User manual

1. Use as directed:
This product serves exclusively lighting purposes and may:
 only be used with a voltage of 230V ~50Hz.
 only be used in dry condition,
 not in damp or dirt-endangered rooms.
 not in areas of high air humidity.
 not be exposed to strong mechanical loads or to strong
contamination.
 only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
 not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2. Technical Data:
149365 149375
Operating voltage: 230V ~50Hz
Safety class: I
Bulb: T 29-R,G10q, 32W 1x T 29-R,G10q, 32W
1x T 29-R,G10q, 40W
Dimensions (Ø/H): 45/9 cm
Pendulum length: 1,50 m
Weight: 3,05 kg 3,20 kg
Importer: SLV Elektronik GmbH
3. Installation
The electric connection may be executed only by an electric expert
who is familiar with the valid directives!
Attention: Switch off the power of the mains supply line or
respectively of the connection lead before doing any works
.
Use only
parts, which are supplied with the product or are described as accessories!
Otherwise the product or the installation might not be sufficiently safe.
Installation place:
The product is suited for ceiling installation.
Make sure that the product is mounted on a stable, even and tilt-fixed
background.
Separate Installation Steps
 Open the fitting (1). Loosen the screw and carefully take off the glass
(SLV art.-no. 924168).
 Insert the two starter with a quarter turn into the sockets (2).
 Insert the fluorescent rings into the clamps. Connect the plugs with
the bulbs. The surfaces with the edge must point up and respectively
down (3).
 Put the glass back on.
 Mark and drill the fastening holes for the mounting bracket of the
canopy. Do not damage the mains in the ceiling.
 Fasten the mounting bracket to the ceiling (4).
 Adjusting the pendulum length: Change the pendulum length, if
desired, by shortening the steel wires inside the canopy. Apply and
tighten the safety screw (5). You may adapt the length of the lead also.
Loosen the strain relief (A) on the canopy. Disconnect the wires from the
terminal block and shorten the lead to the desired length. Reconnect the
wires with the terminal block as before. Refasten the strain relief.
Electrical Connection (6)
 The product must be able to be separated by an all pole separation from
the current supply.
 149375: The electrical connection provides that two circuits may be
operated. The circuits are labelled as L1: 32W and L2: 40W.
 For electric connection attach the black or brown wire (live conductor) of
the mains supply with the clamp L and the blue wire (neutral conductor)
of the mains supply with the clamp N. The green-yellow wire (protective
conductor) of the mains supply has to be tightly screwed into the earth
clamp
of the product.
ENG
Instruction Manual ELSU / ISTU
 Now fasten the canopy back to the mounting bracket. Do not forget to
apply the toothed washers!
 Ensure that the pendant fitting holds securely!
 The product is now ready for operation.
4. Operation
:
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
 visible damages appear.
 the product does not work.
 smoke, steam or crackling sounds appear.
 an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention: Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
 Do not cover the product - provide free air circulation!
 Do not hang or fasten anything on the product, especially no decoration.
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
What is to do if a bulb is defect or does not work?
 Disconnect the product from power, before you exchange the bulbs.

Caution: Let the bulb cool down first before replacement – otherwise
considerable risk of injury exists because of the hot surface.
 Replace the bulbs only with bulbs of the same data like socket, power
and capacity. Every other sort of bulb can lead to damages of the light.
 Replacing the bulb: see Installation.
5. What else has to be considered?
Disconnect the product from power, before you…
1
3
2
4
6
5
A
N
oder
or
ou
o
of
N L1 L2
L1 L2
 clean or maintain the product.
 do any works on the product or its components (electric expert).
149365/75 06/2006 by SLV Elektronik GmbH
Technical Details are subject to change. Duplication prohibited !
F
Mode d'emploi
ELSU / ISTU
1. A utiliser comme indiqué :
Ce produit ne sert qu’à éclairer:
 il est prévu pour une tension de 230V ~50Hz.
 il peut uniquement être utilisé dans un endroit sec et surtout pas :
 dans un environnement poussièreux ou humide
 dans un environnement d'air humide
 il ne doit être soumis ni aux efforts mécaniques importants ni à un
encrassement important.
 il ne doit être utilisé qu’après examen si le produit a été stocké dans un
entrepôt humide ou sale.
 il ne doit pas être modifié.
Un non-respect de ces points peut causer un court-circuit ou une
décharge électrique!
2. Informations techniques:
149365 149375
Tension d'alimentation: 230V ~50Hz
Classe de protection: I
Lampes: T 29-R,G10q, 32W 1x T 29-R,G10q, 32W
1x T 29-R,G10q, 40W
Dimensions (Ø/H): 45/9 cm
Longueur pendante: 1,50 m
Poids: 3,05 kg 3,20 kg
Importateur: SLV Elektronik GmbH
3. Installation
La connection électrique doit être exécutée par un professionnel,
lequel est familier des normes en vigueur!
Attention: Mettez l’alimentation électrique ou le raccordement au
secteur hors tension avant de travailler!
Utilisez seulement des pièces qui ont été livrées avec le produit ou qui sont
uniquement décrites comme accessoires ! Sinon, l’installation ainsi que le
produit ne peuvent pas être garantis.
Lieu d'installation
Ce produit est fait pour un montage au plafond. Veillez à ce que le produit
soit monté de manière stable et résistante au basculement.
Etapes successives pour installer le luminaire
 Ouvrez prudemment la lampe (1). Pour cela, dévissez la vis à tête
moletée et enlevez prudemment le verre.
 Placez les deux démarreurs en les tournant d’un quart de tour dans les
douilles (2).
 Installation d'ampoule: Placez les anneaux de tube fluorescent dans
les pinces. Connectez les fiches avec les anneaux de tube fluorescent
(3). Les côtés avec la petite hauteur doivent montrer vers le haut ou bien
vers le bas (!).
 Remettez le verre.