Installation Instructions

32
Before beginning assembly, installation, or operation of product, make sure all parts are present. Compare
parts with package and hardware contents list on page 1. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts: 1-844-255-9692
Monday – Friday 8:00 a.m. – 5:00 p.m. CST.
Tools Required for Assembly (not included): Suitable Fasteners, Screwdriver, Tape Measure, Pencil, Safety
Glasses and Ladder
SAFETY INFORMATION
PREPARATION
DANGER
• Be careful not to damage or cut the jacket of the power cord during xture installation. Do not permit power
cord to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which
could cause serious injury or death from electric shock.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS (continued)
WARNING: These products may represent a possible shock or re hazard if improperly installed or attached
in any way. Products should be installed in accordance with these instructions, current electrical codes, and/or
the current National Electric Code (NEC).
WARNING: To reduce risk of re, electric shock, or injury to persons, be sure that power supply is turned o󰀨
at fuse box or circuit breaker before attempting installation or servicing of the xture. For safest operation, read
and become familiar with complete installation instructions prior to use. Pay close attention to this manual and
stay within its guidelines when using this product. This xture is suitable for dry and damp locations.
SAVE THESE INSTRUCTIONS
ADDITIONAL SAFETY MEASURES
1. To avoid electrical shock, do not turn on xture with missing or damaged lens.
2. There are no serviceable parts inside LED module.
3. LEDs emit bright light. Avoid looking directly at the light source.
4. Do not alter the power cord in any way.
5. Do not use with any other cord, cable or connector other than those provided with the xture.
6. Not to be used with a dimming circuit.
3. First, attach one hang chain to the xture using one S hook
provided. Repeat with second hang chain and second S hook
at other end of xture.
Fig. 3
4. Put each chain over the mounting hooks attached to the
ceiling and adjust the chains over the hooks as needed so that
the xture hangs level.
Fig. 4
5. Attach the power cord to the open port on the end of the xture
near the pull-chain.
Fig. 5
6. Plug power cord into ceiling outlet and use pull chain to
operate on and o󰀨 functions. Installation is complete for one
xture.
Fig. 6
7. Multiple xtures (up to six) can be linked together and powered
by one power cord. WARNING: When linking multiple
xtures, UNPLUG POWER CORD FROM OUTLET BEFORE
PROCEEDING. Follow steps 1-4 for the additional xture(s).
When using the linking cord, xtures can be up to 12” apart.
Fig. 7
1. Select a suitable location for the Shop Light that can support
its weight, and that has an outlet on the ceiling to insure that
the xture is powered properly. Determine mounting method
and obtain proper fasteners for the surface type.
Fig. 1
2. Mark two locations on the ceiling that are 40-1/4 inches apart.
and attach suitable fasteners (not included) at the marked
locations. For mounting to drywall ceilings, toggle bolt j-hooks
are recommended. For mounting to wood ceilings, standard
j-hooks are recommended.
Fig. 2
40-1/4in.
40-1/4in.
40-1/4in.
<12in.
8. Attach the linking cable to the output end of the rst
xture. Plug the other end of the linking cable into the
input end of the additional xture.
Plug the power cord back into outlet as shown in
Step 6.
Fig. 8
9. When using the integrated connector, xtures can be
connected directly from xture to xture with no space
in between. Plug one end of the xture into the other
xture using the integrated connector.
Plug the power cord back into outlet as shown in
Step 6.
Fig. 9