Remote View Door Phone Installation and Operating Instructions Model: RVDP-GS Version 1.0 PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT AND KEEP THIS MANUAL FOR FUTURE REFERENCE.
The state of art Remote View Door Phone (RVDP) is capable of deliver High Definition (HD) video to your smart-mobile device(s), which would require higher internet bandwidth. Due to your local internet environment condition, your mobile device(s) may display black-screen or temporary disconnect to the Remote View Door Phone (RVDP). * Make sure your RVDP is operating with sufficient internet bandwidth; 1Mbps (upload/download speed) are suggested.
CONTENTS INTRODUCTION............................................................................................... 2 IMPORTANT SAFETY PRECAUTIONS......................................................................2 KIT CONTENT.................................................................................................. 4 KNOWING YOUR DEVICES............................................................................. 5 HARDWARE OVERVIEW ............................................................
INTRODUCTION PLEASE READ BEFORE YOU START Always use discretion when installing CCTV equipment, especially when there is perceived policy. Enquire relevant local regulations applicable to the lawful installation of video recording/ surveillance. Third party consent may be required. WIRELESS DEVICES OPERATING RANGE I Ensure the signal reception viewed from the wireless camera(s) is the best possible reception between the camera(s) and the Wi-Fi router.
FCC Compliance Statement: This Products with CE Marking comply with device complies with Part 15 of the EMC Directive (2014/30/EU); Low Voltage FCC rules. Operation is subjected to Directive (2014/35/EU); RED(2014/53/ the following two conditions: (1) this EU); ROHS Directive (2011/65/EU) issued device may not cause harmful interference, and (2) this by the Commission of the European Community.
KIT CONTENT Wall-Bracket RVDP x1 x1 Power Adapter DC Power Cable Black Red x1 x1 Lock/Gate Cable Bell cable White Black Blue Black x1 x2 Quick Start Guide Screw Pack x1 x1 Note: For video recording, BE SURE TO use CLASS 10 memory card or above. Other kinds of memory card may cause unexpected results and should be avoided.
HARDWARE OVERVIEW Memory Card Slot Sunshade Mounting Bracket Camera with IR-Cut Motion Sensor Weather Resistant Spearker Push Button Microphone Reset Button 1 1. RX+/RX-/TX+/TX-: Ethernet Cable I/O* 2. V-/V+: Power Input I/O 3. O2/O1: Wet Contact I/O 4. B2/B1: Bell Contact I/O 5. C2/C1: Dry Contact I/O *Ethernet cable not included in the package.
REMOTE VIEW DOOR PHONE SETUP & INSTALLATION △ BEFORE YOU START ‧Do not mount the RVDP until completing the Wi-Fi connection setup. ‧First connect power to the RVDP using the supplied Power Input Cable to 9-36V power source. ‧After connecting power to RVDP, the boot up process will begin (> 2 minutes), the red/green LED will become steady on after the boot up process is complete (check connectors and power source if red/green LED do not come on).
OPERATION DIAGRAM The Remote View Door Phone (RVDP) is designed to deliver live video directly to your smart mobile devices after visitor have pressed the communication button on the door unit. The RVDP app will allow you to see live video, speak to the visitor, manually capture snapshot/video and even open the door (3rd party door lock device required) for the visitor.
APP DOWNLOAD AND INSTALL - Please download and install the "OMGuard HD” APP to your device. For iOS For Android APP Setup 1. In the Wi-Fi setting section of your smart phone/tablet, search for RVDP SSID (example: HD-XXXXXX) and connect. The default password is 12345678. 2. Lanuch the app and tap to add RVDP 3. Tap Search to pull in DID information, or enter the DID manually. 4. Enter name for your RVDP (maximum 20 characters). 5. Enter default Security Code 123456. 6.
7. Tap and then to enter the advanced setting 8. Tap advanced setting to enter default password:123456 (iOS) (Android) 9. Scroll down to Wi-Fi Setting section, select the Wi-Fi router and enter its pas sword. Advanced Settings WiFi Setting Management WiFi Refresh WiFi WiFi setting will take effect after system reboot. Enable notification Save Important Note: After the default password entered, the app will remind you to change it, which is strongly recommended for security purpose.
In most cases, you can successfully add the camera according to the steps above. However, the camera will not find the network if Wi-Fi router turns off the SSID broadcasting function. Please enable the SSID broadcasting to complete the settings. Note: If you do not see your Wi-Fi router in the WI-FI SETTING section, please enable your router's SSID broadcasting function, which usually is the name of your HOME WI-FI NETWORK. Most of the Wi-Fi routers broadcast the Service Set Identifier (SSID) by default.
MAIN PAGE OVERVIEW The MAIN PAGE section offers you an overview for RVDP and access to different management functions. MAIN PAGE - List of all registered RVDP. You can quickly access preferred RVDP in the list even when multiple RVDP are registered by scrolling the list up or down. - Tap the camera to enter Live-View. - The Connection Status (Connected or Disconnected)is indicated for each RVDP in the list. (iOS) (Android) Add RVDP : To add RVDP.
ADD RVDP Tap to add RVDP. Please refer to page 8 "APP Setup" section for more details. SETTING Tap and additional setup selection icons will appear. Tap to exit. Additional setup selection (iOS) (Android) RVDP INFORMATION : Change RVDP name, reset Wi-Fi router setting and access Advanced Setting section. DELETE RVDP : Remove the RVDP. EVENT LIST : View and playback the list of motion triggered event(s) for the particular RVDP.
SETUP PIN LOCK MUST enter PIN code when you have enable PIN lock function with launching the APP. 1. Enable "Enable lock when starting" and enter your PIN code. 2. Confirm PIN code entered. (iOS) (Android) Note: If you forgot the PIN code, please delete and reinstall the app. NOTIFY (PUSH NOTIFICATION) The WAPP camera supports motion detection. When a motion is detected, you’ll receive push notification on the mobile devices for the event recognized by the camera.
For Android If you want to enable/disable it, please follow the steps below. Note: The internet connection and wireless network interference may influence the performance of push notification service. ABOUT APP/API Version Info (iOS) (Android) Tap the ABOUT icon to check the APP Version when necessary.
VISITOR CALL-IN PAGE Call-In Screen Live-View Audio Only Talk Botton Recording Door Unlock A Gate Unlock B Mute Snapshot Back to Main Page Push-To-Talk Tap and hold to speak with visitor. No sound will be transmitted if you let go. Snapshot Tap once to capture a single still image of the video coming from the door unit. The still image files are stored within your mobile device. Mute Tap once to mute the audio coming from the door unit. Tap again to resume.
ANSWERING A CALL 1 2 Above screen would appear When visitor pressed the bell button. 1. Ignore the communication request. 2. Accept the communication request. Note: For iOS user, due to the system fundamental structural design, you will have to confirm/accept incoming communication request via pop-ups first before the answering section would appear. For more details, please refer to the manual.
SETUP THE RVDP 1. Remove the compartment cover with screws. 2. Insert the Micro SD card. 3. Connect power cable by pressing down the power input I/O pins. After supplied power, the boot up process will begin (> 2 minutes), the red/green LED will become steady on after the boot up process is complete (check connectors and power source if red/green LED do not come on).
ADDITIONAL WIRING DIAGRAMS A. Ethernet (Wet suppiler) Connection Tx + Cable Color Orange / White Tx - Orange Rx + Green / White Rx- Green Enthernet Cable B. Existing Bell Wiring -- + + DoorBell C. Electronic Lock - + - + Lock D.
MOUNTING THE DOOR UNIT Do not mount the RVDP until you have complete the Wi-Fi connection setup and have all the wiring process completed. It is best to test the door unit can function properly with app prior mounting the door unit. Please make sure the installation location is free from moisture and wires are not exposed in any form. Step 1 Confirm position and mount the bracket via the screws supplied. Step 2 Place the device on the mounting bracket.
PRODUCT SPECIFICATION Wireless Connectivity Wi-Fi 802.11b/g/n Transmission Frequency 2.
