User manual

ManualsBrandsSMART ManualsSAT Reception (DVB-S)DVB-S2 & DVB-T receiver combo Skyter/Jaxter 3D Recording function, Multi tuner, USB (front), Card reader, Linux, C

1. Contents

1. Contents................................................................................................................................................................ 1

2. Important safety instructions ................................................................................................................................ 2

3. General Information .............................................................................................................................................. 3

4. Delivery contents .................................................................................................................................................. 3

5. Description ............................................................................................................................................................ 3

5.1. Front panel .................................................................................................................................................. 3

5.2. Rear panel ................................................................................................................................................... 3

5.3. Card reader ................................................................................................................................................. 4

5.4. CI interface .................................................................................................................................................. 4

5.5. Remote control ............................................................................................................................................ 5

6. Installation (Getting started) ................................................................................................................................. 6

6.1. Connecting receiver to Antenna, TV Set, Multichannel Audio System ...................................................... 6

6.1.1. Connecting to satellite and terrestrial antenna .................................................................................. 6

6.1.2. Satellite setup .................................................................................................................................... 8

6.1.3. Terrestrial antenna setup ................................................................................................................... 9

6.1.4. Connecting to TV-set and Multichannel Audio System ..................................................................... 9

6.1.5. Connecting to the Network .............................................................................................................. 11

7. Receiver setting up ............................................................................................................................................. 12

7.1. Switching on .............................................................................................................................................. 12

7.2. Main menu ................................................................................................................................................. 12

7.3. Channel search ......................................................................................................................................... 13

7.4. Channel editor ........................................................................................................................................... 15

7.5. Favorite manager ...................................................................................................................................... 16

7.6. Electronic program guide .......................................................................................................................... 17

7.7. Media player .............................................................................................................................................. 18

7.8. Recordings ................................................................................................................................................ 19

7.8.1. Schedule .......................................................................................................................................... 19

7.8.2. Records ............................................................................................................................................ 20

7.9. System settings ......................................................................................................................................... 21

7.9.1. Language ......................................................................................................................................... 21

7.9.2. Record options ................................................................................................................................. 22

7.9.3. CI & CAS .......................................................................................................................................... 22

7.9.4. Parent menu .................................................................................................................................... 22

7.9.5. System functions .............................................................................................................................. 23

8. Receiver Control ................................................................................................................................................. 24

8.1. Channel switching ..................................................................................................................................... 25

8.2. Volume control .......................................................................................................................................... 25

8.3. Time shift ................................................................................................................................................... 26

8.4. Selection of audio track and subtitles ....................................................................................................... 26

8.5. Television, radio ........................................................................................................................................ 26

8.6. Recordings ................................................................................................................................................ 26

8.7. Channel list ................................................................................................................................................ 26

9. Technical Specifications ..................................................................................................................................... 27

Summary of content (27 pages)

PAGE 1
. 1. 2. 3. 4. 5. 6. 7. 8. 9. 1 Contents Contents................................................................................................................................................................ 1 Important safety instructions ................................................................................................................................ 2 General Information .................................................................................................................
PAGE 2
. Important safety instructions This symbol indicates dangerous voltage inside the product that presents a risk of electric shock or personal injury. This symbol indicates important instructions accompanying the product.                           Please read this manual carefully before using this product. Before connecting the AC power cord to the outlet, make sure the voltage designation of the digital receiver corresponds to the local electrical supply.
PAGE 3
. General Information Skyter 3D HD receiver enables receiving television and radio programs in satellite DVB-S/S2 and terrestrial DVB-T standards. The device can be used together with an analogue or digital TV-set, audio amplifiers, home network routers and other home devices. Skyter 3D HD is able to receive “DVCrypt” system encoded channels. 4. Delivery contents - DVB-S/S2 and DVB-T digital receiver Skyter 3D HD - Remote control - HDMI cable - User’s setup Guide 5.
PAGE 4
9. Power button 10. Power cable 5.3. 1. 2. 5.4. 1. 2. Card reader The card reader is integrated into the receiver and enables to decode the channels encoded by the “DWCrypt” system. The channel cards are to be inserted into the card reader with the contact chip placed down. CI interface CI interface slot is integrated into the receiver and enables to decode the channels using external CI module. The CI module is to be inserted into CI slot.
PAGE 5
.5. Remote control 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. Fig. 3 Remote control 23. 24. 25. 5 MUTE Press to turn the volume off STANDBY Press to switch the receiver on / off (standby mode) . 0-9 Number buttons. Press to select TV channels, radio channels or menu options Freeze/Pause Press to stop / play the picture in time shift mode. ASPECT RATIO Press to change aspect ratio to 4:3 or 16:9 mode Guide Press to show electronic program guide.
PAGE 6
. Installation (Getting started) Please read this manual before installing the receiver The receiver should be placed close to a TV-set or any other home devices to connect them together using the cables available in the set. The following important rules must be followed: - Do not place the receiver close to heat sources. - Do not place the receiver close to radio waves emitting devices (e.g. mobile phones) - Place the receiver in the direct access of the remote control. 6.1.
PAGE 7
Fig. 5 Satellite LNB configuration During satellite dish LNB and cables installation you can easily check the signal and the list of the channels available on the selected frequency by entering test transponder parameters into the Test transponder section in the Satellite LNB configuration window. Then move the cursor on the “check signal” line and the STB starts tuning on the test transponder parameters. Fig.
PAGE 8
Fig. 7 Satellite LNB configuration, programs quick scan 6.1.2. Satellite setup Before start the program search, add the satellite of you dish system installation, you plan to search the program on. MENU>Settings>System setting>Antenna setup>Satellite setup. You can press green button and select satellite from the list. Then insert the satellite dish installation parameters (LNB frequency type, Diseq port or none, frequency control).
PAGE 9
Fig. 9 Adding a new satellite 6.1.3. Terrestrial antenna setup Terrestrial antenna is connected to RF IN input. If your antenna is equipped with the amplifier (the so-called active antenna), Skyter 3D HD can supply voltage to power it. It is selected by MENU>Settings>System setting>Antenna Setup>Terrestrial antenna setup>Antenna power. The supply voltage is 5volt and 100mAmp current.
PAGE 10
Fig. 12 Connecting to a TV-set and Multichannel Audio System If a user does any changes in MENU>Settings>System setting>TV out settings>HDMI video, he needs to press APPLY button to get the immediate effect. If AUTO EDID option is selected ON, the resolution and frame rate selected will be used by the receiver as the initial setting mode only. If AUTO EDID option is selected OFF, the resolution and frame rate selected will be used by receiver permanently. Fig.
PAGE 11
that the receiver will deliver selected audio track in decoded stereo mode on selected output. Due to limited number of audio codecs integrated, not all audio signals will have audio signal in Decoded stereo PCM mode. You can select HDMI Audio out on MENU>Settings>System setting>TV out settings>HDMI audio and S/PDIF out MENU>Settings>System setting>TV out settings>S/PDIF separately. Fig. 14 TV settings and HDMI audio configuration 6.1.5.
PAGE 12
Fig. 16 Network connection menu In case 3G modem is attached to USB port, the PPP(modem) line will appear on the network list. Pls note, that a modem can be attached only to rear USB ports due to power requirement. Both rear USB ports can supply 1Amp current and Front USB port can supply only 0.5Amp. By selecting PPP connection you can also scan, connect and change the available option for 3G/GSM connection. Pls note, that not all types of modems are supported by the system software.
PAGE 13
Fig. 17 Main menu 7.3. Channel search After a new satellite is added, you can search programs on it. For automatic satellite search MENU>Settings>Channel search>Satellite Auto search, the receiver requires the list of transponders on the selected satellite. Thus, during automatic satellite search the receiver will search channels according to the transponder list only. You can add new transponder data, save them, edit them or delete them on MENU>Settings>Chanel search>Satellite transponders. See Fig 18.
PAGE 14
Fig. 19 Satellite auto search MENU>Settings>Channel search>Satellite Manual search searches the channels on the selected transponder by entering it manually See Fig 20. The tuner will be loaded by all tune parameters only when you move the cursor to the Level position. The search options are the same as for the auto search. Fig. 20 Manual search For Terrestrial channels search the Terrestrial antenna is needed to be plugged in first.
PAGE 15
Fig. 21 Terrestrial search As soon as the search is finished, the list of the programs is displayed in the programs extract window. See Fig 22. Fig. 22 Channels search When search is finished, press red button to save search results or changes, or press EXIT button to exit from the search window without saving search results or changes. In the latter case, pop up window “Waiting…” will be displayed on the TV screen.
PAGE 16
As soon as the programs search is finished, the channels are displayed in the sequence they are transmitted by a broadcaster. Press the red button Sort on the remote control to sort the channels according to the offered criteria, p The sorting criteria query will be displayed on the screen. Press  /  buttons to select the desired option. Press OK button to confirm your choice. If you want to lock the selected channel, press the green button Lock on the remote control.
PAGE 17
Fig. 24 Favorite editor This editor allows to add channels in the channel list according to four of default lists: News, Movie, Sport, Other. Alternatively you can also add new lists (max 10 in total ) or edit the name of any list. You can also delete any newly added lists except the four defalt ones. E.g. You‘d like to add ProSiben HD and SAT.1 HD channels to the News list. Select ProSiben HD channel, then select SAT.
PAGE 18
Fig. 25 Electronic program guide The background image of the channel watched at the moment and the channel list is displayed in the Electronic Program Guide (EPG) window. Programs schedule Information on the current channel is displayed in the right part of the window, and the channel list is in the left part of the window. Press  /  buttons on the remote control to select the desired channel. Press > / < buttons to switch on right/left part of the window.
PAGE 19
you can use button to search inside the played file. Search progress bar appears at the bottom of the screen. Press INFO button and see the media file information. 7.8. Recordings This menu allows to operate the current records and to schedule future records. Fig. 27 Recordings. 7.8.1. Schedule This menu allows to schedule your record tasks. Press MENU>RECORDINGS>Schedule and press OK button to enter the Recordings schedule window.
PAGE 20
Fig. 28 Recordings schedule. 7.8.2. Records This menu allows to operate with the records done by the receiver. Press MENU>RECORDINGS>Records and press OK button, Records window is open. Both ways new records (scheduled recording and immediate recording) are added in this list. Program/title - channel name and program name of a recorded content criteria. Date/time- record start time and date criteria. Duration – record duration criteria. Status: “recorded” means - recorded but not viewed.
PAGE 21
Fig. 30 Recordings, records, info 7.9. System settings This window of the main menu allows you change the receiver system settings by customizing it. To select sub menu in the System setting window, select the requested sub menu and press right button to enter it. Fig. 31 System settings 7.9.1. Language MENU>System settings>Language This function selects the user’s menu language and provides adequate sound, title and text languages. All languages can be selected separately.
PAGE 22
Fig. 32 Language 7.9.2. Record options MENU>System settings>Record option you can change options for record functionality. Continuous time shift function – “yes” means each channel changes after 5 sec system will start to record the video stream. Press left button to search recorded video. Press right button to return to real time. Time shift max file size – you can select the max size of video stream data recorder in time shift mode.
PAGE 23
program classed above that age by the broadcaster is restricted, and to turn on the menu lock. In order to change the parent menu settings, you must enter the password. Initial password is 0000. When you enter the parent menu for the first time, you must change this password. Enter a new password consisting of 4 numbers, enter them again to confirm and press “apply”. Do not forget your password. Otherwise, to unlock the menu, you will have to apply to the service companies for receiver software rewriting.
PAGE 24
In case the Internet is selected, the system boots and searches the ntp server. If the server is inaccessible, the system synchronizes the date and the time from the first selected DVB channel. The system continues checking ntp server every 10 sec, and as soon as the server is accessed the system synchronizes the date and the time from the internet again.
PAGE 25
8.1. Channel switching To turn on the desired channel enter the number of the channel assigned in the channel list pressing 0...9 buttons (7.5 Favorite manager, Ошибка! Источник ссылки не найден.), or press  /  buttons to switch the channels or use channel keys on front panel. while switching the channels, the infobar appears on the TV screen. Fig. 36 Infobar It contains the following information: 1. Name of the channel watched at the moment. 2. Type of channel: S-satellite, T-terrestrial. 3.
PAGE 26
8.3. Time shift Press FREEZE button to enter time shift mode. Picture is paused at that moment, the time shift/pause icon appears on the screen. Press FREEZE again and video is playing again with the time delay. Time shift/playback icon will appear on the screen. To see the time delay length press INFO. The search line appeas on the screen. Use  / keys to move inside the time shifted video. 8.4.
PAGE 27
9. Technical Specifications Tuner & Demodulator DVB-T: - Frequency Range: 51 MHz - 858 MHz - Input Signal Level 45 dBμV – 75 dBμV - Demodulation 16/32/64/128/256 QAM DUAL Tuner & Demodulator DVB-S/S2: - Frequency Range: 950 MHz - 2150 MHz - Demodulation QPSK, 8PSK - DiSEQ control and 22Khz Video Decoding: - MPEG-2 MP@ML ISO/IEC 13818-2 - High Profile level 4.1 H.