Current Host Filters — Displays current Host filter. ◆ Add a Host Filter — Enters the keyword for a host filtering.
9 ADMINISTRATION SETTINGS The Mini 3G Broadband Router’s Administration Settings menu provides the same configuration options in both Router and Bridge Mode. These settings allow you to configure a management access password, set the system time, upgrade the system software, display the system status and statistics.
CHAPTER 9 | Administration Settings System Management SYSTEM MANAGEMENT The System Management commands allow you to change the language settings displayed in the interface, and change the user password. Figure 61: System Management The following items are displayed in the first two sections on this page: ◆ Language Settings — You can change the language displayed in web interface. Select the language of your choice from the drop-down list, then click “Apply.
CHAPTER 9 | Administration Settings Time Zone Settings TIME ZONE SETTINGS The System Management page allows you to manually configure time settings or enable the use of a Simple Network Time Protocol (SNTP) or NTP server. Figure 62: Time Zone Settings The following items are displayed in this section on this page: ◆ Current Time — Displays the current system time on the unit. ◆ Sync with host — Updates the unit's time from the web management PC's system time.
CHAPTER 9 | Administration Settings Green AP Settings GREEN AP SETTINGS The Green AP feature can be used for reducing the wireless router’s power consumption. Before setting the Green AP duration, you need to first configure the current time and Time Zone settings. Within the Green AP duration, theWi-Fi radio’s transmit power can be set as reduced, or just turned off. Less transmit power means the wireless router will only cover a shorter range.
CHAPTER 9 | Administration Settings DDNS Settings DDNS SETTINGS Dynamic DNS (DDNS) provides users on the Internet with a method to tie a specific domain name to the unit’s dynamically assigned IP address. DDNS allows your domain name to follow your IP address automatically by changing your DNS records when your IP address changes. The Mini 3G Broadband Router provides access to three DDNS service providers, DynDns.org, Non-IP.com and ZoneEdit.com.
CHAPTER 9 | Administration Settings Firmware Upgrade FIRMWARE UPGRADE You can update the Mini 3G Broadband Router firmware by using the Firmware Update facility. Figure 65: Firmware Upgrade The following items are displayed on this page: ◆ Firmware Upgrade — Allows you to upload new firmware manually by specifying a file path. Make sure the firmware you want to use is on the local computer by clicking Browse to search for the firmware to be used for the update.
CHAPTER 9 | Administration Settings Configuration Settings CONFIGURATION SETTINGS The Configuration Setting page allows you to save the Mini 3G Broadband Router’s current configuration or restore a previously saved configuration back to the device. Figure 66: Configuration Settings The following items are displayed on this page: ◆ Export Settings — Saves the current configuration to a file locally. ◆ Import Settings — Allows the user to load previously saved configuration files from a local source.
CHAPTER 9 | Administration Settings System Status SYSTEM STATUS The System Information page displays basic system information and the displayed settings are for status information only and are not configurable on this page. This information is split into the three sections that follow. Figure 67: System Status (Router Mode) The following items are displayed on this page: ◆ ◆ System Info — Displays the basic system information in both Bridge and Router Modes.
CHAPTER 9 | Administration Settings System Status ■ ■ ■ ■ ◆ Subnet Mask — The mask that identifies the host address bits used for routing to the WAN port. Default Gateway — The default gateway is the IP address of the router for the Mini 3G Broadband Router, which is used if the requested destination address is not on the local subnet. Primary DNS Server / Secondary DNS Server — The IP address of Domain Name Servers.
CHAPTER 9 | Administration Settings Statistics STATISTICS The Mini 3G Broadband Router Traffic Statistics - Interfaces window displays received and transmitted packet statistics for all interfaces on the Mini 3G Broadband Router. Figure 68: Statistics The following items are displayed on this page: ◆ Memory total — The total memory of this Mini 3G Broadband Router. ◆ Memory left — The available memory of this Mini 3G Broadband Router.
CHAPTER 9 | Administration Settings System Log ◆ Tx packets — Displays the total number of packets transmitted by the specified interfaces. ◆ Tx bytes — Displays the total number of bytes transmitted by the specified interface. SYSTEM LOG The Mini 3G Broadband Router supports a logging process that controls error messages saved to memory or sent to a Syslog server. The logged messages serve as a valuable tool for isolating Mini 3G Broadband Router and network problems.
CHAPTER 9 | Administration Settings 3G Budget Status ◆ Clear — Removes the current system log messages from the System Log Table. 3G BUDGET STATUS The 3G Budget Status page displays the current 3G budget status information. The displayed settings are for information only and are not configurable on this page. Parameters on this page are only visible when budget control has been set for the 3G WAN connection.
CHAPTER 9 | Administration Settings 3G Budget Status The following items are displayed on this page: ◆ Budget Control — Displays the current budget control status. ◆ Tme Budget Control — Displays the currect time budget control status. ◆ Max Time Budget/(Percent of Time Pre-limit) — Displays the configured monthly time budget (in hours), and the percentage of the budget (in minutes) at which E-mail alerts are triggered (if enabled).
CHAPTER 9 | Administration Settings 3G Budget Status ■ RCV (MB) — The total current download data. ■ TX (MB) — The total current upload data.
SECTION III APPENDICES This section provides additional information and includes these items: ◆ “Troubleshooting” on page 120 ◆ “Hardware Specifications” on page 122 ◆ “Cables and Pinouts” on page 124 – 119 –
A TROUBLESHOOTING DIAGNOSING LED INDICATORS Table 4: LED Indicators Symptom Action Power and LAN LEDs are off ◆ The AC power adapter may be disconnected. Check connections between the Mini 3G Broadband Router, the power adapter, and the wall outlet. WLAN LED is off ◆ The Mini 3G Broadband Router radio has been disabled through it’s web management interface. Access the management interface using a web browser to enable the radio.
APPENDIX A | Troubleshooting Before Contacting Technical Support BEFORE CONTACTING TECHNICAL SUPPORT Check the following items before you contact local Technical Support. 1. If the Mini 3G Broadband Router cannot be configured using a web browser: ■ ■ ■ Be sure to have configured the Mini 3G Broadband Router with a valid IP address, subnet mask and default gateway.
B HARDWARE SPECIFICATIONS PORT INTERFACES WAN: 10/100BASE-TX port, RJ-45 connector, auto MDI/X (100-ohm, UTP cable; Category 5 or better) LAN: 10/100BASE-TX port, RJ-45 connector, auto MDI/X (100-ohm, UTP cable; Category 5 or better) AC POWER ADAPTER Asian Power Devices Inc. / APD: WA-12112FG, WA-12112R Sunny Electronics Corp.
APPENDIX B | Hardware Specifications DATA RATE 802.11b: 11 / 5.5 / 2 / 1Mbps 802.11g: 54/48/36/24/18/12/9/6 Mbps Draft 802.11n (20MHz, 800ns GI): 65/58.5/52/39/26/19.5/13/6.5 Mbps Draft 802.11n (40MHz, 800ns GI): 135/121.5/108/81/54/40.5/27/ 13.5 Mbps Draft 802.11n (20MHz, 400ns GI): 72.2/65/57.8/43.3/28.9/21.7/14.4/ 7.2 Mbps Draft 802.11n (40MHz, 400ns GI): 150/135/120/90/60/45/30/15 Mbps RF OUTPUT POWER 22.5 +/- 2dBm RADIO FCC Part 15C (Section 15.247) EN 301 489-1 V1.8.1 (2008-04) EN 301 489-17 V1.3.
C CABLES AND PINOUTS TWISTED-PAIR CABLE ASSIGNMENTS For 10/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. For 1000BASE-T connections the twisted-pair cable must have four pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be green and the other, green with white stripes. Also, an RJ-45 connector must be attached to both ends of the cable. NOTE: Each wire pair must be attached to the RJ-45 connectors in a specific orientation.
APPENDIX C | Cables and Pinouts 10/100BASE-TX Pin Assignments 10/100BASE-TX PIN ASSIGNMENTS Use unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for RJ-45 connections: 100-ohm Category 3 or better cable for 10 Mbps connections. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet).
APPENDIX C | Cables and Pinouts Crossover Wiring Figure 72: Straight-through Wiring EIA/TIA 568B RJ-45 Wiring Standard 10/100BASE-TX Straight-through Cable White/Orange Stripe Orange End A White/Green Stripe 1 2 3 4 5 6 7 8 Blue White/Blue Stripe Green White/Brown Stripe 1 2 3 4 5 6 7 8 End B Brown CROSSOVER WIRING If the twisted-pair cable is to join two ports and either both ports are labeled with an “X” (MDI-X) or neither port is labeled with an “X” (MDI), a crossover must be implemented in the
D LICENSE INFORMATION This product includes copyrighted third-party software subject to the terms of the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), or other related free software licenses. The GPL code used in this product is distributed WITHOUT ANY WARRANTY and is subject to the copyrights of one or more authors. For details, refer to the section "The GNU General Public License" below, or refer to the applicable license as included in the source-code archive.
APPENDIX D | License Information The GNU General Public License GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 1. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License.
APPENDIX D | License Information The GNU General Public License a). Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b).
APPENDIX D | License Information The GNU General Public License This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 9.
GLOSSARY 10BASE-T IEEE 802.3-2005 specification for 10 Mbps Ethernet over two pairs of Category 3 or better UTP cable. 100BASE-TX IEEE 802.3-2005 specification for 100 Mbps Fast Ethernet over two pairs of Category 5 or better UTP cable. 1000BASE-T IEEE 802.3ab specification for 1000 Mbps Gigabit Ethernet over four pairs of Category 5 or better UTP cable. ACCESS POINT An internetworking device that seamlessly connects wired and wireless networks.
GLOSSARY the Bootstrap Protocol (BOOTP), adding the capability of automatic allocation of reusable network addresses and additional configuration options. ENCRYPTION Data passing between the access point and clients can use encryption to protect from interception and evesdropping. ETHERNET A popular local area data communications network, which accepts transmission from computers and terminals. FTP File Transfer Protocol: A TCP/IP protocol used for file transfer.
GLOSSARY ODFM Orthogonal Frequency Division Multiplexing: OFDM allows multiple users to transmit in an allocated band by dividing the bandwidth into many narrow bandwidth carriers. SSID Service Set Identifier: An identifier that is attached to packets sent over the wireless LAN and functions as a password for joining a particular radio cell; i.e., Basic Service Set (BSS).
GLOSSARY WPA-PSK WPA Pre-shared Key: WPA-PSK can be used for small office networks with a limited number of users that may not need a high level of security. WPAPSK provides a simple security implementation that uses just a pre-shared password for network access.
INDEX NUMERICS D 10/100BASE-TX pin assignments 125 3G modem port 25 802.11n settings 72 802.
INDEX I O IGMP proxy 67 import configuration 111 indicators, LED 24 information, system 112 Internet connection problems 120 Internet gateway connections 26 IP address, default 34, 51 IP Address, LAN setting 66 IP port filtering 96 IPsec 20, 22 ISP accounts 21 ISP settings 34 open system 82 operation mode, setting K key features 20 L L2TP 22 LAN ports 23, 25 LAN settings 66 language settings 36, 106 Lazy Mode, WDS 91 lease time, DHCP 67 LED indicators 24 troubleshooting 120 license information 127 loc
INDEX slot time 78 slots, wall-mounting 30 SNTP 107 socket, DC power 23 software upgrade 110 specifications, hardware 122 SSID 72, 74 standards, radio 123 stateful packet inspection 102 station list, wireless 95 statistics, system 114 status indicators 24 status of system 112 straight-through cables 125 system capabilities 20 system defaults 111 system log 115 system requirements 29 system time 107 web page buttons 36 web URL filters 103 website host filters 103 WEP security 83 Wi-Fi Multimedia 79 Wi-Fi n
SMCWBR11S-3GN
