User's Manual

T O PR OGR AM FOR USE W I T H G AR AGE DOOR R E C E I V E R :
The Garage Door R eceiver allows the use of the same GTO remote transmitter for both the gate opener
and the garage door opener and works in conjunction with dual and triple transmitters (Figure E).
1. R emove the Transmitter Cover
Remove the access cover from the front of the transmitter by sliding the cover away from the top of
the transmitter. This will expose the battery and the dip switches. The code can now be changed using
a small screwdriver.
2. R emove the Garage Door Receiver Cover
Use a small screwdriver or knife to remove small door on top of receiver to gain access to coding
switches.
3. Setting the Transmitter Code (Figure G)
In the transmitter there are eight (8) dip switches,
each of which can be placed in three different
positions (+,0,-). DO NOT set all switches in the
same position, such as all +,all -, or all zeros.
WAR NI NG : No other adjustments should be
made inside the transmitter.
3. Setting the R eceiver Code
In the receiver, there are nine (9) dip switches.
Set the first eight switches in the receiver so that
they exactly match the eight switch settings on
the transmitter (Figure G).
Set the ninth dip switch to correspond with the transmitter button that you wish to use to open garage
door. Each transmitter button corresponds to a (+, 0, or -) setting (Figure H).
On the Dual Transmitter, the L eft button has a (+) setting, and the R ight button has a setting of (0).
On the Triple Transmitter, the L eft button has a (+) setting, the middle button has a setting of (0), and
the Right button has a setting of (-).
For example, if you wish to use the R ight button on the Dual Transmitter to open your garage, you
would set the ninth dip switch on the receiver to (0). Be sure not to use the same transmitter button
that you selected to activate the gate operator. For example, on a Dual Transmitter, if you set the L eft
Button to open your gate, you would use the R ight Button to open your garage door.
K
P
amp
Q@R@S@T@U@V@W@X@@
K
P
Q@R@S@T@U@V@W@X@Y@
HKI HPI HKI HPI
H
½
I
„”™“Œššˆ˜@sžŒš†‹ˆ™ rˆ†ˆŒœˆ˜@sžŒš†‹ˆ™
Figure G
Figure H
Please note: verification of the warranty period
requires copies of receipts or other proof of
purchase. Warranty can not be honored without
proof of purchase. Please retain these records.
GTO, Inc. ¥ 3121 Hartsfield R oad ¥ Tallahassee, Florida, USA 32303
Telephone GTO Sales: 1-800-543-GAT E (4283) or (850) 575-0176 ¥ Fax (850) 575-8912
or GTO Technical Service: 1-800-543-1236 or (850) 575-4144 ¥ Fax (850)575-8950
www.gtoinc.com
I nstructions for G ate Operator R adio C ontrols:
Single E ntr y Transmitter, K eychain M ini Transmitter,
Dual & Triple E ntry Transmitters
1. R emove the Transmitter Cover
Remove the access cover from the front of the transmitter by sliding the
cover away from the top of the transmitter (Figure A). This will expose the
battery and the dip switches. T he code can now be changed using a small
screwdriver.
2. Setting the Code
There are nine (9) dip switches, each of which can be placed in
three different positions (+,0,-). DO NOT set all switches in the
same position, such as all +, all -, or all zeros (Figure B).
W A RNING: No other adjustments should be made inside the
transmitter.
Now that your have selected your personal code, reassemble the
transmitter.
3. Commit the Code to Memory in Control Board
Remove operator control box lid. L ocate the L EARN TRANSMITTER or
S5 button on the control board:
A. Turn the control box power switch OFF.
B. While pressing the L EARN TRANSMITT ER or S5 button on the
control board turn the control box power switch ON and press the
TR ANSMITTER button.
C. R elease the L EA RN TRANSMITTER or S5 button after approxi-
mately 5 seconds.
D. Continue to hold the TR ANSMITT ER button until the gate begins to move. The new
TR ANSMITTER code is now stored in the control board memory.
4. Using your transmitter
The transmitter can either be hand held or mounted on the sun visor of your vehicle. To activate your
gate operator, simply depress your transmitter button until the gate begins to move.
NOT E : If the red light on the transmitter is dim or flickers when the transmitter button ispushed, the
transmitter battery may be weak. R eplace when necessary with a 12 Volt battery.
C AUT I ON: E ach transmitter is set to a factory preset code. I t must be
changed to safeguard against unauthorized or unwanted oper ation.
I NST R UCT I ONS FOR SI NG L E E NT R Y T R ANSMI T T E R
R ead the following instructions thoroughly before using transmitter.
K
P
amp
Q@R@S@T@U@V@W@X@Y@
Figure A
Figure B
lˆ„˜”@t˜„”™“Œššˆ˜
•˜@sU@b›šš•”
F C C R egulation: T his device complies with FC C Rules Part 15. Operation is subject to the following two conditions:
1) This device may not cause harmful interference. 2) This device must accept an interference that may cause an
our control.
aundesired oper
tion. WA RNING: Changes or modifications to this unit not expressly approved by the party
Such modifications could
responsible for compliance could void the user's authority to operate the equipment.
                                                                                                   
Tr
ansmitter distance may vary due to cir
cumstances beyond
void the user's authority to operate the equipment.