Wireless Pan/Tilt APP Camera Installation and Operating Instructions Model: C794IP PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT AND KEEP THIS MANUAL FOR FUTURE REFERENCE.
CONTENTS Overview.......................................................................................................... 2 Please Read Before You Start...................................................................................3 Wireless Device Operating Range.............................................................................3 Important Safety Precautions.....................................................................................3 Getting Started...............................
OVERVIEW The C794IP camera is capable of delivering high quality Digital High Definition (HD) video to your smart-mobile device(s), which would require higher internet bandwidth. Due to your local internet environment condition, your mobile device(s) may display black-screen or temporary disconnect to the C794IP camera. * Make sure the C794IP camera is operating with sufficient internet bandwidth, 1Mbps (upload/ download speed) is suggested.
PLEASE READ BEFORE YOU START Always use discretion when installing CCTV equipment, especially when there is perceived policy. Enquire relevant local regulations applicable to the lawful installation of video recording/surveillance. Third party consent may be required. WIRELESS DEVICES OPERATING RANGE Ensure the signal reception viewed from the wireless camera(s) is the best possible reception between the camera(s) and the Wi-Fi router.
FCC Compliance Statement: This Products with CE Marking comply device complies with Part 15 of the with EMC Directive (2004/108/EC); FCC rules. Operation is subjected to Low Voltage Directive (2006/95/ the following two conditions: (1) this EC); RED(2014/53/EU); ROHS device may not cause harmful interference, and (2) this Directive (2011/65/EU) issued by the Commission device must accept any interference received, including of the European Community.
KIT CONTENT Ethernet cable Wireless App Camera x1 x1 Power Adapter Camera Antenna x1 x1 Quick Start Guide x1 Tools Required: ‧Electric drill ‧5mm masonry drill bit ‧15mm masonry drill bit ‧No. 2 Philips screwdriver For best system performance: - iOS: iPhone5 / iPad2 / Mini iPad with iOS 7.0 or above. - Android: 1.5G dual core processor dual core procesor with 1G Ram or above. - Storage: Class 10 memory card. - Bandwidth: 1Mbps or above upload/download speed suggested.
SAFETY AND INSTALLATION TIPS Do not attempt to open the units with the power adaptor plug connected to avoid any risk of personal injury. When installing CCTV camera(s), always follow manufacturer's advice when using power tools, steps, ladders, etc. and wear suitable protective equipment (e.g. safety goggles) when drilling holes. Before drilling holes through walls, check for hidden electricity cables and water pipes. The use of cable/pipe detector is advisable.
PRODUCT OVERVIEW Light Sensor LENS Microphone Lan Port Reset Micro SD Card Slot Power LED Power Jack Antenna LED INDICATOR STATUS DESCRIPTION Power On Power on the camera and wait until the GREEN LED indicator becomes steady on. This process would be finished within 45 seconds and make sure the LED is flashing in GREEN. Soft AP Green LED flashes once followed by 2 short flashes.
INSTALLATION 1. Place the mounting bracket on the mounting surface as a pattern to mark the holes. 2. Drill the mounting holes and use the wall plug screws to secure the bracket to the wall. 3. Fasten the camera to the bracket using the tapping screws. 4. Hang the camera and plate onto the hanger screws. Arrange cable properly so that it will not block pan/tile operation.
SETUP YOUR CAMERA Follow the instructions below to help configure your camera for initial use. 1. APP download Download and install the "OMGuard HD" APP to your device. For iOS For Android 2. Power on the camera Power on the camera and wait until the GREEN LED indicator becomes steady on. This process would be finished within 45 seconds and make sure the LED is flashing in GREEN. Steady ON Power Adapter 3. Add camera 1.
(iOS) (Android) 5. In the Wi-Fi setting section, enter default password:123456. Choose the appropriate Wi-Fi router on your local network. The Camera will offline for around 40 seconds to reboot for Wifi connection. When camera connects to Wi-Fi router correctly, the Green LED will stay ON.
In most cases, you can successfully add the camera according to the steps above. However, the camera will not find the network if Wi-Fi router turns off the SSID broadcasting function. Please enable the SSID broadcasting to complete the settings. Note: In soft AP mode, the GREEN LED long flashes once followed by 2 short flashes. In normal mode, the LED is flashing in green. Most Wi-Fi routers broadcast the Service Set Identifier (SSID) by default.
LIVE VIEW / SNAPSHOT / RECORDING Tap to take snapshot image(s) of the video. The captured snapshots will be stored in your mobile device. Tap to turn ON/OFF the volume. Tap to Start/Stop recording. The recorded video file will be stored in the memory card of your camera. Tap to set/move camera to default postion Tap and hold the icon to send the voice to remote device Tap to return to the main page.
Control camera direction via finger swipe. Record the point When event triggered, the camera will immediately rotate to the scene. This fuction allows you record the camera position. You're able to select the record point you saved that the camera will go to the position. Follow the below instruction to set up. 1.To rotate the camera by using the live video. 2.Tap to enter the record the point section. 3.Tap "Save" you're finished.
The APP allows users to have access to live video. User can take snapshot image(s) and record the live video. If you’re using the indoor model, you can also choose the color tone according to the lighting condition. By default, the APP applies the ‘indoor’ option with warm-yellow color tone for the indoor models. You can also choose the ‘outdoor’ option in the advanced setting for cool-white color tone if it best fits your viewing environment. It is not necessary to change this setting for outdoor models.
VIEWING YOUR SNAPSHOTS For iOS Your snapshots will be named with the time stamp and saved into the Camera Roll location of your mobile device. For Android Your snapshots will be named with the time stamp and saved into the Photo Gallery > snapshot folder on your mobile device. PLAYBACK YOUR VIDEOS The recorded video file(s) on your camera is automatically saved to the memory card inserted in your camera. You can remotely access the file(s) for playback via your mobile device.
Tap EVENT LIST icon and the Date-Time filter would appear. User may define the period for system to display all available recorded file(s) for playback. VWQN= ^ j ` ~ ê ê á Éê 20160315023316.mp4 NMMB During the playback, you can tap the PAUSE icon to pause / resume the video, MUTE to deactivate/activate the audio function and GO BACK icon to return to the event list section. You may also review recorded video file(s) with your PC. For best performance, please use “Free Video Converter” from http://www.
This function helps user to easily transfer the recorded file(s) from the memory card. It is strongly suggested to download the file(s) at your home Wi-Fi network (WLAN), meaning the mobile device(s) is connecting to the same Wi-Fi router as the camera. Minimum bandwidth requirment is 1Mbps (upload/ download). Download process may be force stopped if the bandwidth becomes too slow and cannot continue. Note: For iOS system, please use "Oplayer Lite" APP for playback downloaded video files(s).
To Download / Delete the video file(s) in the EVENT LIST section, please follow the steps below: DOWNLOAD Long press the video clip to download the file onto your movbile device. Note: During the download process, system will stop both the live view and recording functions. APP will automatically inform any user accessing the camera that the systemis busy and the connection has been terminated.
MAIN PAGE OVERVIEW The MAIN PAGE section offers user an overview for all registered camera(s), including camera status (connected/disconnected). User can quickly access the camera(s) in the list. When multiple cameras are registered, scroll down to locate the registered camera for access. (iOS) (Android) ADD CAMERA The ADD CAMERA icon allows you to register additional camera(s) to the system. The system supports up to 3 concurrent user connections. 1.
4. Enter the default password 123456 in the Security Code column. (iOS) (Android) 5. Click SAVE to complete the camera settings. The APP attempts toestablish camera connection. Once the camera is successfully connected, the “Connected” status will be shown on the left upper corner. 6. Repeat step 2 to 5 to add more cameras.
In the CAMERA SETTING section you will allow to (1) configure system setting, (2) unregister camera from the APP and (3) enter event list for recorded video file(s) playback. Tap the CAMERA SETTING icon to enter/exit CAMERA SETTING. Tap the CAMERA SETTING icon. The following icons appear on the panel. (iOS) (Android) Tap the ADVANCED SETTING icon to setup camera configuration. (Please refer to "Advanced Setting" for detail). Tap the DELETE icon to remove the camera connection.
SETUP PIN LOCK (iOS) (Android) If you enable PIN Lock, the user will be asked to enter the PIN code when you launch the APP. 1. Enable the “Enable lock when starting” function. Then enter your PIN code. 2. Confirm your PIN code again. Note: If you forgot your PIN code, please uninstall the APP and reinstall it on the mobile device. NOTIFY (PUSH NOTIFICATION) The C794IP camera supports motion detection function.
For Android If you want to enable/disable it, please follow the steps below. Note: The internet connection and wireless network interference may influence the performance of push notification service. ABOUT APP/API Version Info Tap the ABOUT icon to check the APP Version when necessary. (iOS) (Android) Note: The internet connection and wireless network interference may influence the performance of push notification service.
ADVANCED SETTING This chapter explains the advanced settings for administrator. Administrator is the one who owns the administration password and has the full control to the C794IP camera. The administrator can access all C794IP functions and settings, while general users can receive the surveillance images for live view/screen capture/video recording and may not manage the camera settings. Admin Password The security code required to enter Advanced Setting for system setting management.
ADMIN PASSWORD The Admin Password is a specific security code for administrator to change the advanced settings. The default admin password is 123456. Please use this function to change the default admin password into your personal admin password. For the protection of your system configuration, every time you change the advanced settings, you need to enter the admin password. Please change the admin password periodically.
VIDEO SETTINGS This section allows you to configure the video quality and environment mode. Video Quality The Video Quality setting section allows you to adjust the quality of the video streaming. By selecting better video image will allow you to view high resolution image. By selecting better streaming will allow the video to display more smoothly (quality depend on local internet environment). Only select better image when you have sufficient bandwidth and updated mobile device(s). Please refer to P.
Siren During This section allows you to setup siren time of the camera. There are 3 mode time setup you are able to select. WI-FI SETTING The Wi-Fi setting allows you to choose the wireless connection and setup the Wi-Fi environment. When you tap the “Manage Wi-Fi network” button, the system automatically scans the nearby network and shows the available Wi-Fi routers in the drop-down list. Choose the appropriate Wi-Fi router and enter the Wi-Fi router password if necessary.
MOTION MASK This fuction allows you quickly select motion mask from 3 default model. In addition to, the user is able to tap screen which area you don’t want to be detected. 1 2 1. Tap the area where you don’t want to detect the motion. 2. 3 icons for quick tapping of bar area. 3. Reset button. 4. Save setting. 3 4 TIMESTAMP This section allows you to change the time stamp background color. And drag and drop where you want to place the time stamp. 1 1.
EMAIL SETTING The email setting allows you to configure the email environment, email account and password. Gmail account is suggested. Click the “Use SSL” check box will transmit the data in encryption. This setting requires the Simple Mail Transfer Protocol (SMTP) configuration. Most ISPs use the SMTP method to transfer outbound mail via the internet. Only use the SMTP that supports SSL. Gmail Setting (suggested) SMTP Server smtp.gmail.
SDCARD SETTING Formatting your memory card will ERASE all the data from it and you will not be able to get the data back. Please back up your video files BEFORE formatting the memory card. Note: The system is optimized to Class 10 memory card. Memory card with lower specification will decrease the recording and playback function efficiency. During format process, all recording & viewing will stop until format process completes.
TROUBLE SHOOTING IF SOLUTION The APP can not find the camera ‧ Make sure your network supports the DHCP protocol. ‧ Make sure the camera and your mobile device connect to the same Wi-Fi router for the first setting. ‧ Make sure the Wi-Fi router is activated. ‧ Make sure the camera is properly powered on. ‧ Use the “ADD CAMERA” function to manually add the camera. Wi-Fi router is not shown in the drop down list ‧ Make sure SSID broadcasting function is enabled in the WiFi router.
The APP can not record any video clips ‧ Make sure the SD card has been correctly inserted ‧ Make sure the motion detection function has been enabled. (please refer to the Sensitivity Setting section). ‧ Please format the SD card when it is used for the first time (please refer to the SD Card Format section) ‧ Make sure you are using Class 10 rated memory card. Email alert is not working ‧ Make sure the email alert function is enabled (please refer to the Email Alert section).
PRODUCTION SPECIFICATION Networking Parameter Wireless Technology IEEE 802.
STORAGE MEDIA MANAGEMENT Micro SD Card Capacity (Class 10) Event Minutes 8G 400 180 32G 1600 320 64G 3200 760 128G 6400 1440 CAMERA SIREN TEST REPORT Siren Volume Piezo Siren distance 1 Meters Piezo Siren distance 0.1 Meters 0 (Max) 74.9dB 92.9dB 1 72.5dB 90.5dB 2 67.5dB 87dB 3 62.5dB 79.5dB 4(Min) 51.6dB 68dB Slient / / * The test in progress under environment noise 48.5dB.
APPENDIX: COMPATIBLE LIST WiFi Compatible Router List Brand Product Name ASUS RT-N53 BUFFALO WIR-HP-C300NH2 BUFFALO WZR-HP-G450 Cisco ERT120 D-Link DIR-816L Huawei WSR20 INTELBRAS WRN300 NETGEAR Wndr3700v4 NETGEAR WGR614 Tenda FS395 TP-link TL-WR941N 35
