User manual

The installation may only be carried out by an approved
electrician, who is familiar with valid directives and
regulations!
Explanation of the safety warnings:
DANGER: immediate dangerous situation leading to death or severe
injuries when not avoided.
WARNING: possible dangerous situation leading to death or severe
injuries when not avoided.
CAUTION: possible dangerous situation leading to injuries or material
damage when not avoided.
In case of disregarding this manual the warranty will be void!
Pay also absolute attention the NOTES ON SAFETY on the backside!
1. INSTALL AS DIRECTED
This product serves exclusively lighting purposes and may:
 only be operated using a suitable conventional transformer, output:
12V/AC.
 only be operated when firmly mounted.
 not be exposed to strong mechanical loads or to strong contamination.
 only be installed and operated after a condition inspection if the product
is dirty or has been moistened through storage.
 not be modified or converted.
2. UNPACKING
 Consignment:
Installation pot
 Carefully take the product out of the packaging removing any transport
safeguards.
 Before disposal of the packaging material make sure that all
components of the product are removed.
WARNING
Inspect the product for loose parts inside the housing. When there are
loose parts inside the housing and these are not explicitly described the
product may not be installed or operated.

Parts that may be touched are maybe voltage-carrying. Danger of
electric shock!
3. INSTALLATION
Indication for the installer: In case you do not install a completely
supplied system (with transformer), you are considered a "manufacturer"
by the low-voltage directive. In this case you are required to ensure the
conformity of the whole system and declare it by attaching the CE-sign.
WARNING
Switch off the mains or respectively of the connection lead before doing
any works
.
 There exists mortal danger from an electric shock.
Use only accessory parts, which are supplied with the product or are
described as accessories!
 Otherwise the product or the whole installation may not be secure.
Danger for life or danger of fire may exist!
Installation place
 The product is solely suited for recessed floor installation.
 Make sure that the product is mounted on a stable, even and tilt-fixed
background.
Preparing the low-voltage (12 V) power supply
The transformer should be used up to 80 % of its capacity. The total watt
power of the connected light fittings must not exceed the power output of
the transformer. The distance between spot and transformer should be at
least 20 cm. Note the manufacturers information for the transformer.
WARNING
High currents with low-voltage installations!
 Use only heat resistant wires and clamps to avoid danger of fire.
Before installation
 Do not try to seal the product yourself, using additional silicon or another
sealant.
 DO NOT REMOVE THE GREASE ON THE SCREWS AND THE
SCREW HOLES! The grease inhibits anodic corrosion (electrolysis).
Renew the grease on the screw connections after each time the fixture
has been opened.
 Carry out the installation when the weather is dry.
 Prepare the recess if not done yet. When installing the lighting unit
outdoors provide a gravel bed, 20 cm thick, beneath the installation pot.
This serves as a protection from corrosion.
 Prepare the power supply lead according to valid rules for outdoor
installations.
Separate Installation Steps
 Remove the shield by loosening the screws.
 Take the fixture out of the plastic casing.
 Direct the earth cable through the opening of the plastic casing. Fix the
plastic casing firmly into the earth.
 Remove the LED board.
 Direct the earth cable, in sufficient length, through the cable screwing.
 Secure the cable screwing using a suitable tool.
 Connect the product with the prepared low-voltage power supply.
 Fix the LED board again.
 Assemble the fixture in reverse order.
 Pay attention that the gasket fits properly. The bearing surface of the
gasket must be free of dirt. Tighten the screws on the shield in a cross-
wise order, to achieve an even pressure on the gasket.
 The product is now ready for operation.
4. FIRST OPERATION
On the first operation check if the product functions properly!
DANGER
In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external switch
or by the fuse.
 If touched or further operated there is danger from electric shock,
burning, or fire.
A malfunction exists when:
 visible damages appear.
 the product does not work properly (e.g. flickering).
 smoke, steam or crackling sounds appear.
 smell of burning is recognisable.
 an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
Notice for the electrician:
It is your responsibility to hand out the user manual on the reverse
side to the end user.
INSTALLATION MANUAL for RECESSED GROUND
FITTING
229311/17
ONLY FOR THE ELECTRICIAN!
ONLY FOR THE ELECTRICIAN!
12V AC