User's Manual
Table Of Contents
- Product Registration
- Important Information
- Contents
- About Your SMART Board 600 or SBD600 Series Interactive Whiteboard
- In This Chapter
- Features
- How Does Your SMART Board Interactive Whiteboard Work?
- Included Accessories
- Optional Accessories
- Serial RS-232 Expansion Module
- The serial expansion module connects to the controller module on the back of your interactive whiteboard.
- Wireless Bluetooth Connection
- SystemOn Expansion Module
- USB Audio System
- Active USB Extension Cables
- Projector Wall-Mount (Models 680 and SBD680 only)
- SMART Board Interactive Whiteboard Floor Stand (Models 640, 660, 680 and SBD680 only)
- SMART Board Interactive Whiteboard Table Stand
- Installing and Securing Your SMART Board Interactive Whiteboard
- In This Chapter
- Environmental Requirements
- Mounting Your SMART Board 660, 680 or SBD680 Interactive Whiteboard on a Floor Stand
- Wall-Mounting Your SMART Board Interactive Whiteboard
- Securing the Pen Tray and Interactive Whiteboard
- Removing the Pen Tray
- Connecting Your Interactive Whiteboard to Your Computer
- In This Chapter
- Overview
- System Power Safety and Precautions
- Connecting with a USB Cable
- Installing SMART Product Drivers
- Connecting Using the Optional RS-232 Serial Expansion Module
- Connecting with the Wireless Bluetooth Connection Option
- Configuring Your Computer Settings
- Orienting Your Interactive Whiteboard
- Connecting a Guest Laptop
- Connecting Multiple Interactive Products
- Using and Maintaining Your SMART Board Interactive Whiteboard
- Troubleshooting Your SMART Board Interactive Whiteboard
- In This Chapter
- Adjusting the Projected Image
- Resetting Your Interactive Whiteboard
- Troubleshooting Using the Ready Light
- Flowchart 1: Getting Started
- Flowchart 2: Ready Light Off
- Flowchart 3: Ready Light Red
- Things to try first:
- • Disconnect and then reconnect the USB cable at both ends to reset your interactive whiteboard and reestablish the link.
- • If the Ready light changes from green to red while your computer is running, the computer might become unresponsive. Restart your computer.
- • An alternating red/green light might indicate that your computer is running too many other applications or doesn’t meet minimum specifications. Reduce the load on your computer by closing unnecessary applications, or replace it with a more powe...
- Things to try first:
- Flowchart 4: Ready Light Flashing Green
- Flowchart 5: Ready Light Steady Green
- A steady green Ready light indicates that the controller is operating normally. If the pen tray failed or isn’t communicating with the controller, your interactive whiteboard will still operate in mouse mode. When you reset your interactive whitebo...
- Troubleshooting Tips
- Where to Find More Information
- Contacting SMART Technical Support
- Hardware Environmental Compliance
- Customer Support
- Index
7| ABOUT YOUR SMART BOARD 600 OR SBD600 SERIES INTERACTIVE
WHITEBOARD
SystemOn Expansion Module
The SystemOn expansion module brings
your projector out of standby mode, and
has indicators showing SystemOn
component activity.
Access two additional features through
the interface’s Advanced tab:
• Automatic Logoff—SystemOn logs you off
of your computer when the system enters
standby mode.
• Display Mode Detection—SystemOn
determines the projector state: normal or
standby mode.
Components of the SystemOn Expansion Module
The SystemOn expansion module kit contains:
• a control panel module that snaps into the pen tray’s
expansion slot.
• a projector controller and an activity sensor unit
that provides power to your projector and relays
information between your computer, projector and
interactive whiteboard’s pen tray control panel.
• a 16' 5" (5.0 m) USB A/B cable to connect your
projector controller to your computer.
• a 16' 5" (5.0 m) RJ45 Cat 5 cable to connect
your projector controller to your interactive
whiteboard’s SystemOn control panel.
• a CD containing the most recent Windows® version of SystemOn software.
• a North American or United Kingdom power adapter to connect your projector’s
power cord to the projector controller and activity sensor.
For more information about installing, using and troubleshooting the SystemOn
expansion module, see the SystemOn Expansion Module Installation Guide,
document 1330
at www.smarttech.com/support.