CIP-39901 Installation and Operating Instructions PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT AND KEEP THIS MANUAL FOR FUTURE REFERENCE.
CONTENTS OVERVIEW ...................................................................................................... 2 Please Read Before You Start ..................................................................................3 Wireless Device Operating Range ............................................................................3 Important Safety Precautions ....................................................................................3 KIT CONTENT ......................................
OVERVIEW The outdoor camera which is equipped with powerful LED light illuminates. The light can be switched on manually in the app or set to switch on when motion is detected. You can also control the camera via the app remotely from anywhere. 1Mbps (upload/ download speed) is suggested. the smart-mobile device(s) need to be on Wi-Fi or 4G mobile network in order to receive maximum download speed.
PLEASE READ BEFORE YOU START perceived policy. of video recording/surveillance. WIRELESS DEVICES OPERATING RANGE reception distance between the performance.
KIT CONTENT WAPP-LSE Wall mount bracket UP x1 x1 Hex Key Antenna x1 x1 Screw Pack Positioning Card x1 x1 Reset Pin Quick Start Guide x1 x1 Tools Required: (not included) •Electric drill •5mm masonry drill bit •15mm masonry drill bit •No. 2 Philips screwdriver • For best system performance: iOS: iPhone6 / iPad2 / Mini iPad with iOS 10.0 or above. Android: 1.5G dual core processor dual core procesor with 1G RAM or above. Storage: Class 10 memory card.
SAFETY AND INSTALLATION TIPS use of cable/pipe detector is advisable. video/power extension cables from being exposed externally and to prevent/reduce the chances of the hole is sealed up around the cable using a sealant to prevent drafts. branches or moving objects that might unnecessarily cause the camera to record.
PRODUCT OVERVIEW Antenna LED Light FHD Camera Motion Sensor Light Sensor Microphone Wall Mount Bracket Speaker Reset Button Power LED Indicator RESETU Link LED Indicator SB Memory Card Slot Micro USB Port for “only” Wi-Fi Setup Note: to factory default and you may set up the camera again.
INSTALL YOUR DEVICE For optimal performance install the lighting camera at a hight between 2.5 and 4 meters. Disconnect power at fuse or circuit breaker before proceeding to the installtion. Motion Detection 90˚ 2.5m Height ETHERNET CONNECTION (OPTIONAL) UP 1 2 3 6 1 2 3 6 I/O Pin Connector UP RX+/RX-/TX+/TX-: Ethernet Cable I/O* *Ethernet cable not included in the package.
CAMERA SETUP INSTRUCTION off Put the terminal blocks back into the base properly to protect it against water.
3 4 UP UP Connect to here 6 5 9
when you done. Wait for 1 minute for camera to connet to internet. adjust the brightness to prefer level once the camera has setup completed. have better waterproof protection.
GUARDIAN APP SETUP 1. Power on the Guardian 2. Connect your smartphone with the Wi-Fi signal (SSID) of the camera. It always starts with HD- **** and corresponds with the QR-code number on the Guardian. The default password is 12345678 3. Open the Smartwares view app and press the + button in the bottom. 4. You need to in fill 3 fields: A: System name Free to name your camera in any way you want B: DID Press Search and the DID will show.
5. You can now open the live view of the camera, by pressing below Icon. You are now directly being forced to change the default password to your own password: 6.
Press ‘Advanced’ in this screen: 7. The advanced setting are protected by an Admin password.
8. When you have accessed the advanced settings, go to WiFi setting and press Manage WiFi network: 9. Choose the Wi-Fi network name (SSID) where you want to connect to and insert the password. 10. The Guardian will restart and after approx. 1 minute your camera is restarted. Now the setup is done.
Smartwares View app overview Note: The screenshots in this manual may look slightly different from the app you are using. This is because there are different versions of the app for iOS and Android, and because the app is updated regularly. Start screen The start screen offers you an overview of your Smartwares camera and other compatible Smartwares products you may have installed. From this screen you have access to different functions: • List of all registered cameras.
Adding a camera Tap to add a camera or other compatible Smartwares product. Advanced Settings Tap . The additional setup selection icons will appear. Now tap advanced settings. Tap to access the again to exit. Device settings: Change the device name, reset the Wi-Fi settings and access the advanced settings section. Delete the device : Remove the device from your app.
Setup PIN Lock If you choose to enable the PIN lock function, you are required to enter the PIN code every time when launching the app. 1. Select "Enable lock when starting" and enter your PIN code. 2. Confirm the PIN code entered. (iOS) Note: If you forget the PIN code, please delete and reinstall the app. Notifications For iOS If you want to enable/disable notifications, please follow the steps below: 1. Launch Settings from your Home screen. 2. Tap “ Notifications”. 3.
For Android If you want to enable/disable notifications, please follow the steps below. Note: The internet connection and wireless network speed may influence the performance of the push notification service. Video hardware acceleration Turn video hardware acceleration on for faster performance. Please turn this off if you experience any graphical glitches. About app/API version info Tap “about” to check the app version.
Live view page Light button Snapshot Tap to switch between: ON / OFF / AUTO Auto mode: The light will turn on when motion is detected and only when it is dark. The light will stay on for 1 minute after motion detection. Tap to take a snapshot. Snapshots are saved to your mobile device. Mute Tap once to mute the audio coming from the camera. Tap again to resume. Record Tap to start a recording. The recorded files are stored in the MicroSD card inside the camera.
Event video playback The recorded video is automatically saved to the memory card. You can access the files for playback. Tap on the main page. Tap and the date/time filter will appear. You can define the period to display all available recorded files for playback. All available events will be stored on the MicroSD card. The number of available events will depend on the memory card storage capacity.
For playback, select the file from the event section. During the playback you can tap the pause button to pause/resume the playback. The local network conditions may cause improper video playback, resulting in a black screen. If this happens please leave the playback mode and try again later when the internet conditions have improved. We strongly suggest using a good Wi-Fi connection for better performance playback. Tap once for playback, press and hold to download the file to mobile device.
Delete Select the file(s) and tap the delete icon. It’s possible to delete multiple files at once.
Advanced settings This chapter explains the advanced settings for the administrator. The administrator is the one who owns the administration password and has full control over the camera. The administrator can access all functions and settings, while normal users can only receive the surveillance images for live view, capture video recordings and cannot manage the camera settings.
Admin password The Admin Password is a specific security code for the administrator to edit the advanced settings. The default admin password is 123456. This function allows you to change the default admin password into your personal admin password. For the protection of your system configuration, you need to enter the admin password when changing the advanced settings. We strongly suggest that you change the admin password periodically.
SD card overwrite This function will overwrite the old files when the MicroSD card is full. Turning on this function will enable the system to start overwriting oldest files when the available memory card capacity is not sufficient. This ensures the most recent video recordings can be saved so that you won’t miss any important footage. Record mode Choose if the device takes a snapshot or records a video when motion is detected.
Video resolution This section allows you to change the resolution of recorded video. There are two options you can select, VGA (640*480) or HD (1280*720). To get better quality you should select HD video. It will however consume more storage space, cause longer upload times, and higher power consumption. iOS Android Video Brightness This setting allows you adjust the brightness level of the recorded video for the best results, with level 1 being the darkest and level 7 being the brightness.
Trouble shooting IF SOLUTION You are not able to connect the camera to your Wi-Fi network… · Please put the device in close proximity to the Wi-Fi router. · The device only supports 2.4GHz, it does NOT support a 5GHz network. Please make sure that the Wi-Fi network is on a 2.4G frequency. · If you are using Android 8 (Oreo), turn off mobile data before setup, turn it on again when you’re done. Storage media management MicroSD card capacity (Class 10) Max.
