AT42QT2120 Datasheet
Table Of Contents
- Features
- 1. Pinouts and Schematics
- 2. Overview
- 3. Wiring and Parts
- 4. I2C-compatible Communications (Comms Mode Only)
- 5. Setups
- 5.1 Introduction
- 5.2 Address 0: Chip ID
- 5.3 Address 1: Firmware Version
- 5.4 Address 2: Detection Status
- 5.5 Addresses 3 – 4: Key Status
- 5.6 Address 5: Slider Position
- 5.7 Address 6: Calibrate
- 5.8 Address 7: Reset
- 5.9 Address 8: Low Power (LP) Mode
- 5.10 Address 9 – 10: Toward Touch and Away from Touch Drift (TTD, ATD)
- 5.11 Address 11: Detection Integrator (DI)
- 5.12 Address 12: Touch Recal Delay (TRD)
- 5.13 Address 13: Drift Hold Time (DHT)
- 5.14 Address 14: Slider Options
- 5.15 Address 15: Charge Time
- 5.16 Address 16 – 27: Detect Threshold (DTHR)
- 5.17 Addresses 28 – 39: Key Control
- 5.18 Addresses 40 – 51: Pulse/Scale for Keys
- 5.19 Address 52 – 75: Key Signal
- 5.20 Address 76 – 99: Reference Data
- 6. Specifications
- Appendix A. I2C-compatible Operation
- Associated Documents
- Revision History
9634E–AT42–06/12
Headquarters International
Atmel Corporation
1600 Technology Drive
San Jose, CA 95110
USA
Tel: (+1) (408) 441-0311
Fax: (+1) (408) 436-4314
Atmel Asia
Unit 01-05 & 16, 19F
BEA Tower, Millennium City 5
418 Kwun Tong Road
Kwun Tong
Kowloon
HONG KONG
Tel: (+852) 2245-6100
Fax: (+852) 2722-1369
Atmel Munich GmbH
Business Campus
Parkring 4
D- 85748 Garching bei München
GERMANY
Tel: (+49) 89-31970-111
Fax: (+49) 89-3194621
Atmel Japan
16F Shin-Osaki Kangyo Building
1-6-4 Osaki
Shinagawa-ku, Tokyo 141-0032
JAPAN
Tel: (+81) (3) 6417-0300
Fax: (+81) (3) 6417-0370
Touch Technology Division
1560 Parkway
Solent Business Park
Whiteley
Fareham
Hampshire
PO15 7AG
UNITED KINGDOM
Tel: (+44) 844 894 1920
Fax: (+44) 1489 557 066
Product Contact
Web Site
www.atmel.com
Technical Support
touch@atmel.com
Sales Contact
www.atmel.com/contacts
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND
CONDITIONS OF SALE LOCATED ON THE ATMEL WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED
OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS
INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to
update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive
applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
© 2012 Atmel Corporation. All rights reserved. Atmel
®
, Atmel logo and combinations thereof, Adjacent Key Suppression
®
, AKS
®
, QTouch
®
and
others are registered trademarks, others are trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be
registered trademarks or trademarks of others.