Owner's manual

ManualsBrandsSMC Networks ManualsComputer Accessories10/100

TigerSwitch 10/100

16-Port Fast Ethernet Switch

◆ 16 10BASE-T/100BASE-TX ports

◆ Optional 1000BASE-X or 100BASE-FX modules

◆ 8.8 Gbps of aggregate bandwidth

◆ Non-blocking switching architecture

◆ Spanning Tree Protocol

◆ Up to four port trunks

◆ RADIUS and TACACS+ authentication

◆ Rate limiting for bandwidth management

◆ CoS support for four-level priority

◆ Full support for VLANs with GVRP

◆ IP Multicasting with IGMP Snooping

◆ Manageable via console, Web, SNMP/RMON

Installation Guide

SMC6716AL2

Summary of content (86 pages)

PAGE 1
TigerSwitch 10/100 16-Port Fast Ethernet Switch ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ 16 10BASE-T/100BASE-TX ports Optional 1000BASE-X or 100BASE-FX modules 8.
PAGE 2
PAGE 3
TigerSwitch 10/100 Installation Guide From SMC’s Tiger line of feature-rich workgroup LAN solutions 38 Tesla Irvine, CA 92618 Phone: (949) 679-8000 August 2004 Pub.
PAGE 4
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright © 2004 by SMC Networks, Inc. 38 Tesla Irvine, CA 92618. All rights reserved.
PAGE 5
LIMITED WARRANTY Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace any product not operating as warranted with a similar or functionally equivalent product, during the applicable warranty term.
PAGE 6
WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
PAGE 7
COMPLIANCES FCC - Class A This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart B of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
PAGE 8
COMPLIANCES CE Mark Declaration of Conformance for EMI and Safety (EEC) SMC contact for these products in Europe is: SMC Networks Europe, Edificio Conata II, Calle Fructuós Gelabert 6-8, 2o, 4a, 08970 - Sant Joan Despí, Barcelona, Spain.
PAGE 9
COMPLIANCES Japan VCCI Class A Australia AS/NZS 3548 (1995) - Class A SMC contact for products in Australia is: SMC Communications Pty. Ltd. Suite 18, 12 Tryon Road, Lindfield NSW2070, Phone: 61-2-94160437 Fax: 61-2-94160474 Safety Compliance Warning: Fiber Optic Port Safety CLASS I LASER DEVICE When using a fiber optic port, never look at the transmit laser while it is powered on. Also, never look directly at the fiber TX port and fiber cable ends when they are powered on.
PAGE 10
COMPLIANCES Power Cord Safety Please read the following safety information carefully before installing the switch: WARNING: Installation and removal of the unit must be carried out by qualified personnel only. • The unit must be connected to an earthed (grounded) outlet to comply with international safety standards. • Do not connect the unit to an A.C. outlet (power supply) without an earth (ground) connection.
PAGE 11
COMPLIANCES Power Cord Set Europe The supply plug must comply with CEE7/7 (“SCHUKO”). The mains cord must be or marked and be of type HO3VVF3GO.75 (minimum). IEC-320 receptacle. Veuillez lire à fond l'information de la sécurité suivante avant d'installer le Switch: AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être confiés à un personnel qualifié.
PAGE 12
COMPLIANCES Cordon électrique - Il doit être agréé dans le pays d’utilisation Etats-Unis et Canada: Le cordon doit avoir reçu l’homologation des UL et un certificat de la CSA. Les spe'cifications minimales pour un cable flexible sont AWG No. 18, ouAWG No. 16 pour un cable de longueur infe'rieure a` 2 me'tres. - type SV ou SJ - 3 conducteurs Le cordon doit être en mesure d’acheminer un courant nominal d’au moins 10 A.
PAGE 13
COMPLIANCES Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden: Schweiz Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen einhalten. Europe Das Netzkabel muß vom Typ HO3VVF3GO.75 (Mindestanforderung) sein und die Aufschrift oder tragen. Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”). Warnings and Cautionary Messages Warning: This product does not contain any serviceable user parts.
PAGE 14
COMPLIANCES End of Product Life Span This product is manufactured in such a way as to allow for the recovery and disposal of all included electrical components once the product has reached the end of its life. Manufacturing Materials There are no hazardous nor ozone-depleting materials in this product. Documentation All printed documentation for this product uses biodegradable paper that originates from sustained and managed forests. The inks used in the printing process are non-toxic.
PAGE 15
TABLE OF CONTENTS TABLE OF CONTENTS 1 About the TigerSwitch 10/100 . . . . . . . . . . . . . . . . . . . 1-1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switch Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Management Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description of Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RJ-45 Ports . . . .
PAGE 16
TABLE OF CONTENTS Connecting to the Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Wiring Map for RJ-45 Console Cable . . . . . . . . . . . . . . . . . . . . . 3-9 4 Making Network Connections . . . . . . . . . . . . . . . . . . . 4-1 Connecting Network Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Twisted-Pair Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cabling Guidelines . . . . . . . . . . . . . . .
PAGE 17
TABLE OF CONTENTS C Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-1 Physical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 Base Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 Switch Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2 Management Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 18
TABLES Table 1-1 Table 1-2 Table 3-1 Table 4-1 Table 4-2 Table 4-5 Table 4-3 Table 4-4 Table A-1 Table B-1 Table B-2 Table B-3 Table B-4 Table D-1 xiv Port Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 System Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Console Port to 9-Pin DTE Port in PC . . . . . . . . . . . . . . . . 3-9 Maximum Cable length for 1000BASE-T . . . . . . . . . . . . . .
PAGE 19
FIGURES Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4 Figure 1-5 Figure 1-6 Figure 1-7 Figure 1-8 Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6 Figure 3-7 Figure 4-1 Figure 4-2 Figure 4-3 Figure B-1 Figure B-2 Figure B-3 Figure B-4 SMC6716AL2 Front and Rear Panels . . . . . . . . . . . . . . . 1-1 Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 System LEDs . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 20
FIGURES xvi
PAGE 21
CHAPTER 1 ABOUT THE TIGERSWITCH 10/100 Overview SMC’s TigerSwitch™ 10/100 (SMC6716AL2) contains 16 10BASE-T / 100BASE-TX (RJ-45) ports plus two slots on the front panel for slide-in modules (100BASE-FX, 1000BASE-T, or 1000BASE-X (GBIC)). There is also an SNMP-based management agent embedded on the main board. This agent supports both in-band and out-of-band access for managing the switch.
PAGE 22
ABOUT THE TIGERSWITCH 10/100 Switch Architecture The switch employs a wire-speed, non-blocking switching fabric. This permits simultaneous wire-speed transport of multiple packets at low latency on all ports. This switch also features full-duplex capability on all ports, which effectively doubles the bandwidth of each connection. The Switch uses store-and-forward switching to ensure maximum data integrity.
PAGE 23
DESCRIPTION OF HARDWARE Description of Hardware RJ-45 Ports The switch base unit contains 16 10BASE-T / 100BASE-TX RJ-45 ports. All of these ports support automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs. (See “10BASE-T/100BASE-TX Pin Assignments” on page B-2.
PAGE 24
ABOUT THE TIGERSWITCH 10/100 Table 1-1 Port Status LEDs LED Condition Status Base Unit Ports 1~16 (Link/Act) On/ Flashing Amber Port has established a valid network connection. Flashing indicates activity. On/ Flashing Green Port has established a valid 100 Mbps network connection. Flashing indicates activity. Off There is no valid link on the port. On/ Flashing Amber Port has established a valid 10/100 Mbps network connection. Flashing indicates activity.
PAGE 25
DESCRIPTION OF HARDWARE Table 1-2 System Status LEDs LED Condition Status PWR On Green The unit’s internal power supply is operating normally. Off The unit has no power connected. On Green The system diagnostic test has completed successfully. Flashing Green The system diagnostic test is in progress. On Amber The system diagnostic test has detected a fault.
PAGE 26
ABOUT THE TIGERSWITCH 10/100 Optional 100BASE-FX Module (SMC6824FSSC) 100BASE-FX Singlemode Module TX RX SMC6824FSSC Figure 1-5 Single-Port 100BASE-FX Single-Mode Module Using single-mode fiber optic cable, the 100BASE-FX port can be connected to a remote site up to 20 km (12.4 miles) away. The 100BASE-FX module operates at 100 Mbps, with support for full-duplex mode and flow control.
PAGE 27
DESCRIPTION OF HARDWARE Optional 1000BASE-X GBIC Module (SMC6824GB) 1000BASE-X GBIC Module SMC6824GB Figure 1-7 Single-Port 1000BASE-X GBIC Module This module supports 5 V 1000BASE-SX, 1000BASE-LX and 1000BASE-ZX GBIC transceivers: 1000BASE-SX GBIC transceivers provide one short-wavelength (850 nm) Gigabit port that can be used for a high-speed backbone or server connection. This port can be connected to a site up to 220 m (722 ft) away with 62.
PAGE 28
ABOUT THE TIGERSWITCH 10/100 Power Supply Receptacle The power receptacle is located on the rear panel of the switch. The standard power receptacle is for the AC power cord. 100-240V~ 50-60Hz 0.
PAGE 29
FEATURES AND BENEFITS Expandability • Optional single-port 1000BASE-T Gigabit module • Optional single-port 100BASE-FX multimode and single-mode modules • Optional single-port 1000BASE-X GBIC module that supports a single-port 1000BASE-SX, 1000BASE-LX, or 1000BASE-ZX GBIC transceiver. Performance • Transparent bridging • Aggregate bandwidth up to 8.
PAGE 30
ABOUT THE TIGERSWITCH 10/100 1-10
PAGE 31
CHAPTER 2 NETWORK PLANNING Introduction to Switching A network switch allows simultaneous transmission of multiple packets via non-crossbar switching. This means that it can partition a network more efficiently than bridges or routers. The switch has, therefore, been recognized as one of the most important building blocks for today's networking technology.
PAGE 32
NETWORK PLANNING Application Examples The TigerSwitch 10/100 is not only designed to segment your network, but also to provide a wide range of options in setting up network connections and linking VLANs. Some typical applications are described below. Collapsed Backbone The TigerSwitch 10/100 is an excellent choice for mixed Ethernet and Fast Ethernet installations where significant growth is expected in the near future.
PAGE 33
APPLICATION EXAMPLES Network Aggregation Plan With 16 parallel bridging ports (i.e., 16 distinct collision domains), this switch can collapse a complex network down into a single efficient bridged node, increasing overall bandwidth and throughput. In the figure below, the 10BASE-T/100BASE-TX ports on the switch are providing 100 Mbps connectivity for up to 16 segments. In addition, the switch is also connecting servers at 100 Mbps.
PAGE 34
NETWORK PLANNING Remote Connection with Fiber Cable Fiber optic technology allows for longer cabling than any other media type. A 100BASE-FX multimode fiber (MMF) link can run up to 2 km, and a 100BASE-FX single-mode fiber (SMF) link can run as far as 20 km. This allows the switch to serve as a collapsed backbone, providing direct connectivity for a widespread LAN. The 100BASE-FX (SMF) slide-in module or 1000BASE-ZX GBIC transceiver can be used to interconnect remote network segments.
PAGE 35
APPLICATION EXAMPLES Making VLAN Connections This switch supports VLANs which can be used to organize any group of network nodes into separate broadcast domains. VLANs confine broadcast traffic to the originating group, and can eliminate broadcast storms in large networks. This provides a more secure and cleaner network environment. VLANs can be based on untagged port groups, or traffic can be explicitly tagged to identify the VLAN group to which it belongs.
PAGE 36
NETWORK PLANNING Application Notes 1. Full-duplex operation only applies to point-to-point access (such as when a switch is attached to a workstation, server or another switch). When the switch is connected to a hub, both devices must operate in half-duplex mode. 2. Avoid using flow control on a port connected to a hub unless it is actually required to solve a problem. Otherwise back pressure jamming signals may degrade overall performance for the segment attached to the hub. 3.
PAGE 37
CHAPTER 3 INSTALLING THE SWITCH Selecting a Site TigerSwitch 10/100 units can be mounted in a standard 13-inch equipment rack or on a flat surface. Be sure to follow the guidelines below when choosing a location. ◆ The site should: • be at the center of all the devices you want to link and near a power outlet.
PAGE 38
INSTALLING THE SWITCH Ethernet Cabling To ensure proper operation when installing the switch into a network, make sure that the current cables are suitable for 10BASE-T or 100BASE-TX or 1000BASE-T operation. Check the following criteria against the current installation of your network: • Cable type: Unshielded twisted pair (UTP) or shielded twisted pair (STP) cables with RJ-45 connectors; Category 3 or better for 10BASE-T, Category 5 or better for 100BASE-TX, and Category 5, 5e, or 6 for 1000BASE-T.
PAGE 39
EQUIPMENT CHECKLIST Equipment Checklist After unpacking the TigerSwitch 10/100, check the contents to be sure you have received all the components. Then, before beginning the installation, be sure you have all other necessary installation equipment.
PAGE 40
INSTALLING THE SWITCH Mounting A TigerSwitch 10/100 unit can be mounted in a standard 13-inch equipment rack or on a desktop or shelf. Mounting instructions for each type of site follow. Installing Optional Modules: Before mounting the switch, be sure you install any optional modules. If you have purchased optional slide-in 1000BASE-T, 100BASE-FX or GBIC media expansion module, install these modules now, following the instructions in “Installing an Optional Module into the Switch” on page 3-7.
PAGE 41
MOUNTING To rack-mount devices: 1. Attach the brackets to the device using the screws provided in the Bracket Mounting Kit. PW R Di ag M1 M2 Figure 3-2 Attaching the Brackets 2. Mount the device in the rack, using four rack-mounting screws (not provided). PW R Di ag M1 M2 Figure 3-3 Installing the Switch in a Rack 3. If installing a single switch only, turn to “Connecting to a Power Source” at the end of this chapter. 4.
PAGE 42
INSTALLING THE SWITCH Desktop or Shelf Mounting 1. Attach the four adhesive feet to the bottom of the first switch. M2 M1 PW R Dia g T ig 6 7 e rS w 16 A L it c h 2 10 /1 00 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Figure 3-4 Attaching the Adhesive Feet 2. Set the device on a flat surface near an AC power source, making sure there are at least two inches of space on all sides for proper air flow. 3.
PAGE 43
MOUNTING Installing an Optional Module into the Switch PW R Di ag M1 M2 100BA SE-FX Single mode Modul e TX RX Figure 3-5 Installing an Optional Module Caution: DO NOT install slide-in modules with the switch powered on. Be sure you power off the switch before installing any module. To install an optional module into the switch, do the following: 1. Disconnect power to the switch. 2.
PAGE 44
INSTALLING THE SWITCH Connecting to a Power Source To connect a device to a power source: 1. Insert the power cable plug directly into the receptacle located at the back of the device. 100-240V~ 50-60Hz 0.8A Figure 3-6 Power Receptacle 2. Plug the other end of the cable into a grounded, 3-pin socket. Note: For International use, you may need to change the AC line cord. You must use a line cord set that has been approved for the receptacle type in your country. 3.
PAGE 45
CONNECTING TO THE CONSOLE PORT Connecting to the Console Port The RJ-45 console port on the switch’s front panel is used to connect to the switch for out-of-band console configuration. The on-board configuration program can be accessed from a terminal or a PC running a terminal emulation program. The console port pin assignments and console cable wiring is provided in the table below. See “Cables” on page B-1 for further information on cabling.
PAGE 46
INSTALLING THE SWITCH The console port’s configuration requirements are as follows: 3-10 • Default Baud rate—9,600 bps • Character Size—8 Characters • Parity—None • Stop bit—One • Data bits—8
PAGE 47
CHAPTER 4 MAKING NETWORK CONNECTIONS Connecting Network Devices The TigerSwitch 10/100 is designed to be connected to 10 or 100 Mbps network cards in PCs and servers, as well as to other switches and hubs. It may also be connected to remote devices using the optional fiber optic modules. Twisted-Pair Devices Each device requires a shielded or unshielded twisted-pair (STP or UTP) cable with RJ-45 connectors at both ends.
PAGE 48
MAKING NETWORK CONNECTIONS Caution: Do not plug a phone jack connector into an RJ-45 port. This will damage the switch. Use only twisted-pair cables with RJ-45 connectors that conform to FCC standards. Connecting to PCs, Servers, Hubs and Switches 1. Attach one end of a twisted-pair cable segment to the device’s RJ-45 connector. Figure 4-1 Making Twisted-Pair Connections 2.
PAGE 49
TWISTED-PAIR DEVICES 3. As each connection is made, the Link LED (on the TigerSwitch) corresponding to each port will light to indicate that the connection is valid. Wiring Closet Connections Today, the punch-down block is an integral part of many of the newer equipment racks. It is actually part of the patch panel. Instructions for making connections in the wiring closet with this type of equipment follows. 1.
PAGE 50
MAKING NETWORK CONNECTIONS 3. Label the cables to simplify future troubleshooting.
PAGE 51
FIBER OPTIC DEVICES Fiber Optic Devices An optional slide-in 100BASE-FX module or GBIC transceiver can be used for backbone and long distance connections. Each multimode fiber optic port requires 50/125 or 62.5/125 micron multimode fiber optic cabling with an SC connector at both ends. If you need to connect to a device with 62.5/125 micron cable that has ST-type connectors, SMC provides an optional SC-ST Converter (Part Number: 99-012034-091).
PAGE 52
MAKING NETWORK CONNECTIONS 3. Connect one end of the cable to the SC port on the switch and the other end to the SC port on the other device. Since SC connectors are keyed, the cable can be attached in only one orientation. 100B ASE- SC fiber connector FX Si ngle-m ode M odule PW R Di ag M1 M2 Figure 4-3 Making SC Port Connections 4. As a connection is made, check the Activity LED on the switch’s front panel for the corresponding module to be sure that the connection is valid.
PAGE 53
CONNECTIVITY RULES Connectivity Rules When adding hubs (repeaters) to your network, please follow the connectivity rules listed in the manuals for these products. However, note that because switches break up the path for connected devices into separate collision domains, you should not include the switch or connected cabling in your calculations for cascade length involving other devices.
PAGE 54
MAKING NETWORK CONNECTIONS Table 4-3 Maximum 1000BASE-LX Gigabit Ethernet Cable Length Fiber Size Fiber Bandwidth Maximum Cable Length Connector 9/125 micron single-mode fiber N/A 2 m - 5 km (7 ft - 3.2 miles) SC Table 4-4 Maximum 1000BASE-ZX Fiber Optic Cable Length Fiber Size Fiber Bandwidth Maximum Cable Length Connector 9/125 micron single-mode fiber N/A 70* - 100 km (43.5 - 62.
PAGE 55
CABLE LABELING AND CONNECTION RECORDS Cable Labeling and Connection Records When planning a network installation, it is essential to label the opposing ends of cables and to record where each cable is connected. Doing so will enable you to easily locate inter-connected devices, isolate faults and change your topology without need for unnecessary time consumption. To best manage the physical implementations of your network, follow these guidelines: • Clearly label the opposing ends of each cable.
PAGE 56
MAKING NETWORK CONNECTIONS 4-10
PAGE 57
APPENDIX A TROUBLESHOOTING Diagnosing Switch Indicators Table A-1 Troubleshooting Chart Symptom Action Power LED is Off • Internal power supply has failed or is disconnected. • Check connections between the switch, the power cord, the wall outlet. Link LED is Off • Verify that the switch and attached device are powered on. • Be sure the cable is plugged into both the switch and corresponding device. • Verify that the proper cable type is used and its length does not exceed specified limits.
PAGE 58
TROUBLESHOOTING Power and Cooling Problems If the power indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or internal power supply. However, if the unit powers off after running for a while, check for loose power connections, power losses or surges at the power outlet, and verify that the fans on the unit are unobstructed and running prior to shutdown.
PAGE 59
APPENDIX B CABLES Twisted-Pair Cable and Pin Assignments Caution: DO NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards. For 100BASE-TX/10BASE-T connections, a twisted-pair cable must have two pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be green and the other, white with green stripes. Also, an RJ-45 connector must be attached to both ends of the cable.
PAGE 60
CABLES 10BASE-T/100BASE-TX Pin Assignments Use unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for RJ-45 connections: 100-ohm Category 3, 4 or 5 cable for 10 Mbps connections or 100-ohm Category 5 cable for 100 Mbps connections. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet).
PAGE 61
TWISTED-PAIR CABLE AND PIN ASSIGNMENTS Straight-Through Wiring If the twisted-pair cable is to join two ports and only one of the ports has an internal crossover (MDI-X), the two pairs of wires must be straight-through. (When auto-negotiation is enabled for any RJ-45 port on this switch, you can use either straight-through or crossover cable to connect to any device type.
PAGE 62
CABLES EIA/TIA 568B RJ-45 Wiring Standard 10/100BASE-TX Crossover Cable White/Orange Stripe Orange End A 1 2 3 4 5 6 7 8 White/Green Stripe Blue White/Blue Stripe Green 1 2 3 4 5 6 7 8 End B White/Brown Stripe Brown Stripe Figure B-3 Crossover Wiring 1000BASE-T Pin Assignments All 1000BASE-T ports support automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs.
PAGE 63
TWISTED-PAIR CABLE AND PIN ASSIGNMENTS Table B-2 1000BASE-T MDI and MDI-X Port Pinouts Pin MDI Signal Name MDI-X Signal Name 1 Bi-directional Data One Plus (BI_D1+) Bi-directional Data Two Plus (BI_D2+) 2 Bi-directional Data One Minus (BI_D1-) Bi-directional Data Two Minus (BI_D2-) 3 Bi-directional Data Two Plus (BI_D2+) Bi-directional Data One Plus (BI_D1+) 4 Bi-directional Data Three Plus (BI_D3+) Bi-directional Data Four Plus (BI_D4+) 5 Bi-directional Data Three Minus (BI_D3-) Bi-directi
PAGE 64
CABLES Adjusting Existing Category 5 Cabling If your existing Category 5 installation does not meet one of the test parameters for 1000BASE-T, there are basically three measures that can be applied to try to correct the problem: 1. Replace any Category 5 patch cables with high-performance Category 5e or 6 cables. 2. Reduce the number of connectors used in the link. 3. Reconnect some of the connectors in the link.
PAGE 65
CONSOLE PORT PIN ASSIGNMENTS Console Port Pin Assignments The console port on the switch’s front panel is used to connect to the switch for out-of-band console configuration. The port uses conventional RS-232 compatible signal levels through an RJ-45 connector on the switch panel. The on-board configuration program can be accessed from a terminal or a PC running a terminal emulation program.
PAGE 66
CABLES Console Port to 9-Pin DTE Port on PC Table B-4 Console Port to 9-Pin DTE Port in PC Switch’s RJ-45 Console Port Null Modem 6 RXD <---------TXD ------------ 3 TXD 3 TXD -----------RXD ----------> 2 RXD 4, 5 SGND -----------SGND ---------- 5 SGND No other pins are used.
PAGE 67
APPENDIX C SPECIFICATIONS Physical Characteristics Base Unit Ports 16 10BASE-T/100BASE-TX, with auto-negotiation One RS232 serial console port fitted using an RJ-45 connector Media Slots 2 slots for optional 100BASE-FX, 1000BASE-T, or 1000BASE-X (GBIC) modules Network Interface Ports 1-16: RJ-45 connectors, auto MDI/MDI-X 10BASE-T: RJ-45 (100-ohm, UTP cable; Categories 3 or better) 100BASE-TX: RJ-45 (100-ohm, UTP cable; Category 5 or better) Communication Speed 10 and 100 Mbps Communication Mode Full and ha
PAGE 68
SPECIFICATIONS LEDs System: PWR (Power), Diag (Diagnostics) Ports: Link/Activity Weight 2.2 kg (4.8 lbs) Size 33 x 23.0 x 4.4 cm (13 x 9.06 x 1.7 in.) Temperature Operating: 0 to 50 °C (32 to 122 °F) Storage: -40 to 70 °C (-40 to 158 °F) Humidity Operating: 10% to 90% Power Supply Internal, auto-ranging transformer: 100 to 240 VAC, 50 to 60 Hz Power Consumption 28 Watts maximum Heat Dissipation 95.6 BTU/hr maximum Maximum Current 0.
PAGE 69
MANAGEMENT FEATURES Flow Control Full Duplex: IEEE 802.3x Half Duplex: Back pressure Management Features In-Band Management Telnet, Web-based HTTP, or SNMP manager (EliteView Network Management software provided free) Out-of-Band Management RJ-45 console port Software Loading TFTP in-band, or XModem out-of-band Standards IEEE 802.3 Ethernet, IEEE 802.3u Fast Ethernet IEEE 802.3z and IEEE 802.3ab Gigabit Ethernet IEEE 802.1p priority tags IEEE 802.3ac VLAN tagging IEEE 802.
PAGE 70
SPECIFICATIONS Compliances CE Mark Emissions FCC Class A Industry Canada Class A EN55022 (CISPR 22) Class A EN 61000-3-2/3 VCCI Class A C-Tick - AS/NZS 3548 (1995) Class A Immunity EN 61000-4-2/3/4/5/6/11 Safety CSA/CUS (CSA 22.2 No.
PAGE 71
SLIDE-IN MODULES Slide-in Modules 100BASE-FX Extender Modules Models SMC6824FSSC, SMC6824FMSC Ports 1 100BASE-FX Network Interface SMC6824FSSC: 9/125 micron single-mode fiber cable SMC6824FMSC 50/125 or 62.5/125 micron multimode fiber cable Standards IEEE 802.3u Fast Ethernet ISO/IEC 8802-3 Weight 50 gm (1.8 oz) Size 6.0 x 9.1 cm (2.37 x 2.56 in.
PAGE 72
SPECIFICATIONS Weight 55 gm (1.98 oz) Size 6.0 x 9.1 cm ( 2.37 x 2.56 in.) 1000BASE-X GBIC Module Model SMC6824GB Ports 1 slot for GBIC transceivers Communication Speed 1000 Mbps Communication Mode Full Duplex Standards IEEE 802.
PAGE 73
APPENDIX D ORDERING INFORMATION Table D-1 TigerSwitch 10/100 Products and Accessories Product Number Description SMC6716AL2 16-port Fast Ethernet switch with two media expansion slots SMC6824GT Gigabit module with one 1000BASE-T port (RJ-45 connector) SMC6824FSSC Extender module with one 100BASE-FX single-mode fiber port (SC-type connector) SMC6824FMSC Extender module with one 100BASE-FX multimode fiber port (SC-type connector) SMC6824FMST SMC6824FMSC + SC-ST converter SMC6824GB Gigabit module
PAGE 74
ORDERING INFORMATION D-2
PAGE 75
GLOSSARY 10BASE-T IEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3 or better UTP cable. 100BASE-TX IEEE 802.3u specification for 100 Mbps Fast Ethernet over two pairs of Category 5 or better UTP cable. 100BASE-FX IEEE 802.3u specification for 100 Mbps Fast Ethernet over two strands of 50/125 or 62.5/125 micron core fiber cable. 1000BASE-LX IEEE 802.3z specification for Gigabit Ethernet over two strands of 9/125 micron core single-mode fiber cable. 1000BASE-SX IEEE 802.
PAGE 76
mode (e.g., 10, 100, or 1000 Mbps and half or full duplex) based on the capabilities of the node to which it is connected. Bandwidth The difference between the highest and lowest frequencies available for network signals. Also synonymous with wire speed, the actual speed of the data transmission along the cable. Collision A condition in which packets transmitted over the cable interfere with each other. Their interference makes both signals unintelligible. Collision Domain Single CSMA/CD LAN segment.
PAGE 77
Fast Ethernet Switch Device that provides a full 100 Mbps bandwidth (or either 10 or 100 Mbps bandwidth with Auto-Negotiation) to each port (LAN segment). Full Duplex Transmission method that allows switch and network card to transmit and receive concurrently, effectively doubling the bandwidth of that link. Gigabit Ethernet A 1000 Mbps network communication system based on Ethernet and the CSMA/CD access method. IEEE 802.
PAGE 78
Separate LAN or collision domain. LED Light emitting diode used for monitoring a device or network condition. Link Segment Length of twisted-pair or fiber cable joining a pair of repeaters or a repeater and a PC. Local Area Network (LAN) A group of interconnected computer and support devices. Media Access Control (MAC) A portion of the networking protocol that governs access to the transmission medium, facilitating the exchange of data between network nodes. MIB An acronym for Management Information Base.
PAGE 79
any device having a crossover port. Also referred to as a “Daisy-Chain” port. Switched Ports Ports that are on separate collision domains or LAN segments. Transmission Control Protocol/Internet Protocol (TCP/IP) Protocol suite that includes TCP as the primary transport protocol, and IP as the network layer protocol. UTP Unshielded twisted-pair cable.
PAGE 80
Glossary-6
PAGE 81
INDEX Numerics C 10/100 Mbps connectivity rules 4-8 10/100/1000BASE-T modules 1-5 1000 Mbps connectivity rules 4-7 1000BASE-T cable lengths 4-7 1000BASE-X modules 1-7 100BASE-FX connections 4-5 fiber cable lengths 4-8 modules 1-6 100BASE-TX cable lengths 4-8 ports 1-3 10BASE-T cable lengths 4-8 ports 1-3 cable Ethernet cable compatibility 3-2 labeling and connection records 4-9 lengths 4-7, 4-8 specifications B-1 cleaning fiber terminators 4-5 compliances EMC C-4 safety C-4 connectivity rules 10/100 Mbps
PAGE 82
INDEX G Gigabit Ethernet cable lengths 4-7 grounding for racks 3-4 I indicators, LED 1-3 installation desktop or shelf mounting 3-6 installing optional modules 3-4 port connections 4-5 power requirements 3-1 problems A-2 rack mounting 3-4 site requirements 3-1 wiring closet connections 4-3 L laser safety 4-5 LED indicators Diag 1-5 Link/Act 1-4 Power 1-5 problems A-1 limited warranty C-4 location requirements 3-1 M management agent 1-2 features 1-9, C-3 out-of-band 1-2 SNMP 1-2 Web-based 1-2 Index-2 m
PAGE 83
INDEX R rack mounting 3-4 rear panel receptacles 1-8 RJ-45 port 1-3 pinouts B-4 rubber foot pads, attaching 3-6 S sample applications 2-2 SC port connections 4-5 screws for rack mounting 3-3 SC-ST Converter 4-5, 4-6, D-1 site selelction 3-1 SNMP agent 1-2 specifications 1000BASE-X GBIC module C-6 compliances C-4 environmental C-2 physical C-1 power C-2 standards compliance C-4 IEEE C-3 status LEDs 1-3 surge suppressor, using 3-1 switch architecture 1-2 switching method 1-2 switching, introduction to 2-1
PAGE 84
INDEX Index-4
PAGE 85
PAGE 86
FOR TECHNICAL SUPPORT, CALL: From U.S.A. and Canada (24 hours a day, 7 days a week) (800) SMC-4-YOU; (949) 679-8000; Fax: (949) 679-1481 From Europe (8:00 AM - 5:30 PM UK Time) 44 (0) 118 974 8700; Fax: 44 (0) 118 974 8701 INTERNET E-mail addresses: techsupport@smc.com european.techsupport@smc-europe.com support@smc-asia.com Driver updates: http://www.smc.com/index.cfm?action=tech_support_drivers_downloads World Wide Web: http://www.smc.com http://www.smc-europe.com http://www.smc-asia.