User Manual

15
- Press the DISPLAY button in order to switch the display to step.
- Select a scene where a new scene is to be inserted, via BANK UP/DOWN buttons. Now the
displaywill show the scene. E.g. if you want to insert a scene between scene 5 and scene 6,
press the BANK UP/DOWN buttons so that the display show STEP05.
- Press MIDI/REC to prepare inserting. Now the display will show the next scene.
- Select the bank where the scene to be inserted via BANK UP/DOWN buttons.
- Select the scene to be inserted via the SCENES buttons.
- Press MIDI/REC button to insert the scene. All leds on the panel will flash.
Deleting a scene in a chase:
- Press and hold the PROGRAM button for about 2 seconds to enter the programming mode. The
program flash will flash.
- Select the chase in which a scene will be deleted via the CHASE buttons.
- Press the DISPLAY button in order to switch the display to step.
- Select the scene to be deleted via the BANK UP/DOWN buttons.
- Press AUTO/DEL button to delete the scene All leds on the panel will flash.
DELETE A CHASE:
- Press and hold the PROGRAM button for about 2 seconds to enter the programming mode. The
program flash will flash.
- Select the chase to be deleted via CHASE buttons.
- Press and hold AUTO/DEL button and the respective chaser button to delete the chase. All leds
on the panel will flash.
DELETE ALL CHASE:
- Caution: when you select this function, all program chase will irrevocably be lost. The individual
scenes and programs are maintained.
- Switch off the device.
- Press and hold the BANK DOWN + DEL buttons, while switching on the device. All leds on the
panel will flash.
SCENE (Step)
INSERT A SCENE:
- Press and hold the PROGRAM button for about 2 seconds to enter the programming mode. The
program flash will flash.
- Select the desired chase via chase button. The respective led will be lit.
- Press the DISPLAY button in order to switch the display to step. The display will show the scenes
(steps) in the chase.
- Select the scene were the scene will be inserted with BANK UP/DOWN buttons. E.g. if you want
to insert a scene between scene 5 and scene 6, press BANK UP/DOWN buttons so that the
display will show STEP05.
- Press MIDI/REC button to prepare inserting. Now the display will show the next step (E.g.
STEP06).
- Select the bank where the scene will be inserted via the BANK UP/DOWN buttons.
- Select the scene you want to copy via SCENES button.
- Press MIDI/REC button to insert. All leds on the panel will flash.
COPY A SCENE:
- Press and hold the PROGRAM button for about 2 seconds to enter the programming mode. The
program flash will flash.
- Select the bank where the scene will be copied via BANK UP/DOWN buttons.
- Select the scene to be copied by pressing the respective SCENES button.
- Press the MIDI/REC button to prepare copying.
- Select the bank where you want to copy the scene, via the BANK UP/DOWN buttons.
- Press the desired SCENES button. All leds on the panel will flash.
DELETE A SCENE:
- Press and hold the PROGRAM button for about 2 seconds to enter the programming mode. The
program flash will flash.
- Select the bank in which a scene will be deleted, via BANK UP/DOWN buttons.
- Press and hold the AUTO/DEL button.
- Press the SCENES button corresponding to the scene to be deleted.
- Now you have deleted the scene. All leds on the panel will flash.
- All 240 DMX channels of the deleted scene will be set to 0.
DELETE ALL SCENES:
Caution: when you select this function, all programmed scenes will be irrevocably lost.
- Press and hold the BANK DOWN and PROGRAM buttons while disconnecting the device from
the mains.
- Connect the device to the mains again.
SOUND CONTROL
- Pressing the MUSIC/BANK COPY button, the Music led will be lit. When the device receives a
music signal, it will work in Sound Control mode.
- Select the bank to be sound controlled via BANK UP/DOWN buttons.