SI4548-US-10 Manual
Table Of Contents
- 1 Information on this Manual
- 2 Sunny Island 4548-US/6048-US
- 3 Safety Precautions
- 4 Assembly
- 5 Opening and Closing
- 6 Electrical Connection
- 7 Control Elements
- 8 Initial Start-Up
- 9 Switching On and Off
- 10 Operation
- 11 Archiving Data on an SD Card
- 12 Additional Functions
- 12.1 Load Shedding
- 12.2 Sleep Mode
- 12.3 Time-Controlled Operation
- 12.4 Overload and Short-Circuit Behavior
- 12.5 Mixed Operation with Sunny Island inverters of Different Power
- 12.6 Device Faults and Autostart
- 12.7 Automatic Frequency Synchronization
- 12.8 Time-Controlled Standby
- 12.9 Behavior in the Event of a Failure in a Three-Phase System
- 13 Battery Management
- 14 Connecting External Sources
- 14.1 Generator
- 14.1.1 Parallel Connection
- 14.1.2 Generator Start Options
- 14.1.3 Generator Operation
- 14.1.4 Manual Generator Operation
- 14.1.5 Automatic Generator Operation
- 14.1.6 Limits and Power Control
- 14.1.7 Run Times
- 14.1.8 Operation Together with PV Inverters and Wind Power Inverters
- 14.1.9 Stopping the Generator
- 14.1.10 Stopping the Sunny Island
- 14.1.11 Disturbances
- 14.2 Grid
- 14.2.1 Limits of the Voltage Range and Frequency Range
- 14.2.2 Starting the Sunny Island
- 14.2.3 Operation in the Event of Grid Failure in a Grid-Tie Backup Configuration
- 14.2.4 Backup Operation and Anti-Islanding
- 14.2.5 Grid Reconnection
- 14.2.6 Grid Operation
- 14.2.7 Grid Failure
- 14.2.8 Disturbances
- 14.2.9 Limits and Power Control
- 14.2.10 Operation Together with PV Inverters and Wind Power Inverters
- 14.3 Generator and Grid
- 14.1 Generator
- 15 Relays
- 16 Multicluster Operation
- 16.1 Communication between the Sunny Island inverters
- 16.2 Initial Start-Up of the Multicluster System
- 16.3 Switching a Multicluster System On and Off
- 16.4 Generator Operation
- 16.5 Behavior with Different States of Charge
- 16.6 Testing the Multicluster Communication
- 16.7 Automatic Frequency Synchronization
- 16.8 Updating the Firmware
- 16.9 Error Handling in the Multicluster System
- 16.10 Grid Operation
- 16.11 Generator Emergency Operation
- 17 PV Inverters
- 18 Maintenance and Care
- 19 Parameter Lists
- 20 Troubleshooting
- 21 Accessories
- 22 Technical Data
- 23 Glossary
- 24 Contact
20 Troubleshooting SMA America, LLC
204 SI4548_6048-US-TB_en-13 Technical description
19.6 Direct Access to the Parameters
19.6.1 Direct Access (600#)
Observe the information for the direct accessing of the parameters (see Section 10.3 "Direct Access
- Direct Access to the Parameters", page 82).
20 Troubleshooting
In general the Sunny Island distinguishes between events and errors.
• Events describe state changes or transient states (e.g. generator connection).
• Errors describe states that are not permitted or are only permitted up to a certain rate.
This includes warnings, failures and errors. User interaction is generally required.
20.1 Error Confirmation
If a disturbance or error occurs, the Sunny Island goes into standby.
Proceed as follows to confirm an error:
1. Remove the cause.
2. Confirm error with <ENTER>.
3. Start the Sunny Island again.
20.2 Autostart Handling
The Sunny Island has an autostart meter which counts down by 1 with every automatic start. If the
Sunny Island runs uninterrupted for over ten minutes, the autostart meter is reset to its initial value.
If another fault occurs when the autostart meter is at 0, the Sunny Island waits for ten minutes and then
attempts to restart. The autostart meter begins to run again.
The number of the autostarts allowed can be set using the "250.01 AutoStr" parameter (in standby
mode).