Installation Sheet

ManualsBrandsSloan ManualsPlumbingRoyal Collection 1.6 GPF Single-Flush Concealed Manual Water Closet Flushometer in Rough Brass Color

Code No. 0816331

Rev. 8 (10/17)

INSTALLATION INSTRUCTIONS FOR STAINLESS STEEL

WATER CLOSETS, URINALS AND COMBINATION FIXTURES

Check that the “L” dimension shown on the flushometer package is correct for your

application. Determine the “L” dimension for your application by using the following

formula:

“L” dimension = Wall Thickness (to the nearest whole inch) + 2-3/4”

(Models 609, 611 and 613), 4-3/4” (Models 601 and 603) OR 6-3/4”

(Model 681).

Prior to installing the Sloan Prison Flushometer, perform the following functions using

the rough-in diagrams on Pages 2 and 3.

• Bore a 1-1/2” (38 mm) opening in wall for standard or hydraulic push button

actuator.

• Bore a 1-2” (25-51 mm) opening in wall for piping. Refer to the Rough-in drawings

on Pages 2 and 3. (This is NOT required if wall sleeve is used in conjunction

with fixture.)

• Install stainless steel prison fixture.

• Install drain line.

• Install water supply line.

NOTE: MAXIMUM DISTANCE FROM BUTTON TO VALVE IS 20’

(LONGER TUBING REQUIRED)

IMPORTANT:

• INSTALL ALL PLUMBING IN ACCORDANCE WITH

APPLICABLE CODES AND REGULATIONS.

• WATER SUPPLY LINES MUST BE SIZED TO PROVIDE AN

ADEQUATE VOLUME OF WATER FOR EACH FIXTURE.

• FLUSH ALL WATER LINES PRIOR TO MAKING

CONNECTIONS.

Sloan’s flushometers are designed to operate with 15 to 80 psi (103 to 552 kPa) of

water pressure. THE MINIMUM PRESSURE REQUIRED BY THE VALVE

IS DETERMINED BY THE TYPE OF FIXTURE SELECTED.

Consult fixture manufacturer for minimum pressure requirements. Most Low

Consumption water closets (1.6 gpf/6.0 Lpf) require a minimum flowing pressure of

25 psi (172 kPa).

LIMITED WARRANTY

Unless otherwise noted, Sloan Valve Company warrants this product, manufactured and sold for commercial or industrial uses, to be free from defects in material and

workmanship for a period of three (3) years (one (1) year for special finishes, SF faucets, PWT electronics and 30 days for PWT software) from date of first purchase. During

this period, Sloan Valve Company will, at its option, repair, replace, or refund the purchase price of any product which fails to conform with this warranty under normal use

and service. This shall be the sole and exclusive remedy under this warranty. Products must be returned to Sloan Valve Company, at customer’s cost. No claims will be

allowed for labor, transportation or other costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan

Valve Company for purpose of resale. This warranty does not cover the life of the batteries.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE

COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

Concealed Flushometer

with Standard

Push Button Actuator

Closet Flushometer

1½” (38 mm) Back Inlet

MODELS 601, 603, 611 & 681

Urinal Flushometer

1½” (38 mm) & 3/4” (19 mm)

Back Inlet

MODELS 609 & 613

Concealed Flushometer

with Hydraulic

Push Button Actuator

Closet Flushometer

1½” (38 mm) Back Inlet

MODELS 9603. 9611

Urinal Flushometer

1½” (38 mm) & 3/4” (19 mm)

Back Inlet

MODELS 9609 & 9613

PRIOR TO INSTALLATION

TOOLS REQUIRED FOR INSTALLATION

• Standard set of hex wrenches

• Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or smooth jawed spud wrench

Summary of content (8 pages)

PAGE 1
Code No. 0816331 Rev. 8 (10/17) INSTALLATION INSTRUCTIONS FOR STAINLESS STEEL WATER CLOSETS, URINALS AND COMBINATION FIXTURES Concealed Flushometer with Hydraulic Push Button Actuator Concealed Flushometer with Standard Push Button Actuator Closet Flushometer 1½” (38 mm) Back Inlet Closet Flushometer 1½” (38 mm) Back Inlet MODELS 9603.
PAGE 2
ROUGH-INS MODELS 601 & 603 MODEL 611 & 9611 “L” DIM † 4-3/4” (121 mm) + WALL THICKNESS MODEL 601 20-1/2” (521 mm) MODEL 603 16” (406 mm) 1” I.P.S.
PAGE 3
ROUGH-INS (CONTINUED) MODEL 9603 – WATER CLOSET MODEL *9611 - WATER CLOSET 1” I.P.S. SUPPLY (25 mm DN) PUSH BUTTON (TYPE AND LOCATION OPTIONAL) 16” (406 mm) 14-1/2” (368 mm) 16” (406 mm) MODEL 9609 - URINAL 14-1/2” (368 mm) 2-1/8” (54 mm) MIN.41/8” (105 mm) MAX. PUSH BUTTON (TYPE AND LOCATION OPTIONAL) 1” I.P.S.
PAGE 4
1 - INSTALL OPTIONAL SWEAT SOLDER ADAPTER (ONLY IF SUPPLY PIPE DOES NOT HAVE MALE THREAD) AND INSTALL CONTROL STOP A B For Sweat Solder applications, slide Threaded Adapter onto water supply pipe until end of pipe rests against shoulder of Adapter. Sweat solder the Adapter to pipe. C THREADED ADAPTER D WATER SUPPLY PIPE Install the Sloan Bak-Chek® Control Stop to the water supply line with the outlet positioned as required.
PAGE 5
STEPS TO ATTACH PLASTIC TUBING A The push button valve actuator is connected to the flushometer body by two plastic tubes, yellow and blue. Match color of the tubes to color on the actuator B Cut off excess plastic tubing leaving 3-4” (76-102 mm) of slack when push button actuator is installed. C Slide plastic tubing into its corresponding valve actuator fitting. Pull tubing to make sure connection is secure. (Tubing can be removed by pressing on blue/yellow connection button to release.
PAGE 6
4 - INSTALL FLUSHOMETER A Insert adjustable tailpiece into control stop. (For standard push button, also mount flushometer to actuator assembly.) Lubricate tailpiece o-ring with water. Hand tighten tailpiece coupling. (For standard push button, also hand tighten actuator assembly coupling). B Align Flushometer directly above the Vacuum Breaker Flush Connection by sliding the Flushometer Body IN or OUT as needed. Tighten Vacuum Breaker Coupling by hand.
PAGE 7
TROUBLESHOOTING GUIDE PUSH BUTTON ACTUATOR ASSEMBLY (HYDRAULIC PUSH BUTTON APPLICATIONS ONLY) IMPORTANT — LAWS AND REGULATIONS PROHIBIT THE USE OF HIGHER FLUSHING VOLUMES THAN LISTED ON FIXTURE OR FLUSHOMETER. 1. Push Button Leaks. The actuator cartridge has an accumulation of lime or its seals are damaged or worn. Replace the cartridge (HY-32-A).
PAGE 8
CARE AND CLEANING DO NOT use abrasive or chemical cleaners (including chlorine bleach) to clean Flushometers that may dull the luster and attack the chrome or special decorative finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel. While cleaning the bathroom tile, protect the Flushometer from any splattering of cleaner. Acids and cleaning fluids will discolor or remove chrome plating. PARTS LIST Item Part No. No.