EZ Switch 10/100 24/16-Port Fast Ethernet Switch 24/16 auto-MDI/X ports—connect to PCs or other switches or hubs Optional fiber uplink for easy network expansion Plug and play—nothing to configure, no crossover cables required Auto-negotiation of speed and duplex mode Full-duplex support on all ports Half and full-duplex flow control Desktop and rack mountable User Guide SMC-EZ1024FDT SMC-EZ1016FDT
EZ Switch 10/100 User Guide From SMC’s EZ line of low-cost workgroup LAN solutions 6 Hughes Irvine, CA 92618 Phone: (949) 707-2400 March 2001 Pub.
Copyright Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright © 2001 by SMC Networks, Inc. 6 Hughes, Irvine, CA. All rights reserved.
LIMITED WARRANTY Limited Warranty Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller.
LIMITED WARRANTY OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS.
COMPLIANCES FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications.
COMPLIANCES Industry Canada - Class A This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of Industry Canada. Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe A prescrites dans la norme sur le matérial brouilleur: “Appareils Numériques”, NMB-003 édictée par l’Industrie.
COMPLIANCES Wichtige Sicherheitshinweise (Germany) 1. Bitte lesen Sie diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine Flüssigoder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung. 4. Die Netzanschlu ßsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6.
COMPLIANCES iv
TABLE OF CONTENTS TABLE CONTENTS OF About the EZ Switch 10/100 . . . . . . . . . . . . . . . . . .1 Features and Benefits . . . . . . . . . Front Panel LEDs . . . . . . . . . . . . Rear Panel . . . . . . . . . . . . . . . . . Connecting to a Fiber Optic Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 4 5 Installing the Switch . . . . .
TABLE OF CONTENTS ii
ABOUT THE ABOUT THE EZ SWITCH 10/100 The EZ Switch 10/100 SMC-EZ1024FDT and SMC-EZ1016FDT are 24/16-port Fast Ethernet switches. They have one slot on the rear panel for a fiber optic uplink module with one 100BASE-FX (SC, ST, MTRJ or VF-45) type port. The 10BASE-T/100BASE-TX ports deliver dedicated 10/100 Mbps links to each attached LAN segment. Each port on each switch supports automatic MDI/MDI-X detection.
EZ SWITCH 10/100 Features and Benefits ◆ Auto configuration for MDI/MDI-X cable connection allows connections to servers, workstations, hubs or switches to be made with straight-through cabling ◆ Optional multimode and single-mode fiber uplink modules ◆ Auto-negotiation of half or full duplex on all ports ◆ IEEE 802.3 and 802.
EZ SWITCH 10/100 Front Panel LEDs The front panel of the switch provides status LEDs for “at-a-glance” system monitoring. The following table details the functions of the various indicators: Port and System Status LEDs LED Condition Status Power On The switch is receiving power. RJ-45 Ports Link/ Act 100M FDX On The port has established a valid network connection. Flashing Traffic is passing through the port. Off The port has not established any network connection.
EZ SWITCH 10/100 Port and System Status LEDs LED Condition Status Module Ports Link/ Act On The module has established a valid network connection. Flashing Traffic is passing through the module. Off The module has not established any network connection. Note: All optional modules operate in full-duplex mode only. Rear Panel The AC power receptacle is located on the rear panel of the switch.
EZ SWITCH 10/100 Connecting to a Fiber Optic Port The fiber modules are shown in the figure below. When you connect fiber cable to a 100 Mbps module on the switch, be sure you use an SC, ST, MTRJ or VF-45 type connector, depending on the module. When inserting the cable, be sure the tab on the plug clicks into position to ensure that it is properly seated. For ST-type connections run cable from the Rx (Tx) port on the module to the Tx (Rx) port on the target device.
EZ SWITCH 10/100 The fiber module operates at 100 Mbps, full duplex, and supports 1EEE 802.3x flow control. The maximum length for 100BASE-FX fiber is as shown in the following table. 6 Fiber transceiver Optical Wavelength Maximum Cable Length Multimode 1300 nm 2 km (1.24 miles) Single-mode 1300 nm 20 km (12.
INSTALLING THE SWITCH INSTALLING THE SWITCH The EZ Switch 10/100 can be placed on a desktop or shelf, or installed in a standard 19-inch equipment rack.
INSTALLING THE SWITCH 8 Before rack mounting the switch, pay particular attention to the following factors: • Temperature: Since the temperature within a rack assembly may be higher than the ambient room temperature, check that the rack-environment temperature is within the specified operating temperature range. • Mechanical Loading: Do not place any equipment on top of a rack-mounted switch. • Circuit Overloading: Be sure that the supply circuit to the rack assembly is not overloaded.
INSTALLING THE SWITCH Instructions 1. Positioning the Switch: For desktop or shelf mounting, attach the four adhesive feet to the bottom of the switch. For rack-mounting, attach the mounting brackets on both sides of the switch with the screws provided, and install the switch in the rack.
INSTALLING THE SWITCH 2. Applying Power: Plug one end of the power cable into the power receptacle at the back of the switch, and the other end into an appropriate electrical outlet. Check the Power LED to be sure power is on. Note: It is not necessary to power off the switch before connecting or disconnecting any UTP cables, as these actions will not disrupt the operation of other devices attached to the switch. 3.
INSTALLING THE SWITCH Sample Applications In the figure below, the EZSwitch 10/100 is operating as a collapsed backbone for a small LAN. It is providing dedicated 20 Mbps full-duplex connections to workstations and 200 Mbps full-duplex connections to power users and servers.
TROUBLESHOOTING TROUBLESHOOTING 1. Symptom Power LED does not light after power on. Probable Causes Power outlet or power cord may be defective. Possible Solutions • Check for loose connections. • Check the power outlet by using it for another device. • Replace the power cord. 2. Symptom Link LED does not light after connection is made. Probable Causes Switch port, network card or cable may be defective. Possible Solutions • Check that the switch and attached device are both powered on.
CABLES CABLES CABLE SPECIFICATION Cable Types and Specifications Cable Type Max. Length Connector 10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45 100BASE-TX Cat. 5 100-ohm UTP 100 m (328 ft) RJ-45 100BASE-FX 50/125 or 62.5/125 micron 2 km multimode fiber optic cable (1.24 miles) SC, ST, MTRJ or VF-45 100BASE-FX 9/125 micron single-mode 20 km fiber optic cable (12.43 miles) SC, ST or MTRJ Note: If you need to connect from an SC connector to a device with 62.
CABLES RJ-45 Connector Pin Assignments Caution: DO NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards. An Ethernet or Fast Ethernet twisted-pair link segment requires two pairs of wires. Each wire pair is identified by two different colors. Each wire pair must be attached to the RJ-45 connector in a specific orientation detailed below.
SPECIFICATIONS SPECIFICATIONS EZ SWITCH 10/100 Models SMC-EZ1024FDT SMC-EZ1016FDT Ports SMC-EZ1024FDT - 24 RJ-45 ports SMC-EZ1016FDT - 16 RJ-45 ports Network Interface RJ-45: 100 ohm, UTP cable 10BASE-T - Categories 3, 4, or 5 100BASE-TX - Category 5 LEDs Power - one Link/Act (activity) - one per port 100M - one per port FDX (full duplex) - one per port Switching Method Store-and-forward MAC Address Table 4K entries per system Memory Buffer 768 KBytes per unit Filtering/Forwarding/Learning Rates Full line
SPECIFICATIONS Size 17.32 x 6.81 x 1.69 in. (44.0 x 17.3 x 4.3 cm) Weight SMC-EZ1024FDT 5.3 lbs (2.3 kg) SMC-EZ1016FDT 4.8 lbs (2.2 kg) Temperature Operating: 32 to 122 °F (0 to 50 °C) Storage: -40 to 158 °F (-40 to 70 °C) Humidity, non-condensing 5% to 95% Power Requirements Universal AC input; 100 to 240 VAC, 50 to 60 Hz Power Consumption 40 Watts maximum Heat Dissipation 137 BTU/hr maximum @100 - 240 VAC Maximum Current 0.3 A @ 115 VAC 0.15 A @ 240 VAC Standards IEEE 802.3 IEEE 802.3u IEEE 802.
SPECIFICATIONS TÜV/GS (EN60950) Warranty Limited Lifetime Fiber Uplink Modules Models SMC-EZ108FMSC, SMC-EZ108FSSC, SMC-EZ108FMST, SMC-EZ108FSST, SMC-EZ108FMMT, SMC-EZ108FMMT, SMC-EZ108FMVF Access Method CSMA/CD Communication Rate 100 Mbps Communication Mode Full and half duplex (via jumper setting) Network Interface SC, ST or MTRJ connector, 50/125 or 62.5/125 micron multimode fiber cable. 9/125 micron single mode fiber cable. VH-45 connector, 50/125 or 62.5/125 micron multimode fiber cable.
SPECIFICATIONS 18
FOR TECHNICAL SUPPORT, CALL: From U.S.A. and Canada (24 hours, 7 days a week) (800) SMC-4-YOU; (949) 707-2400; (949) 707-2460 (Fax) From Europe (8:00 AM - 5:30 PM UK Greenwich Mean Time) 44 (0) 1188 748740; 44 (0) 1189 748741 (Fax) INTERNET E-mail address: techsupport@smc.com european.techsupport@smc-europe.com Driver updates: http://www.smc.com/support.html World Wide Web: http://www.smc.com/ FTP Site: ftp.smc.com FOR LITERATURE OR ADVERTISING RESPONSE, CALL: U.S.A.
