Installation Instructions
Figure 1
Figure 2
Figure 3
Figure 4
4. Install the lamp into the mounng screws, then shi the whole lamp opposite the power code side, let the key hole hold the mounng screws
ghtly.(Figure 3)
5. Install a screws on one end of the lamp to prevent the lamp from loosing and falling. Plug in the power cord to the outlet. (Figure 4)
hole distance:
Figure 1
(Figure 2)
hole distance:
locaon screws
1.Use the wood screws with hook.
2.Drill the hole for the screws on the mounng surface ,Spacing between two screws is 891mm(35inch),then install the screws.(Figure 1)
MODEL No.: Z-3200P-3
SKU No.: 3482144
SAFETY INFORMATION
NOTE: Turn off the electrical power at the fuse or circuit breaker box before installing or servicing any part of this fixture.
NOTE: Do not use or store in corrosive environment with hazardous material e.g. Sulphur, Chlorine, Phthalates, etc.
CAUTION: 1) Installation must not be made on a radiant-heating ceiling,
2)the hooks are to engage the chain only and not the electric cord.
CAUTION: TURN OFF THE MAIN POWER AT THE CIRCUIT BREAKER BEFORE INSTALLING THE FIXTURE IN ORDER TO
PREVENT POSSIBLE ELECTRIC SHOCK.
3FT LED NON LINKABLE SHOP LIGHT
891mm±1
891mm±1
3.Insert the hook of the hanging wire into the mounng hole on the ends of lamp.(Figure 2)
4.Use the zip e to aach the AC cable to the hanging wire.
5.This lamp is intended to be installed directly beneath a ceiling mounted receptacle.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This
equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by truning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation
between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
These products may represent a possible shock or fire hazard if improperly installed or attached in any way. Products should be
installed in accordance with the owners manual, curr
ent electrical codes and/or the current National Electric Code (NEC).
" SUITABLE FOR DAMP LOCATIONS" & "CONVIENT AUX EMPLACEMENTS HUMIDES"
" DO NOT SUBMERSE" & "NE PAS IMMERGER"
ASSEMBLY INSTURCTIONS - SURFACE MOUNTING
TROUBLESHOOTING
ASSEMBLY INSTURCTIONS - SUSPEND MOUNTING
1. Use provide screws
2. Drill the hole for the screws on the mounng surface ,Spacing between two screws is 891mm(35inch). (Figure 1)
3. Put the plasc anchor into the drilled hole ,then install the screws. (Figure 2)
Hanging cables
Zip tie
Screw hooks
Wall anchors
Mounting screws
BB
PACKAGE CONTENTS
HARDWARE CONTENTS Note: Hardware not shown actual size.
AA
CC
DD
BB CC
DD
EE
120 Vac 60Hz 0.34A
120 Vac 60Hz 0.34A
120 Vac 60Hz 0.34A
IMPORTANT SAFETY INSTRUCTIONS
This portable luminaire has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will
fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Never use with an extension cord unless plug can be fully inserted. Do not alter the plug.
CAUTION: Before beginning installation turn off the circuit breaker and light switch.
Figure 2
EE
AA
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-855-508-3883
Monday – Friday 9:00 a.m. – 5:00 p.m. CST
POSSIBLE CAUSE CORRECTIVE ACTION
The fixture will not light
The power is off.
Check to ensure the power
supply is on
Check to ensure the circuit
breaker is in the on posion
Check to pull the pull chain to ensure
the switch is on.
The circuit breaker is off.
The pull chain switch is off.
PROBLEM
If unable to fix any of the above issues, please consult a certified electrician.
FIVE-YEAR LIMITED WARRANTY: If, during normal use, this SMART ELECTRICIAN lighng fixture breaks or fails due to a defect in material
R
R
R
R
workmanship within five (5) years from the date of original purchase, simply bring this lighng fixture with the original sales receipt back to
your nearest MENARDS retail store. At its discreon, SMART ELECTRICIAN agrees to have the product or any defecve part(s) repaired or
replaced with the same or similar SMART ELECTRICIAN product or part free of charge, within the stated warranty period, when returned by the
original purchaser with original sales receipt. This warranty; (1) excludes expendable parts including but not limited to light fixture; (2) does not
cover damage that has resulted from abuse or misuse; and (3) does not cover any losses, labor, injuries to persons/property or costs. This
warranty does give you specific legal rights and you may have other rights, which vary from state to state.