DIC-23112 MANUAL
Installation We recommend for the Wi-Fi doorbell to be set-up indoors and tested before final fitting. Please follow the steps included in this guide to get the product up and running. Doorbell setup To use the recording feature, it is recommended to install the SD card before installation. This can be done later but will involve removing and re-fitting some cables. 1. Remove the 3x securing screws located on the back of the doorbell and also remove the rubber seal. 2.
. On the side of the doorbell is the SD card slot. Remove the rubber seal and insert the SD card, then push the rubber seal back into place. 4. 5. Slide the doorbell back into its aluminium case and replace the 3x securing screws. Push the power cable through the hole of the rubber seal. 6. 7. Connect the power cable to the V+ and V- connections at the back of the doorbell. Connect the red wire to the V+ terminal. Connect the black wire to the V- terminal. Don’t replace rubber seal yet.
Wall Mounting 1. 2. Now the doorbell is working, test it in your ideal location making sure you are happy with the view from the camera. Using the wall fixing base as a template, mark and drill 2 x holes using a 6mm drill bit. 3. Secure the wall fixing base to the wall using the wall plugs and screws provided. 4. 5. Drill a hole to allow the power cable to go through the wall. Feed the cable through the wall. 6. Put the doorbell onto the backplate and slide down into position.
Smartwares View App Set-up (iOS) 1. 2. 3. 4. 5. 6. Download the Smartwares View App and install it. You must allow notifications to receive Alerts on your device! Open the Smartwares View App and touch the plus icon on the screen to begin set-up. Type a name for your doorbell under system name. Click the QR code under DID and click “Allow” to open the camera on your phone. Point the camera at the QR code label on the back of the doorbell to scan it. This will automatically fill the ‘DID’ field.
7. On Wi-Fi setup click SET-UP. 8. Ensure your doorbell is still flashing blue and white and then click “Next”. If it is not flashing blue and white, then press the power button twice to turn it back on. Go to your phone Wi-Fi settings and select your required network from the list, then return to the app to enter the password for the network. 9. If your phone only has one Wi-Fi network stored then this will already be shown. Enter the password for the network. 10.
Smartwares View App Set-up (Android) 6. 7. 8. 9. 10. Download the Smartwares View App and install it. Open the Smartwares View App and touch the plus icon on the screen to begin set-up. Type a name for your doorbell under system name. Click the “Scan DID Label” and allow the app access to your camera on your phone. Point the camera at the barcode label on the back of the doorbell to scan it. This will automatically fill the ‘DID’ field. 11. Now enter the default Security code 123456 and click ‘Save’.
12. On Wi-Fi set-up click SET-UP. 13. You will be prompted to turn off your mobile data. This is to force the device to connect to the Wi-Fi of the doorbell. You can turn this back on after set-up. Return to the app and click “Start”, your device will connect to the doorbell. 14. Click the magnifying glass in the wireless network box to search for nearby Wi-Fi networks. 15. Click the network you want to connect the doorbell to and type the network password. 16. Once connected, the doorbell will ring. 17.
Smartwares View app overview Note: The screenshots in this manual may look slightly different from the app you are using. This is because there are different versions of the app for iOS and Android, and because the app is updated regularly. Start screen The start screen offers you an overview of your Smartwares Wi-fi video doorbell and other compatible Smartwares cameras you may have installed. From this screen you have access to different functions: • List of all registered cameras.
Adding a video doorbell Tap to add a video doorbell or other compatible Smartwares camera. Advanced Settings Tap . The additional setup selection icons will appear. Now tap advanced settings. Tap to access the again to exit. Note: If the device is in power saving mode, you will not be able to access the advanced settings. Wake the device first by going to live view mode. Now you will be able to access the advanced settings menu.
Setup PIN Lock If you choose to enable the PIN lock function, you are required to enter the PIN code every time when launching the app. 1. Select "Enable lock when starting" and enter your PIN code. 2. Confirm the PIN code entered. (iOS) Note: If you forget the PIN code, please delete and reinstall the app. Notifications For iOS If you want to enable/disable notifications, please follow the steps below: 1. Launch Settings from your Home screen. 2. Tap “ Notifications”. 3.
For Android If you want to enable/disable notifications, please follow the steps below. Note: The internet connection and wireless network speed may influence the performance of the push notification service. Video hardware acceleration Turn video hardware acceleration on for faster performance. Please turn this off if you experience any graphical glitches. About app/API version info Tap “about” to check the app version.
Live view page Microphone on/off Phone mode Snapshot Tap once to speak with a visitor, tap again to mute. Tap once to switch from hands-free talking mode to phone mode, tap again to switch back to hands-free mode. In phone mode, you can hold your phone up to your ear when talking to a visitor. Tap to take a snapshot. Snapshots are saved to your mobile device. Mute Tap once to mute the audio coming from the door unit. Tap again to resume. Record Tap to start a recording.
Hands-free Mode Phone mode with one-way audio Hands-free mode with two-way talk Phone mode with two-way talk
Event video playback The recorded video is automatically saved to the memory card. You can access the files for playback. Tap on the main page. Tap and the date/time filter will appear. You can define the period to display all available recorded files for playback. All available events will be stored on the MicroSD card. The number of available events will depend on the memory card storage capacity.
For playback, select the file from the local or the event section. During the playback you can tap the pause button to pause/resume the playback. The local network conditions may cause improper video playback, resulting in a black screen. If this happens please leave the playback mode and try again later when the internet conditions have improved. We strongly suggest using a good Wi-Fi connection for better performance playback. Tap once for playback, press and hold to download the file to mobile device.
Delete Select the file(s) and tap the delete icon. It’s possible to delete multiple files at once. Check the video clip Then tap the trash can icon Answering a call A pop-up like you see on the left will appear on your mobile device when a visitor presses the doorbell button on you video doorbell. • Tap “Ignore” to ignore the call. • Tap “Accept” to answer the call.
Advanced settings This chapter explains the advanced settings for the administrator. The administrator is the one who owns the administration password and has full control over the Wi-Fi video doorbell. The administrator can access all functions and settings, while normal users can only receive the surveillance images for live view, capture video recordings and cannot manage the camera settings.
Admin password The Admin Password is a specific security code for the administrator to edit the advanced settings. The default admin password is 123456. This function allows you to change the default admin password into your personal admin password. For the protection of your system configuration, you need to enter the admin password when changing the advanced settings. We strongly suggest that you change the admin password periodically.
Environment mode Choose between 50 or 60 Hz, depending on your region. If you are in Europe, you should select 50Hz. Low Light Enhancement Adjust the picture quality for darker environments Notify enable By disabling notifications here all users will not be able to receive push notifications on their mobile device, even if they have push notifications enabled. Camera name Change the name you have set for your video doorbell. SD card format Use this function to completely reformat your SD card.
you can select. Adjust melody volume You can adjust the volume from completely muted to maximum volume. Change Melody type Choose a melody for video doorbell. Door chime melody Choose a melody for your paired chime (sold separately). Audio effect (Android only) If you have issues with echoes when using two-way audio, enable the acoustic echo canceler function. Pairing with a Smartwares chime You can pair you video doorbell with a separate chime.
anyone presses your doorbell, even when you are away from your phone. We recommend the Byron BY501, 504 and 601. • Put your chime in pairing mode by pressing and holding the correct button (please check the manual for your chime), until the chime beeps. • Now press the doorbell button on the video doorbell. If the pairing is successful, your chime will ring. Factory reset Press and hold the reset button on the bottom of the device for 5 seconds to reset the system to factory default settings.
Wireless Network Transmission Frequency Transmission Range Image Sensor Remote Live-view Two-Way Audio Wi-Fi 802.11b/g/n 2.
