User's Manual

Safety and handling
The Urgegas device contains four AAA
batteries.
CAUTION: Batteries may explode or leak and
cause injury, if disposed on fire, recharged,
mixed with a different battery type,
disassembled or inserted backwards. Do not
leave batteries in your device if you suspect it
will not be used. Do not use old and new
batteries at the same time or batteries of
different brands.
Maintain a minimum of 12 inches (30cm)
between your medical devices and Urgegas.
Stop using Urgegas devices immediately if you
suspect it is interfering with any medical
devices.
PRECAUTIONS BEFORE
INSTALLATION
•Use caution when using this
product.
•Keep out of reach of children.
1. If you want better precision of your propane
gas levels please use a level tool to align your
tank.
1. Download the Urgegas mobile app.
Images are illustrative and may vary from actual product, © 2022 Urgegas. Urgegas
logo are trademarks or registered trademarks of Urgegas.
Apple and the Apple logo are registered trademarks of Apple Inc. Apple is a
trademark of Apple Inc., registered in the U.S. and other countries and regions. App
Store is a service mark of Apple Inc., registered in the U.S. and other countries and
regions. Google Play and the Google Play logo are trademarks of Google LLC.
Urgegas is an ultrasonic device to monitor your
propane tanks levels.
Do not remove the silicone
cover unless you are
planning to attach your
sensor to your propane tank
permanently.
URGEGAS - ULTRASONIC GAS TANK LEVEL METER
Model: URGEGAS-I
Size: Thickness = 0.55”; width = 2.6”; length = 6.2”
Weight: 124.5g (without battery)
Battery: AAA x4
Supported temperature: (5 °F ≤ T ≤ 120 °F)
Wi-Fi connectivity: 2.4 GHz (only)
2. Dispense equals amount of glue from each
tube and mix throughly. This should be enough
to cover the inner top portion of the sensor. Do
not mix large amounts of glue at once. Do not
use more than 30 seconds to mix the glue.
Getting started
1. First remove the silicone cover from the
sensor.
4. Mount the sensor to the place that you
perviously marked on the bottom of your
propane tank. The glue will cure in 5-10
minutes at 70°F (21°C). Colder temperatures
may required additional time. The glue will
reach full strength within 60 minutes.
5. After the glue has cured in Step 4, you can
mount the Urgegas device to the sensor.
6. Perform your test installation using your
mobile app.
3. Immediately apply the mixed glue to the top
surface of the sensor’s inner circle.
Front view
SUMMARY
Back view
Notes
MUST READ USER MANUAL
INDEX
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
WARNING: Changes or modifications not
expressly approved by the party responsible
for compliance could void the user's authority
to operate the equipment.
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation.
GLUE PRECAUTIONARY STATEMENT: Do not
use the glue in the package if you are allergic
to Acrylic Glue. Use only outdoors or in a
well-ventilated area. Do not breathe gas,
fumes, mist, spray or vapor. Wear protective
gloves, protective clothing, eye, and face
protection. Do not drink, smoke or eat when
using this product. Wash your hands
thoroughly after handling.
Exposure in an enclosed or
poorly-ventilated area may be very harmful.
Included in this package are two tubes of
adhesive: modified acrylate AB glue
series-adhesives and instant adhesives series.
These products are produced by Guangdong
Evergrande New Material Technology Co., Ltd.
in China. READ WARNINGS LABELS ON THE
ADHESIVE TUBES BEFORE USE.
WARNING DISCLAIMER
BATTERIES
CAUTION: Batteries may explode or leak and
cause injury, if disposed on fire, recharged,
mixed with a different battery type,
disassembled or inserted backwards.
Do not leave batteries in your device if you
suspect it will not be used for long periods of
time. Do not use old and new batteries at the
same time, or batteries of different brands.
GLUE
Any bad usage of the Urgegas contents are
under the user's responsibility.
Glue in this package MAY PRODUCE
ALLERGIC SKIN REACTION. Do not swallow.
Do not get in your eyes, skin or any part of
your body. This could cause injury or death.
If for any reason you have a negative reaction
to the glue, immediately seek medical
attention.
The tubes of AB glue is part of the permanent
installment of the Urgegas device product
ONLY. Its usage is ONLY for the Urgegas
sensor permanent installation, which takes no
more than 10 minutes. The AB tubes contained
in this package are only and strictly for gluing
the sensor to a propane tank surface. Please
use CAUTION when doing so.
KEEP OUT OF THE REACH OF CHILDREN.
Please READ CONTENTS ON THE AB GLUE
TUBES COVER before opening to avoid any
possible allergic reaction.
Acrylate AB glue series-adhesives can be
toxic, flammable and irritant. Keep away from
heat or ignition sources.
When installing the sensor under a propane
tank, do it in a well ventilated place.
Close the glue right after usage. Adhesive has
a pungent smell.
GLUE MAY CAUSE DROWSINESS OR
DIZZINESS. CAUSES SKIN IRRITATION. IT
CAN CAUSES EYE IRRITATION. MAY CAUSE
RESPIRATORY IRRITATION. CAUSES
DAMAGE TO BLOOD AND LIVER THROUGH
PROLONGED OR REPEATED EXPOSURES.
According to the AB adhesive company, the
product has passed the ISO9001 Quality
Management System Certification and
ISO14001 Environmental Management System
certification.
IF INHALED: Remove person to fresh air and
keep comfortable for breathing. Call a POISON
CENTER or medical emergencies. If skin
irritation occurs, wash thoroughly with water
and seek medical attention immediately.
Make sure that your propane tank is off.
The tank’s valve should be turned off to avoid
any propane gas leak before installing your
Urgegas device. ALWAYS MAKE SURE THAT
YOUR PROPANE TANKS DO NOT HAVE ANY
GAS LEAKS.
Avoid any friction when installing your device.
Friction could be dangerous if there is a gas
leak. This could cause a spark and result in a
explosion resulting in death or serious injury.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Consult the dealer or an experienced radio/TV
technician for help.
FCC Radiation Exposure Statement:
The device has been evaluated to meet general
RF exposure requirement. The device can be used
in portable exposure condition without restriction.
FCC STATEMENT
ADHESIVE ACRYLIC
GLUE WARNING
Please visit our website at
https://urgegas.com/warranty for warranty
details.
WARRANTY
DEVICE INSTALLATION
PERMANENT
ATTACHMENT
2. In the mobile app, press the add sign button
to start.
3. Turn the device on by clicking once. To learn
more about the meaning of the sounds that
your Urgegas device makes, go to your mobile
app, click on Menu Help User guide
Beeps sounds.
4. Follow the instructions in the mobile app to
get your device connected to the internet.
5. Enter your network credentials to connect
your device to the selected network.
Notes before you start
Make sure that the surface of the propane and
sensor are clean and dry.
Before opening the glue
Make sure that you are in a well
ventilated area. The glue has a
pungent smell. Do not smell it
directly. Do not swallow. Do not use
on skin, eyes, hair or any part of your
body. This could cause injury or
death. Avoid any contact. If for
any reason you have a negative
reaction to the glue, immediately
seek medical attention.
Important information
Identify the exact spot where you will glue your
sensor to the propane tank.
Using your mobile
app you can perform
a test installation to
make sure that it is
the right place to
install it before you
stick it permanently to
your tank.
Notes
Urgegas base sold separately.
Urgegas base
GETTING STARTED
2. Clean the bottom area of your propane tank
using a cleaning rag and water to avoid any
interference before placing your device.
It must be free of dust, rust, mud, water etc.
Make sure that the surface is clean and dry.
Make sure that the
device is
perfectly aligned
in the center from
the side view.
You can move it to the right or left depending
on the test installation executed using your
mobile app.
However, better results of the test installation
are usually reached when you place the
Urgegas device on the same end as the liquid
withdrawal valve.
If it is not correctly aligned, it may cause wrong
readings.
Perform a test installation through the
Urgegas mobile app to verify that your device
is placed correctly.
Mount your urgegas device to the bottom of
your tank, right in the middle. If it is not aligned
it may cause wrong readings. Ensure that the
tank’s weight is not resting on the Urgegas
device. If so, an Urgegas Base may be
required.
You should consider a permanent
attachment of your Urgegas device to the tank
only in the following cases:
1. Increased precision of the propane gas levels
is desired.
2. The tank is located in an environment that is
exposed to wind, water, dust, snow, dirt or any
other factor caused by the weather.
3. If you will not exchange your propane tank, or
your tank is stationary.
Horizontal /
Stationary propane
tanks
Cylinder / Vertical tanks
Cylinder /
Vertical tank
Horizontal /
Stationary propane tanks
Installation
Area
Power button
Silicone cover /
coupling agent
LED indicator
Batteries AAA
Battery screws
Warranty is void if
screws are removed.
URGEGAS INTRODUCTION
PRODUCT PARAMETERS
Detachable ultrasonic
sensor with magnet
Side view
Float
Urgegas introduction 05
Product parameters 06
Summary
05
Getting started 07
Device installation 10
Permanent attachment
13
FCC statement
17
Warranty
18
Warning disclaimer
19
05 06 07 08 09 10 11 12 13 14 15 16 17 18
Password
Network Name (SSID)
Urgegas devices only support 2.4 GHz WiFi
1. En
ter your WiFi credentials.
2.
Press and hold the device power butt
on
for 3 se
conds, you will hear a beep sound.
3.
Press the send button to connect.
Back
WiFi Credentials
MyNetwork-xxxxa
2019
Liquid
withdrawal
valve
Please visit
https://urgegas.com/install
for a video tutorial.