User's Manual
Table Of Contents
- Product Registration
- Important Information
- Contents
- About Your SMART Board 600 or SBD600 Series Interactive Whiteboard
- In This Chapter
- Features
- How Does Your SMART Board Interactive Whiteboard Work?
- Included Accessories
- Optional Accessories
- Serial RS-232 Expansion Module
- The serial expansion module connects to the controller module on the back of your interactive whiteboard.
- Wireless Bluetooth Connection
- SystemOn Expansion Module
- USB Audio System
- Active USB Extension Cables
- Projector Wall-Mount (Models 680 and SBD680 only)
- SMART Board Interactive Whiteboard Floor Stand (Models 640, 660, 680 and SBD680 only)
- SMART Board Interactive Whiteboard Table Stand
- Installing and Securing Your SMART Board Interactive Whiteboard
- In This Chapter
- Environmental Requirements
- Mounting Your SMART Board 660, 680 or SBD680 Interactive Whiteboard on a Floor Stand
- Wall-Mounting Your SMART Board Interactive Whiteboard
- Securing the Pen Tray and Interactive Whiteboard
- Removing the Pen Tray
- Connecting Your Interactive Whiteboard to Your Computer
- In This Chapter
- Overview
- System Power Safety and Precautions
- Connecting with a USB Cable
- Installing SMART Product Drivers
- Connecting Using the Optional RS-232 Serial Expansion Module
- Connecting with the Wireless Bluetooth Connection Option
- Configuring Your Computer Settings
- Orienting Your Interactive Whiteboard
- Connecting a Guest Laptop
- Connecting Multiple Interactive Products
- Using and Maintaining Your SMART Board Interactive Whiteboard
- Troubleshooting Your SMART Board Interactive Whiteboard
- In This Chapter
- Adjusting the Projected Image
- Resetting Your Interactive Whiteboard
- Troubleshooting Using the Ready Light
- Flowchart 1: Getting Started
- Flowchart 2: Ready Light Off
- Flowchart 3: Ready Light Red
- Things to try first:
- • Disconnect and then reconnect the USB cable at both ends to reset your interactive whiteboard and reestablish the link.
- • If the Ready light changes from green to red while your computer is running, the computer might become unresponsive. Restart your computer.
- • An alternating red/green light might indicate that your computer is running too many other applications or doesn’t meet minimum specifications. Reduce the load on your computer by closing unnecessary applications, or replace it with a more powe...
- Things to try first:
- Flowchart 4: Ready Light Flashing Green
- Flowchart 5: Ready Light Steady Green
- A steady green Ready light indicates that the controller is operating normally. If the pen tray failed or isn’t communicating with the controller, your interactive whiteboard will still operate in mouse mode. When you reset your interactive whitebo...
- Troubleshooting Tips
- Where to Find More Information
- Contacting SMART Technical Support
- Hardware Environmental Compliance
- Customer Support
- Index
19 | INSTALLING AND SECURING YOUR SMART BOARD INTERACTIVE
WHITEBOARD
If you’re installing a SMART Board
685/SBD685 or 690/SBD690 interactive
whiteboard, space your wall-mounting brackets
4" (10.2 cm) or 6" (15.3 cm) apart respectively,
and then mark the location of the ten mounting
holes on the wall.
WARNING
Use two wall-mounting brackets to install
your SMART Board 685/SBD685 or
690/SBD690 interactive whiteboard.
Using only one bracket could result in
personal injury or product damage.
3. Use the Phillips No. 2 screwdriver to secure an
included self-tapping wall anchor at each mark.
CAUTION
Do not use a hammer to secure these
anchors.
If you find it impossible to screw an anchor flush
with the wall, you might have encountered a
stud. If this is the case, you don’t need to use
an anchor in this location. The stud will provide
adequate support for the screw that secures the
bracket to the wall.
NOTES
– For a concrete wall, drill holes at the marks, and insert concrete anchors
(not included) into the holes.
– If necessary, stand on a stepladder so that you’re able to secure
these wall anchors flush to the wall.
4. Using the screwdriver, secure the wall-mount
bracket to the self-tapping wall anchors with the
included screws.
5. With the help of another person, temporarily
hang your interactive whiteboard on the center
of its wall-mounting bracket.
685/SBD685: 4" (10.2 cm)
690/SBD690: 6" (15.3 cm)